engine Citroen GRAND C4 PICASSO RHD 2016 2.G Owners Manual

Page 276 of 523

274
Coolant level
The coolant level should be close to   the   "MA X"   mark   but   should   never  
e

xceed   it.
In
 
addition,   as   the   cooling   system   is   pressurised,
 w

ait
 
at
 
least   one   hour   after   switching   off   the
 e

ngine
 
before   carrying   out   any   work.
To
 
avoid
 
any   risk   of   scalding,   unscrew   the   cap  
b

y
 
two
 
turns   to   allow   the   pressure   to   drop.  
W

hen
 
the
  pressure   has   dropped,   remove   the  
c

ap
 
and
 
top-up   the   level.
Fluid specification
The coolant must conform to the manufacturer's r ecommendations.
The cooling fan may star t after switching
off the engine: take care with ar ticles and
clothing that might be caught by the fan
blades. When   the   engine   is   warm,   the   temperature   of  
t

he   coolant   is   regulated   by   the   fan.To p p i n g - u p
The reservoir must be topped-up without delay b
y   a   CITROËN   dealer   or   a   qualified   workshop.
Diesel fuel additive level
(Diesel with particle filter)
The additive reservoir low level is indicated   by   fixed   illumination   of   this  
w

arning   lamp,   accompanied   by   an  
a

udible   signal   and   a   message   that  
t

he   particle   filter   additive   level   is  
t

oo low.
The
 
warning   lamp   comes   on   when   the   ignition  
i

s
 
switched   on,   or   every   time   the   stalk   is  
o

perated,
  until   the   reservoir   is   refilled.
Next
 
time
  you   stop,   refill   the   screenwash   /  
h

eadlamp
  wash   reservoir.
Screenwash/headlamp
wash level low
In the case of vehicles fitted with h
eadlamp   washers,   when   the   fluid r

eservoir   low   level   is   reached   this
 w

arning   lamp   comes   on   in   the
 i

nstrument   panel,   accompanied   by   an
 a

udible   signal   and   a   message. Avoid
  prolonged   contact   of   used   oil   or  
f

luids   with   the   skin.
Most
  of   these   fluids   are   harmful   to  
h

ealth   or   indeed   very   corrosive.
Do
  not   discard   used   oil   or   fluids   into  
s

ewers   or   onto   the   ground.
Take
  used   oil   to   a   CITROËN   dealer   or  
a

  qualified   workshop   (France)   or   to   an  
a

uthorised   waste   disposal   site.
Used products
Practical information

Page 277 of 523

275
Checks
12 V battery
The battery does not require any maintenance.
However,
  check   that   the   terminals  
a

re   clean   and   correctly   tightened,  
p

articularly   in   summer   and   winter.Refer
  to   the   manufacturer's  s
ervice   schedule   for   details   of   the  
r

eplacement   intervals   for   these  
c

omponents.
Air filter and passenger compartment filter
Replace the oil filter each time the engine   oil   is   changed.
Refer
  to   the   manufacturer's  
s

ervice   schedule   for   details   of  
t

he   replacement   interval   for   this  
c

omponent.
Oil filterThe presence of this label, in particular
with   the   Stop   &   Start   system,   indicates   the u

se   of   a   specific   12   V   lead-acid   battery
 w

ith   special   technology   and   specification.
 T

he   involvement   of   a   CITROËN   dealer
 o

r   a   qualified   workshop   is   essential   when
 r

eplacing   or   disconnecting   the   battery.
Unless
  other wise   indicated,   check   these   components   in   accordance   with   the   manufacturer's   service   schedule   and   according   to   your   engine.
Other wise,   have   them   checked   by   a   CITROËN   dealer   or   a   qualified   workshop.
Depending on the environment (e.g. dusty a
tmosphere)   and   the   use   of   the   vehicle   (e.g. city d

riving),
 r
eplace them twice as often if necessar y .
A
  clogged   passenger   compartment   filter   may   have
 a

n   adverse   effect   on   the   per formance   of   the   air
 c

onditioning   system   and   generate   undesirable
 o

dours.
Particle filter (Diesel)
The start of saturation of the particle
filter   is   indicated   by   the   fixed  
i

llumination   of   this   warning   lamp  
a

ccompanied   by   a   warning   message.
As
 
soon   as   the   traffic   conditions   permit,  
r

egenerate   the   filter   by   driving   at   a  
s

peed   of   at   least   40   mph   (60   km/h)   until  
t

he
 
warning   lamp   goes   off.
If
 
the   warning   lamp   stays   on,   this  
i

ndicates   a   low   additive   level.
For
  more   information   on   Checking
levels
 

and   the   Diesel   additive   level   in  
p

articular,   refer   to   the   corresponding  
s

ection.
On a new vehicle, the first particle
filter
  regeneration   operations   may   be  
a

ccompanied   by   a   "burning"   smell,  
w

hich   is   per fectly   normal.
Following
  prolonged   operation   of   the  
v

ehicle   at   very   low   speed   or   at   idle,  
y

ou
  may,   in   exceptional   circumstances,  
n

otice   the   emission   of   water   vapour   at  
t

he
 
exhaust   on   acceleration.   This   does  
n

ot affect the behaviour of the vehicle
or
 
the   environment.
When
 
carrying
 
out
 
work
 
on
 
the
 
battery,
 
refer
 
t

o the " 12 V batter y "
 
section
 
for
 
details
 
of
 
the
 
p

recautions
 
to
 
be
 
taken
 
before
 
disconnecting
 
t

he
 
battery
 
and
 
following
 
its
 
reconnection.
7
Practical information

Page 278 of 523

276
Brake wear depends on the style of   driving,   particularly   in   the   case o

f   vehicles   used   in   town,   over   short
 d

istances.   It   may   be   necessary   to   have
 t

he   condition   of   the   brakes   checked,
 e

ven   between   vehicle   services.
Brake pads
For information on checking brake disc   wear,   contact   a   CITROËN   dealer  
o

r   a   qualified   workshop.
Brake disc wear
Only use products recommended by CITROËN   or   products   of   equivalent  
q

uality
 an
d
 sp
ecification.
In
  order   to   optimise   the   operation   of  
u

nits   as   important   as   those   in   the  
b

raking   system,   CITROËN   selects   and  
o

ffers   very   specific   products.
After
  washing   the   vehicle,   dampness,  
o

r   in   wintry   conditions,   ice   can   form  
o

n   the   brake   discs   and   pads:   braking  
e

fficiency   may   be   reduced.   Make   light  
b

rake   applications   to   dry   and   defrost  
t

he   brakes.
Electric parking brake
For more information, refer to the "E lectric
parking brake - Operating faults "
  section.
This
  system   does   not   require   any  
r

outine   servicing.   However,   in   the  
e

vent   of   a   problem,   have   the   system  
c

hecked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Manual gearbox
The gearbox does not require any m
aintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   the   checking   interval   for  
t

his
 c
omponent.
Automatic gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   details   of   the   level  
c

hecking   interval   for   this   component.
To
  avoid   damaging   the   electrical   units,  
n

ever use   a   high   pressure   jet   wash   in  
t

he   engine   compartment.
Unless
  there   is   a   leak   in   the   circuit,   a   drop   in  
t

he   brake   fluid   level   indicates   that   the   brake  
p

ads   are   worn.
Practical information

Page 279 of 523

277
AdBlue® additive and SCR system
f
or
 
BlueHDi   Diesel   engines
To assure respect for the environment and c
onformity   with   the   new   Euro   6   emissions  
s

tandard,   without   adversely   affecting   the  
p

er formance   or   fuel   consumption   of   Diesel  
e

ngines,   CITROËN   has   taken   the   decision   to  
e

quip   its   vehicles   with   an   effective   system   that  
a

ssociates   SCR   (Selective   Catalytic   Reduction)  
w

ith   a   particle   filter   (FAP)   for   the   treatment   of  
e

xhaust   gases.
Presentation of the SCR system
Using a fluid called AdBlue® containing urea, a c
atalytic
 
converter
 
turns
 
up
 
to   85%   of   nitrogen  
o

xides
 
(NOx)
 
into
 
nitrogen
 
and   water,   which   are  
h

armless
 
to
 
health
 
and
 
the
 
environment. The
  AdBlue
® additive is held in a special t
ank
 
located
  under   the   boot   at   the   rear   of  
t

he
 
vehicle.
 
It   has   a   capacity   of   17   litres:   this  
p

rovides
 
a
 
driving   range   of   about   12   500   miles  
(

20
 
000
 
km),
  after   which   an   alert   is   triggered  
w

arning
 
you
 
when   the   reserve   remaining   is  
e

nough
 
for
 
just   1   500   miles   (2   400   km).
During
 
each
  scheduled   service   of   your   vehicle  
b

y
 
a
 
CITROËN   dealer   or   a   qualified   workshop,  
t

he
 
AdBlue
® additive tank is refilled in order to a
llow
 
normal   operation   of   the   SCR   system.
If
 
the
 
estimated   mileage   between   two   services  
i

s
 
greater
 
than   12   500   miles   (20   000   km),   we  
r

ecommend
  that   you   go   to   a   CITROËN   dealer  
o

r
 
a
 
qualified   workshop   to   have   the   necessary  
t

op-up
 
carried   out. Once
  the   AdBlue
® tank is empty, a s
ystem
 
required
  by   regulations  
p

revents
 
starting
 
of   the   engine.
If the SCR

is faulty, the level of
emissions
 
from
 
your   vehicle   will   no  
l

onger
 
meet
 
the
 
Euro   6   standard:   you  
v

ehicle
 
becomes
 
polluting.
In
 
the
 
event
 
of
 
a
 
confirmed   fault  
w

ith
 
the
 
SCR
 
system,   you   must   go  
t

o
 
a
 
CITROËN
 
dealer   or   a   qualified  
w

orkshop
 
as
 
soon   as   possible:   after  
a

 
running
 
distance   of   650   miles  
(

1 100
 
km),
 
a
 
system   will   be   triggered  
a

utomatically
 
to
 
prevent   engine   starting.
7
Practical information

Page 281 of 523

279
Recommendations on storage
AdBlue® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat
 
bottles   be   stored   in   a   cool   area   and  
p

rotected   from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can   be   kept  
f

or
 
at
 
least   a   year.
If
 
the
 
additive   has   frozen,   it   can   be   used   once   it  
h

as
 
completely   thawed   out.
Procedure
Before topping-up, ensure that the vehicle is parked   on   a   flat   and   level   sur face.
In
  wintry   conditions,   ensure   that   the  
t

emperature   of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer
 
area
 
for
 
a
 
few
 
hours
 
to
 
allow   the   top-up  
t

o
 
be
 
carried
 
out.
F
 
P

ress
 
the
 
START/STOP
 
button
 
to   switch  
o

ff
 
the
 
engine. F
 F or   access   to   the   AdBlue® tank, raise the b
oot
 
floor,
 
or
 
on
 
7-seat
 
versions,   unfold   the  
r

ight
 
hand
 
seat
 
in
 
the
 
third
  row.
Never
 
store
 
bottles
 
of
 
AdBlue
® in your
vehicle.
F
 
W
ithout   pressing,   turn   the   black   cap   a  
q

uarter   turn   anti-clockwise   and   lift   it   off.
F
 
T
urn   the   blue   cap   a   6
th of a turn anti-
c
lockwise.
F
 
L

ift
 
off
 
the
 
cap.
F
 
O

btain
 
a
 
bottle
 
of
 
AdBlue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank.
7
Practical information

Page 282 of 523

280
Important: if   your   vehicle's   AdBlue®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
messages
 
and  
t

he
 
impossibility
 
of
 
starting
 
the
 
engine,  
y

ou
 
must
 
add
 
at
 
least
 
3.8
 
litres
 
of
 
fluid. Important: w
hen topping-up after
running out of AdBlue®, signalled b
y
 
the
 
message
 
"Top-up
  AdBlue   :  
S

tarting
 
prevented",
 
you
 
must   wait  
f

or
 
approximately
 
5
 
minutes   before  
s

witching
 
on
 
the
 
ignition,
  without
opening the driver's door, unlocking
the vehicle, placing the key of the
"Keyless Entr y and Star ting" system
inside the vehicle or inser ting the
electronic key in the reader.
Switch
 
on
 
the
 
ignition,
 
wait   for  
1

0 seconds,
 
then
 
start
 
the   engine.
If
 
any
 
fluid
 
is
 
spilt
 
or
 
splashed,
 
wash
 
i

mmediately
 
w

ith
 
c

old
 
w

ater
 
o

r
 
w

ipe
 
w

ith
 
a

 
damp
 
cloth.
If
 
the
 
fluid
 
has
 
crystallised,
 
clean
 
it
 
off
 
u

sing
 
a
 
sponge
 
and
 
hot
 
water.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth. F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a
 6th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat   the   indicator   on   the   cap   lines   up   with  
t

he   indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
  the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.
Do
  not   dispose   of   AdBlue
® bottles in
the
 
household
 
waste.
 
Place   them   in   a  
c

ontainer
 
provided
 
for
 
this
  purpose   or  
t

ake
 
them
 
to
 
your
 
dealer.
Practical information

Page 286 of 523

284
1. Sealing
Repair procedure
Avoid removing any foreign bodies which   have   penetrated   into   the   tyre.F

U
ncoil the white pipe G  
f
ully.
F  
U
nscrew   the   cap   from   the   white   pipe.
F
C
onnect the white pipe to the valve of the
tyre   to   be   repaired.
F
 
S

witch   off   the   ignition.
F

T

urn the selector A to the "sealant"
position.
F
 
C

heck   that   the   switch   B is in
position "O" . F  
C
onnect   the   compressor's   electric   plug   to  
t

he   vehicle's   12   V   socket.
F  
S
tart   the   vehicle   and   leave   the   engine  
r

unning.Take care, this product is harmful if s
wallowed   and   causes   irritation   to   the   eyes.
Keep
  this   product   out   of   the   reach   of  
c

hildren.Do not start the compressor before c onnecting   the   white   pipe   to   the   tyre  
v

alve:   the   sealant   product   would   be  
e

xpelled   through   the   pipe.
In the event of a breakdown

Page 290 of 523

288
Checking / adjusting tyre pressures
You can also use the compressor without injecting   any   product,   to   check   and   if   necessary  
a

djust   your   tyre   pressures.
F

T
urn the selector A to the "Air"
position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.
F
 
C
onnect   the   black   pipe   to   the  
t

yre   valve. F
 C onnect   the   compressor's   electrical  
c

onnector   to   the   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   and   let   the   engine   run.
F
 
A
djust   the   pressure   using   the   compressor  
(

to   inflate:   switch   B in position "I";
 
t

o deflate:   switch   B in position "O"
 
and  
p

ress button C),
  according   to   the   vehicle's  
t

yre   pressure   label.
F
 
R
emove   the   kit   then   stow   it.Should
  the   pressure   of   one   or   more  
t

yres   be   adjusted,   it   is   necessary   to  
r

einitialise   the   under-inflation   detection  
s

ystem.
For
  more   information   on   Under-
inflation detection , refer to the
corresponding
 s

ection.
In the event of a breakdown

Page 314 of 523

312
Engine compartment fuses
The fusebox is placed in the engine compartment   near   the   battery.
Fuse N°Rating Functions
F18 10 ARight-hand
  main   beam.
F19 10 ALeft-hand
  main   beam.
F29 40 AWipers.Fuse table
Access to the fuses
F Unclip   the   cover,   by   pushing   the   two   red  l
atches   towards   the   rear   of   the   vehicle.
F
 
C
hange   the   fuse.
F
 
W
hen   you   have   finished,   close   the   cover  
c

arefully   to   ensure   correct   sealing   of   the  
f

usebox.
In the event of a breakdown

Page 315 of 523

313
12 V battery
The battery is located under the bonnet.
F or   access   to   the   (+)   terminal:
F
 
r
elease   the   bonnet   using   the   interior   lever,  
t

hen   the   exterior   safety   catch,
F
 
r
aise   the   bonnet   and   secure   it   with   its   stay,
F

l
ift the plastic cover for access to
the (+) terminal.
Access to the battery
Procedure for starting the engine using another battery or charging a discharged battery.
P rotect   your   eyes   and   face   before  
h

andling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Wash
  your   hands   after wards.
Versions
  equipped   with   Stop   &   Start   are  
f

itted   with   a   12   V   lead-acid   battery   of  
s

pecific
 t
echnology
 a
nd
 s
pecification.
Its
  replacement   should   be   carried   out  
o

nly
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 w

orkshop.
Batteries
  contain   harmful   substances  
s

uch   as   sulphuric   acid   and   lead.
They
  must   be   disposed   of   in  
a

ccordance   with   regulations   and   must  
n

ot,   in   any   circumstances,   be   discarded  
w

ith   household   waste.
Take
  used   remote   control   batteries   and  
v

ehicle batteries to a special collection
point.
General points
Lead-acid starter batteries
If your vehicle has an automatic g earbox,   do   not   try   to   start   the   engine  
b

y   pushing   the   vehicle.
The
  (-)   battery   terminal   is   not   accessible.  
A r

emote   earth   point   is   located   at   high   level  
u

nder   the   bonnet   (alongside   the   battery).
8
In the event of a breakdown

Page:   < prev 1-10 ... 51-60 61-70 71-80 81-90 91-100 101-110 111-120 121-130 130 next >