Citroen C4 PICASSO 2016 2.G Owner's Manual

299
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Fitting a wheel
F Lower  the   vehicle   fully.
F  F old   the   jack   3   and   detach   it.
List of operations
F Put  the   wheel   in   place   on   the   hub.
F  S crew   in   the   bolts   fully   by   hand.
F
 
P
re-tighten   the   security   bolt   using   the  
w

heelbrace 1 fitted with the security
socket  5
  (depending   on   equipment).
F
 
P
re-tighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
The
 
jack
 
must
 
only
 
be
 
used
 
to
 
change
 
a
 w
heel
 
with
 
a
 
damaged
 
tyre.
The
 
jack
 
does
 
not
 
require
 
any
 
m

aintenance.
The
 
jack
 
conforms
 
to
 
European
 
l

egislation,
 
such
 
as
 
defined
 
in
 
the
 
M

achinery
 
Directive
 
2006/42/CE.
8
In the event of a breakdown

300
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels,
when  tightening   the   bolts   on   fitting,   it  
i

s normal to notice that the washers
do not come into contact with the
"space-saver"
  spare   wheel.   The   wheel  
i

s secured by the conical sur face of
each
  bolt.
After changing a wheel
To correctly store the punctured wheel
in the boot ( not in the location for the
space-saver wheel ), first remove the
central
  cover.
When
  using   the   "space-saver"   type  
s

pare   wheel,   do   not   exceed   50   mph  
(

80 km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y a CITROËN dealer or a qualified
workshop
  without   delay.
Have the punctured wheel repaired
and refitted to the vehicle as soon as
possible.
F
 
T

ighten
 
the
 
security
 
bolt
 
using
 
the
 w
heelbrace 1 fitted with the security
socket  5
 
(depending
 
on
 
equipment).
F
 
T

ighten
 
the
 
other
 
bolts
 
using
 
the
 
w

heelbrace 1
 
o

n l y.
F
 
R

efit
 
the
 
wheel
 
bolt
 
cover(s)
 
(depending
 
on
 
e

quipment).
F
 
S

tow
 
the
 
tools
 
in
 
the
 
box. The
  tyre   inflation   pressures   are   given   on   this  lab
el.
In the event of a breakdown

301
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Changing a bulb
For H7 type bulbs with lugs... take care to observe their correct installation
so
  as   to   ensure   the   best   lighting  
p

erformance.
Risk of electrocution
Xenon bulbs (D5S-25W) must be
replaced by a CITROËN dealer or a
qualified
 w
orkshop.
Front lamps
Model with xenon headlamps
1. Directional dipped beam headlamps (D5S-25W).
2.
 M

ain   beam   headlamps   (H7-55W).
3.
 D

aytime   running   lamps   /   sidelamps
 (

6   light   emitting   diodes   -   LEDs).
4.
D

irection indicators
 (

6   light   emittng   diodes   -   LEDs).
5.
 F

ront   foglamps   (H11-55W).
Model with halogen headlamps
1. Dipped  beam   headlamps   (H7-55W).
2. M ain   beam   headlamps   (H7-55W).
3.
 D

aytime
 r
unning
 lam
ps/sidelamps
 (

4   light   emitting   diodes   -   LEDs).
4.
 D

irection   indicators   (PW Y24W).
5.
 F

oglamps
 (
H11-55W). In
  some   weather   conditions   (e.g.   low  
t

emperature or humidity), the presence
of   misting   on   the   internal   sur face   of   the  
g

lass   of   the   headlamps   and   rear   lamps  
i

s   normal;   it   disappears   after   the   lamps  
h

ave   been   on   for   a   few   minutes.
Light- emitting diodes - LEDs
For replacement, contact a CITROËN dealer or
qualified w
orkshop.
8
In the event of a breakdown

302
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Directional dipped beam
headlamps (xenon model)Main beam headlamps (xenon model)
F Remove the protective plastic cover by pulling   the   tab.
F
 
P
ush   the   connector.
F
 
R
emove   the   bulb   and   change   it.
For reassembly, carry out these operations in
reverse
 o

rder.
D5S
 
xenon
 
bulbs
 
must
 
be
 
changed
 
b

y a CITROËN dealer or a qualified
workshop,
 
as
 
there
 
is
 
a
 
risk
 
of
 
el

ectrocution.
In the event of failure of one
of the D5S bulbs, it is recommended
that the bulb on the other side be
changed
 
at
 
the
 
same
 
time.
The headlamps have polycarbonate
lenses
 
with
 
a
 
protective
 
coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F
 
u

se
 
a
 
sponge
 
and
 
soapy
 
water
 
or
 
a
 
p

H neutral product,
F
 
w

hen
 
using
 
a
 
high
 
pressure
 
washer
 
o

n
 
persistent
 
marks,
 
do
 
not
 
keep
 
t

he lance directed towards the
lamps
 
or
 
their
 
edges
 
for
 
too
 
long,
 
s

o
 
as
 
not
 
to
 
damage
 
their
 
protective
 
c

oating
 a

nd
 sea

ls.
Changing
 
a
 
bulb
 
should
 
only
 
be
 
done
 
a

fter the headlamp has been switched
off
 
for
 
several
 
minutes
 
(risk
 
of
 
serious
 
b

urns).
F

D

o not touch the bulb directly with
your
 
fingers,
 
use
 
a
 
lint-free
 
cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging
 t

he
 h

eadlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
In the event of a breakdown

303
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Dipped beam headlamps
(halogen model)
F Remove the protective plastic cover by pulling   the   tab.
F
 
P
ush   the   connector.
F
 
R
emove   the   bulb   and   change   it.
For reassembly, carry out these operations in
reverse
 o

rder.
Main beam headlamps
(halogen model)
F Turn the protective plastic cover to remove   it.
F
 
D
isconnect   the   connector.
F
 
R
elease   the   clips.
F
 
R
emove   the   bulb   and   change   it.
For reassembly, carry out these operations in
reverse
 o

rder.
8
In the event of a breakdown

304
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
The direction indicator bulb is located below
the  front   lamp.
F

T
urn the bulb holder a quarter turn anti-
clockwise.
F
 
R
emove   the   bulb   holder.
F
 
C
hange   the   failed   bulb.
For reassembly, carry out these operations in
reverse
 o

rder.
Direction indicators Front foglamps
F Unclip  the   finisher   by   pulling   at   the   top.
F  R emove   the   two   screws   to   remove   the   unit.
F
 
T
urn   the   bulb   holder   a   quarter   turn.
F
 
R
emove   the   bulb   holder.
F
 
C
hange   the   failed   bulb.
For reassembly, carry out these operations in
reverse
  order,   pressing   on   the   finisher   to   refit   it.
Faster
 
flashing
 
of
 
a
 
direction
 
indicator
 
w

arning
 
lamp
 
(left
 
or
 
right)
 
indicates
 
a
 
f

ailed
 
bulb
 
on
 
that
 
side.
Direction indicators (light
emitting diodes - LED)
For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
In the event of a breakdown

305
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
You should contact a CITROËN dealer or a
qualified  workshop   for   the   replacement   of   the  
l

ight-emitting   diode   -   LED.
Door mirror spotlamps
Integrated direction indicator
side repeaters
You should contact a CITROËN dealer or a
qualified  workshop   for   the   replacement   of   these  
b

ulbs. 1.
D

irection indicators (PY21W amber)
.
2.
 S
idelamps   /   foglamps   (P21/5W)
.
Rear lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer
  or   qualified   workshop.
3.
 B

rake
 
lamps
 
/
 
sidelamps
 
(light-emitting
 d
iodes
 
-
 
LEDs).
4. R
eversing
 
lamps
 
(W16W).
5.
 D

irection
 
indicators
 
(PY21W).
Model with LED lamps
3. Sidelamps ( 5W5).
4. B rake   lamps   (P21/ W).
5.
 D

irection   indicators   (W Y16W).
6.
 R

eversing   lamps   (W16W).
Model with conventional bulb lamps
8
In the event of a breakdown

306
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Lamps on the tailgate
Contact a CITROËN dealer or a
qualified  workshop   for   the   replacement  
o

f   reversing   lamp   and   direction   indicator  
b

ulbs.
Identify
 
the
 
failed
 
bulb.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
access
 
cover.
F
 
R

emove
 
the
 
three
 
lamp
 
fixing
 
screws
 
A
.
F
 
D

isconnect
 
the
 
lamp
 
connector.
F

C

arefully remove the lamp from the outside
by
 
pressing
 
the
 
retaining
 
clip
 
B
.
F

T

urn the bulb holder a quarter of a turn
anti-clockwise   and   pull   the   bulb   out.
F
 
C

hange   the   bulb.
For reassembly, carry out these operations in
reverse
 o
rder.
Model with LED lamps
Model with conventional bulb lamps
In the event of a breakdown

307
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
1. Direction  indicators   (PY21W   amber).
2. S idelamps   /   foglamps   (P21/5W).
Rear lamps
3. Sidelamps  (light-emitting   diodes   -   LEDs).
4. B rake   lamps   (light-emitting   diodes   -   LEDs).
5.
 D

irection   indicators   (PY21W).
6.
 R

eversing   lamps   (light-emitting   diodes   -  
L

ED s).
Model with LED lamps
3. Sidelamps ( W5W).
4. B rake   lamps   /   sidelamps   (P21W).
5.
 D

irection   indicators   (W Y16W).
6.
 R

eversing   lamps   (W16W).
Model with conventional bulb lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer  or   qualified   workshop.
8
In the event of a breakdown

308
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Lamps on the tailgateModel with LED lamps
Model with conventional bulb lamps
Identify
 
the
 
failed
 
bulb.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
access
 
cover. F
 
R

emove
 
the
 
three
 
lamp
 
fixing
 
screws
 
A .
F
 
D

isconnect
 
the
 
lamp
 
connector.
F
 
C

arefully
 
r

emove
 
t

he
 
l

amp
 
f

rom
 
i

ts
 
h

ousing.
F

T

urn the bulb holder a quarter of a turn
anti-clockwise
 
and
 
pull
 
the
 
bulb
 
out.
F
 
C

hange
 
the
 
bulb.
For reassembly, carry out these operations in
reverse
 o

rder.
In the event of a breakdown