ESP FORD MUSTANG 1969 Volume One Chassis

02-02-07
Brake System

02-02-07

ANTI-SKID CONTROL SYSTEM

RELEASE PAWL CAM PIN

RELEASE PAWL CAM LEVER

RELEASE CABLE

H
1636-
A

FIG. 10—Parking Brake Control Assembly

With Manual Release—Typical

power unit with mounting bracket is

riveted to the control assembly. The

vacuum actuated piston within the

unit is connected by a rod to the

upper end of the release lever (Fig. 9).

The lower end of the release lever ex-

tends out for alternate manual release
in the event of vacuum power failure

or for optional manual release at any

time.

Hoses connect the power unit and

the engine manifold to a vacuum re-

lease valve in the transmission neutral

safety switch.
The anti-skid control system con-

sists of three major components (Fig.

39).
Mechanically driven electromag-

netic sensors at each rear wheel; an

electronic control module mounted

under the glove box; a vacuum pow-

ered actuator attached to a bracket on

the inside of the right front frame rail

under the toe board.

The sensors consist of steel rings

having teeth on their outer diameters,

pressed on each axle shaft just out-

board of the wheel bearing. The teeth

rotate past corresponding teeth on the

inside diameter of stationary steel

rings mounted in the bearing retain-

ers.
Also mounted in the retainers, are

ring-shaped permanent magnets and

coils of wire. Two wires from each

sensor connect the sensors to the con-

trol module.

The control module consists of solid

state electronic components sealed in

a container. It is connected to the sen-

sors and to a solenoid on the actuator.

The actuator is similar to a vacuum

brake booster and consists of three

parts.
A chamber divided by a vacuum

suspended diaphragm; a hydraulic cyl-

inder connected to the diaphragm; and

a solenoid connected electrically to the

control module.

IN-VEHICLE ADJUSTMENTS AND REPAIRS

After any brake service work, ob-

tain a firm brake pedal before moving

the vehicle. Riding the brake pedal

(common on left foot application)

should be avoided when driving the

vehicle.

BRAKE SHOE ADJUSTMENTS—

DRUM BRAKES

The hydraulic drum brakes are

self-adjusting and require a manual

adjustment only after the brake shoes

have been relined, replaced, or when

the length of the adjusting screw has

been changed while performing some

other service operation. The manual

adjustment is performed with the

drums removed, using the tool and the

procedure detailed below.

When adjusting the rear brake

shoes,
check the parking brake cables

for proper adjustment. Make sure that

the equalizer operates freely.
To adjust the brake shoes:

1.
Use Rotunda Tool HRE 8650,

(Fig. 11) to determine the inside diam-

eter of the drum braking surface.

2.
Reverse the tool as shown in Fig.

11 and adjust the brake shoe diameter

to fit the gauge. Hold the automatic

adjusting lever out of engagement

while rotating the adjusting screw, to

prevent burring the screw slots. Make

sure the adjusting screw rotates freely.

If necessary, lubricate the adjusting

screw threads with a thin, uniform

coating of MIC-100-A.

3.
Rotate Tool HRE 8650 around

the brake shoes to be sure of the set-

ting.

4.
Apply a small quantity of high

temperature grease to the points

where the shoes contact the backing

plate, being careful not to get the lu-

bricant on the linings.

5. Install the drums. Install Tinner-

man nuts and tighten securely.

6. Install the wheels on the drums
and tighten the nuts to specification.

7.
Complete the adjustment by

applying the brakes several times with

a minimum of 50 lbs pressure on the

pedal while backing the vehicle. After

each stop the vehicle must be moved

forward.

8. After the brake shoes have been

properly adjusted, check the operation

of the brakes by making several stops

while operating in a forward direction.

WHEEL CYLINDER REPAIR-

DRUM BRAKE

Wheel cylinders should not be di-

sassembled unless they are leaking or

unless new cups and boots are to be

installed. It is not necessary to remove

the brake cylinder from the backing

plate to disassemble, inspect, or hone

and overhaul the cylinder. Removal is

necessary only when the cylinder is

damaged or scored beyond repair.procarmanuals.com

02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

BOOT

PISTON
. BLEEDER .

CYLINDER
SCREW RETURN SPRING PIST0N

H1385-B

FIG. 72—Brake Wheel Cylinder—Typical

DISASSEMBLY

1.
Remove the links and the rubber

boots from the ends of the brake cyl-

inder. Remove the pistons, cups, and

return spring from the cylinder bore

(Fig. 12).

2.
Remove the bleeder screw from

the cylinder.

INSPECTION

1.
Wash all parts in clean brake

fluid. Dry with compressed air.

2.
Replace scored pistons. Always

replace the rubber cups and dust

boots.
3.
Inspect the cylinder bore for

score marks or rust. If either condi-

tion is present the cylinder bore must

be honed. However, the cylinder

should not be honed more than 0.003

inch beyond its original diameter.

4.
Check the bleeder hole to be sure

that it is open.

ASSEMBLY

1.
Apply a light coating of heavy-

duty brake fluip! to all internal parts.

2.
Thread the bleeder screw into the

cylinder and tighten securely.

3.
Insert the return spring, cups,

and pistons into their respective posi-

tions in the cylinder bore (Fig. 12).
Place a boot over each end of the cyl-

inder. Bleed the brake system.

HYDRAULIC LINE REPAIR

Steel tubing is used throughout the

brake system with the exception of the

flexible hoses at the front wheels and

at the fear axle housing brake tube

connection (Figs. 17 thru 21).

Always bleed the applicable pri-

mary or secondary brake system after

primary or secondary brake system

hose or line replacement. Centralize

the pressure differential valve after

bleeding the system.

BRAKE TUBE

REPLACEMENT

If a section of the brake tubing be-

comes damaged, the entire section

should be replaced with tubing of the

same type, size, shape and length.

Copper tubing should not be used in a

hydraulic system. When bending

brake tubing to fit underbody or rear

axle contours, be careful not to kink

or crack the tube.

All brake tubing should be double

flared properly to provide good leak-

proof connections. Clean the brake

tubing by flushing with clean brake

fluid before installation.

When connecting a tube to a hose,

tube connector, or brake cylinder,

tighten the tube fitting nut to specified

torque with Milbar tool 1112-144 or

equivalent.

BRAKE HOSE

REPLACEMENT

A flexible brake hose should be re-

placed if it shows signs of softening,

cracking, or other damage.

When installing a new front brake

hose,
position the hose to avoid con-

tact with other chassis parts. Place a

new copper gasket over the hose fit-

ting and thread the hose assembly into

the front wheel cylinder. Engage the

opposite end of the hose to the brack-

et on the frame. Install the horsesho-

e-type retaining clip, and connect the

tube to the hose with the tube fitting

nut (Figs. 17 thru 21).

A rear brake hose should be in-

stalled so that it does not touch the

muffler outlet pipe or shock absorber.

Thread the hose into the rear brake

tube connector. Engage the front end

of the hose to the bracket on the

frame. Install the horseshoe-type re-

taining clip, and connect the tube to

the hose with the tube fitting nut.procarmanuals.com

02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take care
to

avoid loosening
the
bridge bolts that

hold
the two
halves
of the
caliper
to-

gether.

4.
Lift
the
caliper assembly
off the

rotor
and
place
it on the
bench.

Installation

1.
If the
caliper assembly
is to be

replaced, transfer
the
steel tubing
and

the bleeder screw
to the new
caliper.

2.
Position
the
caliper assembly
on

the rotor,
and
mate
the
mounting bolt

holes
in the
caliper with those
in the

spindle.
It may be
necessary
to
push

the caliper pistons into
the
cylinder

bores
to
obtain clearance between
the

shoe
and
lining assembly
and the

rotor.
The
shoe
and
lining assemblies

should
be
seated properly
on the

bridges.

3.
Install
the
caliper
to
spindle
re-

taining bolts
and
torque them
to
spec-

ification. Check
to
insure that
the

rotor runs squarely
and
centrally
be-

tween
the two
halves
of the
caliper.

These should
be
approximately 0.090-

0.120 inch clearance between
the
cali-

per
and the
rotor outside diameter

(Fig.
6).

4.
Position
the
steel transfer tube

brake hose bracket
and
caliper assem-

bly
to the
spindle. Install
the
retaining

bolts then torque them
to
specifica-

tion.

5.
Connect
the
front wheel steel

transfer tube from
the
caliper
to the

front brake hose connector. Check
the

hose
for
proper installation
(Fig. 21).

6. Bleed
the
brake system
and cen-

tralize
the
differential valve
as out-

lined
in
Part
2-1.
Check
the
master

cylinder fluid level
and add the
speci-

fied fluid,
as
required. Pump
the

brake pedal several times
to
actuate

the piston seals
and to
position
the

shoe
and
lining assemblies.

7.
Install
the
wheel
and
tire assem-

bly
and the
wheel cover.

8. Road test
the
vehicle.

DISC BRAKE SHOE
AND

LINING

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire from
the
hub and
rotor assembly.

2.
Remove
the
caliper from
the ve-

hicle following
the
procedures outlined

under Disc Brake Caliper Assembly.

3.
To
facilitate removal
of the
cali-

per assemblies,
the
piston
may
have
to

be pushed into
its
bore. Apply
a

steady inward pressure against
the

inner shoe
and
lining assembly. Main-

tain
the
pressure
for at
least
a
minute.

4.
Slide
the two
outer shoe retain-

ing clips
off the
retaining pins
(Fig.

23).

5.
Remove
the two
retaining pins

from
the
outer shoe, then remove
the

shoe from
the
stationary caliper.

6. Slide
the
inner brake shoe
out-

ward until
it is
free
of the
hold-down

springs, then remove
the
brake shoe.

7.
Remove
the
caliper locating pins

and stabilizer attaching bolts, then
re-

move
and
discard
the
stabilizer
or sta-

bilizers.

8. Remove
the
locating
pin
insula-

tors from
the
anchor plate.

Installation

When installing
new
shoes
and lin-

ings
it
will
be
necessary
to
force
the

piston
to the
bottom
of its
bore.

Apply sufficient pressure
to
overcome

the grip
of the
piston seal
on the pis-

ton.

1.
Install
new
caliper locating
pin

insulators
in the
anchor plate.

2.
Position
the
caliper assembly
in

the anchor plate.

3.
Position
the new
stabilizer
or

stabilizers
and
install
the
caliper locat-

ing pins
to
engage approximately four

threads.

If
the
caliper locating pins
are
rust-

ed
or
corroded they should
be re-

placed.

Apply water
or
isopropyl alcohol
to

the caliper locating pins before instal-

lation.
Oil or
grease must
not be
used

on
the
locating pins.

4.
Position
the
outer brake shoe
on

the caliper
and
install
the two
retain-

ing pins
and
clips.

5.
Install
the
inner brake shoe
so

that
the
ears
of
shoe
are on top of the

anchor plate bosses
and
under
the

shoe hold-down springs.

6. Position
the
shoe
and
lining

assemblies
so
that
the
caliper assem-

bly
can be
placed over
the
rotor.
Ro-

tate
a
hammer handle between
the lin-

ings
to
reset
the
stabilizers.

7.
Install
the
caliper assembly over

the rotor
and on the
spindle. Install

the
two
caliper attaching bolts,
and

torque them
to
specifications.
The

upper bolt must
be
tightened first.
In-

stall
the
safety wire
and
twist
the
ends
at least five turns. Push
the
wire ends

against
the
spindle
to
avoid interfer-

ence with
the
brake hose
and the

steering stop.

8. With moderate pressure applied

to
the
brake pedal, torque
the
stabiliz-

er attaching screws
and
caliper locat-

ing pins
to
specification.

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire
as-

sembly from
the hub and
rotor assem-

bly.
Be
careful
to
avoid damage
or in-

terference with
the
caliper splash

shield, bleeder screw fitting
or
transfer

tube.

2.
Remove
the two
bolts that retain

the caliper splash shield,
and
remove

the shield
(Fig. 4).

3.
To
facilitate removal
and
instal-

lation
of the
shoe
and
lining assem-

blies,
the
pistons must
be
pushed into

their bores. Apply
a
steady inward

pressure against each shoe
and
lining

assembly toward
its
respective caliper

housing
on
each side
of the
rotor
(Fig.

6).
Maintain
the
pressure
for at
least

a minute.
If the
pistons will
not go ifi

easily, force them
in
with water pump

pliers.

4.
Grasp
the
metal flange
on the

outer
end of the
shoe with
two
pairs

of pliers
and
pull
the
shoe
out of the

caliper (Fig.
25).

Installation

1.
Position
a new
shoe
and
lining

assembly
on
each side
of the
rotor
so

that
the
lining faces
the
rotor.
Be
sure

AB

AB

USE SECOND

PAIR
OF

PLIERS HERE

H 1651
A

FIG. 25—Removing Disc Brake

Shoe
and
Lining Assembly—

Lincoln Continentalprocarmanuals.com

02-02-19
Brake System

02-02-19

that the tabs on the shoe flanges seat

fully against the caliper bridges (Fig.

25).

2.
Install the caliper splash shield

and secure the shield to the caliper

with two retaining bolts (Fig. 4).

3.
Pump the brake pedal several

times until a firm pedal is obtained

and the shoe and lining assemblies are

properly seated.

4.
Install the wheel and tire assem-

bly on the hub and rotor assembly.

5.
Check and refill the master cyl-

inder reservoir with specified brake

fluid as required.

6. Road test the car.

It should not be necessary to bleed

the system after a shoe and lining re-

placement.

FRONT WHEEL HUB AND

ROTOR ASSEMBLY-

DISC BRAKES

REMOVAL

1.
Remove the wheel and tire from

the hub (Figs. 23 and 24). Be careful

to avoid damage or interference with

the bleeder screw fitting. On Lincoln

Continental models be careful to avoid

damage to the caliper splash shield or

transfer tube.

2.
Remove the caliper assembly

from the spindle and the rotor. If the

caliper does not require servicing, it is

not necessary to disconnect the brake

hose or remove the caliper from the

vehicle. Position the caliper out of the

way, and support it with a wire to

avoid damaging the caliper or stretch-

ing the hose. Insert a clean cardboard

spacer between the linings to prevent

the piston from coming out of the cyl-

inder bore while the caliper is re-

moved.

Handle the rotor and caliper assem-

blies in such a way as to avoid defor-

mation of the rotor and nicking,

scratching or contamination of the

brake linings.

3.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

4.
Remove the hub and rotor as-

sembly from the spindle.

INSTALLATION

1.
If the rotor is being replaced, re-

move the protective coating from the

new rotor with carburetor degreaser.

Pack a new set of bearings with speci-
fied grease (M-1C75B), and install the

inner bearing cone and roller assembly

in the inner cup. Pack grease lightly

between the lips of a new grease seal

and install the seal (Figs. 23 and 24).

If the original rotor is being in-

stalled, make sure that the grease in

the hub is clean and adequate, that

the inner bearing and grease seal are

lubricated and in good condition, and

that the rotor braking surfaces are

clean.

2.
Install the hub and rotor assem-

bly on the spindle.

3.
Lubricate and install the outer

wheel bearing, washer and adjusting

nut.

4.
Adjust the wheel bearings to

specification, and then install the nut

lock, cotter pin, and grease cap. The

wheel bearing adjustment is especially

important with disc brakes.

5. Mount the caliper assembly on

the spindle following the Disc Brake

Caliper Assembly Installation proce-

dure in this section.

DISC BRAKE ROTOR

SPLASH SHIELD

REMOVAL

1.
Remove the caliper and the hub

and rotor assembly as outlined under
Removal in the foregoing procedure

(it is not necessary to disconnect hy-

draulic connections).

2.
Remove the three bolts that at-

tach the splash shield to the spindle,

and remove the shield (Figs. 23 and

24).

3.
Remove and discard the splash

shield to spindle gasket.

INSTALLATION

1.
Install a new splash shield to

spindle gasket.

2.
If the shield is bent, straighten it

out before installation. Position the

shield to the mounting bracket, install

the attaching bolts, nuts and torque

them to specification.

3.
Install the hub and rotor assem-

bly and the caliper as outlined under

Installation in the foregoing proce-

dure.

DUAL MASTER CYLINDER—

NON POWER BRAKES

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 26.

BUSHING

HAIRPIN

RETAINER

BUSHING

STOPLIGHT SWITCH

13480
HI 637-A

FIG. 26—Dual Master Cylinder Installation— Non Power Brakes

Ford,
Mercury, and Meteorprocarmanuals.com

02-02-39
Brake System

02-02-39

MAJOR REPAIR OPERATIONS

BRAKE DRUM REFINISHING

Minor scores on a brake drum can

be removed with sandpaper. A drum

that is excessively scored or shows a

total indicator runout of over 0.007

inch should be turned down. Remove

only enough stock to eliminate the

scores and true up the drum. The refi-

nished diameter must not exceed 0.060

inch oversize.

Check the inside diameter of the

brake drum with a brake drum mi-

crometer (Tool FRE-14^1).

If the drum diameter is less than

0.030 inch oversize after refinishing^

standard lining may be installed. If

the drum diameter is 0.030—0.060

inch oversize after refinishing, oversize

lining must be installed.

After a drum is turned down, wipe

the refinished surface with a cloth

soaked in clean denatured alcohol. If

one drum is turned down, the opposite

drum on the same axle should also be

cut down to the same size.

ROTOR REFINISHING

Rotunda Disc Brake Attachment,

FRE-2249-2, is the only recommended

tool to refinish the disc brake rotors.

The step-by-step resurfacing procedure

provided with the tool must be ad-

hered to.

The finished braking surfaces of the

rotor must be flat and parallel within

0.0007 inch; lateral runout must not

exceed 0.003 inch total indicator read-

ing, and the surface finish of the brak-

ing surfaces are to be 80/15 micro

inches. The minimum limiting dimen-

sions (Figs. 11 and 12, Part 2-1) from

the inboard bearing cup to the out-

board rotor face and from the inboard

bearing cup to the inboard rotor face

must be observed when removing ma-

terial from the rotor braking surfaces.

On all models except Lincoln Con-

tinental, the limiting dimensions are to

be measured with a ball and gage bar

(Rotunda Kit FRE-70160).

BRAKE SHOE RELINING

Brake linings that are worn to with-

in 1/32 inch of the rivet head or are

less than 0.030 inch thick (bonded lin-

ing) or have been contaminated with

brake fluid, grease or oil must be re-

placed. Failure to replace worn linings

will result in a scored drum. When it
is necessary to replace linings, they

must also be replaced on the wheel on

the opposite side of the vehicle.

Inspect brake shoes for distortion,

cracks, or looseness. If this condition

exists,
the shoe must be discarded. Do

not attempt to repair a defective brake

shoe.

1.
Wash the brake shoes thoroughly

in a clean solvent. Remove all burrs

or rough spots from the shoes.

2.
Check the inside diameter of the

brake drum with a brake drum mi-

crometer (tool FRE-1431). If the di-

ameter is less than 0.030 inches over-

size,
standard lining may be installed.

If the diameter is 0.030—0.060 inches

oversize, oversize lining should be in-

stalled.

3.
Position the new lining on the

shoe.
Starting in the center, insert and

secure the rivets, working alternately

towards each end. Replacement lin-

ings are ground and no further grind-

ing is required.

4.
Check the clearance between the

shoe and lining. The lining must seat

tightly against the shoe with not more

than 0.008 inch clearance between any

two rivets.

RETAINER - 2B245
DUAL MASTER CYLINDER

DISASSEMBLY

1.
Clean the outside of the master

cylinder and remove the filler cover

and diaphragm. Pour out any brake

fluid that remains in the cylinder. Dis-

card the old brake fluid.

2.*
Remove the secondary piston

stop bolt from the bottom of the cyl-

inder (Figs. 40 and 41).

3.
Remove the bleed screw, iL re-

quired.

4.
Depress the primary piston and

remove the snap ring from the retain-

ing groove at the rear of the master

cylinder bore (Fig. 42). Remove the

push rod and the primary piston as-

sembly from the master cylinder bore.

Do not remove the screw that retains

the primary return spring retainer, re-

turn spring, primary cup and protec-

tor on the primary piston. This assem-

bly is factory pre-adjusted and should

not be disassembled.

5.
Remove the secondary piston as-

sembly. Do not remove the outlet tube

seats,
outlet check valves and outlet

SECONDARY SYSTEM

BRAKE OUTLET
COVER -2166

GASKET-2167

MASTER CYLINDER -2155

SNAP RING -7821

BOOT

PUSH ROD

PRIMARY PISTON

ASSEMBLY - 2169

tTUBE SEAT-

2B220
* SECONDARY PISTON

ASSEMBLY - 2A502

• NOT USED ON POWER BRAKE EQUIPPED VEHICLES

fNOT SERVICED

•REPLACE AS AN ASSEMBLY ONLY

H 1499-B

FIG. 40— Dual Master Cylinder Disassembled—Except Disc Brakesprocarmanuals.com

02-02-42
Brake System

02-02-42

CALIPER
ABUTMENTS

OUTBOARD
CALIPER HOUSING

DUST
BOOT RETAINING GROOVE

DUST
BOOT (4)
PISTON
SEAL (4)

EXTERNAL

TRANSFER
TUBE

SCREW

INBOARD
CALIPER HOUSING

FLEXIBLE
HOSE-^
H1367-C

FIG. 46—Caliper Assembly — Disassembled—Lincoln Continental

9. Remove the rubber piston seals

from the grooves in the cylinder bores

by carefully inserting the point of a

small knife or other pointed instru-

ment under the seal and raising the

seal up far enough to be pulled out

with the fingers.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent (Fig. 46).

Use clean, dry, compressed air to

clean out and dry the grooves and

passage ways. Be sure that the caliper
bore and component parts are com-

pletely free of any foreign material.

Check the cylinder bores and pis-

tons for damage or excessive wear.

Replace the piston if it is pitted,

scored, or the chrome plating is worn

off. Check the caliper dust boot re-

tainer for wear or damage.

Assembly

1.
Clamp the caliper in a vise and

secure it by the mounting flange on

the inboard housing.

2.
Apply a film of clean brake fluid
to new caliper piston seals and install

them in the grooves of the cylinder

bore.
The seal should be positioned at

one area in the groove and gently

worked around. Do not use the origi-

nal seals.

3.
Install the new dust boots by set-

ting the flanges squarely in the outer

grooves of the caliper bores.

4.
Coat the pistons with the speci-

fied fluid and install the pistons inPthe

cylinder bores. Spread the dust boots

over the pistons as they are installed.

Seat the dust boots in the piston

grooves.

5.
Coat the outside diameter of the

pistons with brake fluid and install

them in the cylinder bores so that the

open end of the piston and ihe boot

retaining groove face out of the bore.

To avoid cocking, locate the piston

squarely in the bore and apply a slow

steady pressure. If a piston will not

easily go all the way into the bore, re-

move it and thoroughly inspect the

cylinder bore, the piston seal and the

installation of the seal. If the piston

still will not go in with bore in good

condition and the piston seal properly

installed, use the tool shown in Fig.

45.
Rotate the piston with the tool

while pushing it inward at the same

time.

6. Carefully install four new dust

boots on the caliper housings and pis-

tons.
Be sure that each boot is fully

seated in the groove of its respective

caliper housing and piston (Fig. 46).

Do not use the original dust boots.

7.
Install the external transfer tube.

8. Install the flexible brake hose to

the caliper.

9. Install the caliper assembly on

the spindle, and install the shoe and

lining assemblies and the splash shield

as outlined in Section 2. Check the

caliper for fluid leaks under maximum

pedal pressures. Do not move the car

until a firm brake pedal is obtained.procarmanuals.com

03-02-02
Suspension

03-02-02

COMPONENT INDEX

REAR SPRING

Disassembly
and
Overhaul

Removal
and
Installation

REAR SUSPENSION

Description

REAR SUSPENSION LOWER
ARM

Removal
and
Installation

REAR SUSPENSION UPPER
ARM

Removal
and
Installation

SPRING LEAVES
AND
TIE-BOLT

Removal
and
Installation

STABILIZER

Removal
and
Installation

TRACK
BAR

Removal
and
Installation

UPPER
ARM
-
REMOVED

Removal
and
Installation

UPPER
ARM
SHAFT AND/OR BUSHING

Removal
and
Installation

UPPER BALL JOINT

Removal
and
Installation
MODEL APPLICATION
All
Models
Ford

N/A

02-23

02-02

02-24

02-25

N/A

02-11

02-25

N/A

N/A

02-08
Mercury
N/A

02-23

02-02

02-24

02-25

N/A

02-11

02-25

N/A

N/A

02-08
Meteor
N/A

02-23

02-02

02-24

02-25

N/A

02-11

02-25

N/A

N/A

02-08
Cougar
N/A

02-25

02-04

N/A

N/A

N/A

02-11

N/A

N/A

02-09

02-08
Fairlane
N/A

02-25

02-04

N/A

N/A

N/A

02-11

N/A

N/A

02-09

02-08
Falcon
N/A

02-25

02-04

N/A

N/A

N/A

02-11

N/A

N/A

02-09

02-08
Montego
N/A

02-25

02-04

N/A

N/A

N/A

02-11

N/A

N/A

02-09

02-08
Mustang
N/A

02-25

02-04

N/A

N/A

N/A

02-11

N/A

N/A

02-09

02-08
Lincoln-
Continental
02-28

02-26

02-04

N/A

N/A

02-29

N/A

N/A

02-27

N/A

02-10
Thunderbird
N/A

02-23

02-02

02-24

02-25

N/A

02-11

02-25

N/A

N/A

02-08
Continental-
Mark III
N/A

02-23

02-02

02-24

02-25

N/A

02-11

02-25

N/A

N/A

02-08

A page number indicates that
the
item
is
for the
vehicle listed
at
the
head
of
the
column.

N/A indicates that
the
item
is
not
applicable
to
the
vehicle listed.

DESCRIPTION

FRONT SUSPENSION

Each front wheel rotates
on a

spindle.
The
upper
and
lower ends
of

the spindle
are
attached
to
upper
and

lower ball joints which
are
mounted
to

an upper
and
lower
arm
respectively.

The upper
arm
pivots
on a
bushing

and shaft assembly which
is
bolted
to

the frame.
The
lower
arm
pivots
on a

bolt
in the
front crossmember (Figs.
1,

2
and 3). A
coil spring seats between

the lower (upper
on
Cougar, Fairlane,

Falcon, Montego
and
Mustang)
arm

and
the top of the
spring housing.
A

double action shock absorber
is
bolted

to
the arm and the top of the
spring

housing.
REAR SUSPENSION

FORD, MERCURY,

METEOR, THUNDERBIRD
AND

CONTINENTAL MARK
III

Each rear wheel,
hub, and
brake

drum assembly
is
bolted
to the
rear

axle shaft flange.
The
axle shaft
as-

sembly rotates
in the
rear axle hous-

ing.

The rear axle housing
is
suspended

from
the
frame
by a
coil spring
and

shock absorber
at
each side
of the ve-

hicle
and by
three arms
(one
upper

and
two
lower) which pivot
in the

frame members
(Fig.
4).

Each coil spring
is
mounted
be-

tween
a
lower seat, which
is
welded
to

the axle housing,
and an
upper seat

which
is
integral with
the
frame.
The upper
end
of
the
rear shock
ab-

sorber
is
attached
to the
spring upper

seat;
the
lower
end is
bolted
to a

bracket
on the
axle housing.

The upper suspension
arm
attaches

to
the
right side
of the
axle housing

through
an
eccentric pivot bolt
and a

bracket which
is
welded
to the top of

the housing.
The
forward
end of the

arm
is
connected
by a
pivot bolt
to

the frame crossmember.

Each lower suspension
arm
attaches

to
one end of the
axle housing

through
a
pivot bolt
and a
bracket

which
is
welded
to the
underside
of

the housing.
The
forward
end of the

arm
is
connected
by a
pivot bolt
to

the frame side member.

A track
bar is
connected between

the upper
arm
bracket
on the
axle

housing
and a
mounting bracket
on

the left frame side rail.
procarmanuals.com

03-04-03
Automatic Air Leveling System — Lincoln Continental

03-04-03

outlet lines to their respective parts.

3.
Adjust the trim height as de-

tailed in Section 4.

4.
Connect the link to the arm.

5.
Remove the jack stands and

lower the vehicle.

SUPER LIFT SHOCK ABSORBER

REMOVAL

1.
Raise the vehicle and place jack

stands under the axle to compress the

super lift.

2.
Loosen the air line or lines (right

super lift) slowly to release the air
from the system. Then, disconnect the

line or lines.

3.
Remove the three mounting plate

attaching screws from the upper end

of the super lift.

4.
Remove the attaching nut and

washer from the lower end of the

super lift and remove it from the vehi-

cle.

5.
Remove the nut, outer washer

and the insulator that attach the super

lift to the mounting plate. Remove the

plate, remaining insulator and washer.

INSTALLATION

1.
Position a washer, insulator,

mounting plate, insulator, washer and
nut on the stud at the upper end of

the super lift. Torque the nut to speci-

fication.

2.
Install the mounting plate, outer

insulator, washer and nut on the stud.

Torque the nut to specification.

3.
Attach the mounting plate and

shock absorber to the crossmember

with the attaching screws to specifica-

tions.

4.
Connect the lower end of the

super lift to the mounting stud with

the washers and attaching nut. Torque

the nut to specification.

5.
Connect the air line or lines

(right super lift) to the super lift.

6. Start the engine and check for

leaks.

3 IN-VEHICLE ADJUSTMENTS AND REPAIRS

REGULATOR ADJUSTMENT HEIGHT CONTROL VALVE

The regulator may be adjusted if

the regulator pressure is under 100 psi

with the reservoir pressure at a mini-

mum of 140 psi. If the regulated pres-

sure exceeds 130 psi, the regulator

must be replaced.

To adjust the regulator, remove the

boot and reposition the sleeve and re-

tainer deeper into the body of the re-

gulator, using a deep well socket (Fig.

4).
If the regulator pressure remains

under 100 psi, replace regulator.
SILICONE FLUID

REPLACEMENT

If the height control valve time

delay does not fall within specifica-

tion, the silicone fluid must be re-

placed. Then repeat the time delay

test. If delay is still not within specifi-

cations, replace the height control

valve.

1.
Remove control valve and clean
the exterior of the valve thoroughly.

2.
Position the valve with delay

plug on top. Remove delay plug and

drain silicone fluid from the chamber.

Remove the O-ring from the chamber

(Fig. 5), and discard the O-ring.

3.
Remove the cover plate retaining

ring, using snap ring pliers. Remove

the delay cover from the valve body.

Remove the O-ring from the chamber,

and discard the O-ring.

4.
Place a new O-ring over the

delay plug and install the plug. Tor-

que the plug to 20-30 in-lbs. .

5.
Pour silicone fluid into the delay

piston chamber until fluid level is 5/16

inch below the top edge of the body.

Add or remove fluid with an eye drop-

per until the proper fluid level is

reached.

6. Hold the control valve body in a

vise with the delay chamber elevated

slightly. Carefully operate the lever to

purge trapped air from the fluid.

7.
Place a new O-ring in the groove

around the delay piston bore. Install

5/16" TO

FLUID LEVEL

F 1405 A

FIG. 4—Adjusting Regulator
F1406 A

FIG. 5—Replacing Silicone Fluidprocarmanuals.com

03-05-09

Steering Columns And Linkage

03-05-09

FAIRLANE, FALCON

AND MONTEGO

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

siwtch (with automatic transmission)

and back-up light switch wires from

the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear (Fig.

12).
6. Remove the nuts and bolts that

secure the column retainer and seal at

the toe plate.

7.
Disconnect the nuts that secure

the column upper and lower brackets

to the brake pedal support bracket

and the dash panel.

8. Lift the column from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Make sure that the wheels

are in the straight ahead position and

that the steering wheel spokes are in a

horizontal position when the flex cou-

pling engages the input shaft splines.

2.
Install but do not tighten the

nuts that secure the column upper and

lower brackets to the brake pedal sup-
port bracket and the dash panel.

Make certain the column is properly

positioned relative to the flex coupling

inpui shaft connection.

3.
Install and tighten the flex cou-

pling-to-steering gear attaching bolt.

4.
Tighten the nuts at the brake

pedal support bracket and the dash

panel.

5.
Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate.

6. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

7.
Connect the neutral start switch

(if so equipped) and back-up light

switch to their respective terminals.

8. Connect the turn signal switch

wires.

COLUMN UPPER \

BRACKET-3506 V

BRAKE PEDAL

SUPPORT BRACKET

TRIMSHROUD-3530

UPPER CLAMP-3507,

COLUMN LOWER

BRACKET-3R547

•
FLEXCOUPLING-3A525
^INTERMEDIATE

BRACKET-3676

VIEW AA

G1616-A

FIG. 11—Steering Column Installation—Ford, Mercury, Meteorprocarmanuals.com

03-06-03
Manual Steering

03-06-03

MAJOR REPAIR OPERATIONS

STEERING GEAR

DISASSEMBLY

1. Rotate the steering shaft 3 turns

from either stop.

2.
After removing the sector adjust-

ing screw locknut and the housing

cover bolts (Fig. 6), remove the sector

shaft with the cover. Remove the

cover from the shaft by turning the

screw clockwise. Keep the shim with

the screw.

HOUSING
•
3548
6. Turn the ball nut over, and ro-

tate the worm shaft from side to side

until all 50 balls have dropped out of

the nut into a clean pan. With the

balls removed, the ball nut will slide

off the worm.

7. Remove the upper bearing cup

from the bearing adjuster and the

lower cup from the housing. It may be

necessary to tap the housing or the

adjuster on a block of wood to jar the

bearing cups loose.

8. If the preliminary inspection

GASKET
• 3581

SHIM-3A657 COVER
AND

BUSHING
•
3583

SECTOR SHAFT

ADJUSTING SCREW
.
3577

•BEARING-3576

SEAL
- 3591

G 1623-A

FIG. 6—Sector Shaft
and
Housing Disassembled

-^-HOUSING-3548

BEARING
CUP •
3552

BALL
NUT

BEARING-3571

FILLER PLUG-3556
LOCK NUT-3707

3524 BEARING
CUP \
SEAL-3738

•GUIDE -3523

• BEARINGS
•
3647

.CLAMP-3544
BEARING
• 3571

G 1624-A

FIG. 7—Steering Shaft
and
Related Parts Disassembled

3.
Loosen the worm bearing adjust-

er nut, and remove the adjuster as-

sembly and the steering shaft upper

bearing (Fig. 7).

4.
Carefully pull the steering shaft

and ball nut from the housing, and i •-

move the steering shaft lower bearr g.

To avoid possible damage to the ball

return guides, keep
the
ball
nut
from

running down
to
either
end of the

worm.

Disassemble
the
ball only
if
there
is

indication
of
binding
or
tightness.

5.
Remove the ball return guide

clamp and the ball return guides from

the ball
nut.
Keep
the
ball
nut
clamp-

side up until ready to remove the

balls.
shows damage, press the sector shaft

bearing and the oil seal from the

housing (Fig. 8).

ASSEMBLY

1. If the sector shaft bearing and

oil seal have been removed, press a

new bearing into the housing and in-

stall a new oil seal. Do not clean,

wash or soak seals in cleaning solvent

(Fig.
7).
Apply
the
recommended

steering gear lubricant
to the
bearing

and seals.

2.
Install a bearing cup in the lower

end of the housing and in the adjuster.

3.
If the seal in the bearing adjuster

was removed, install a new seal.
Tool
-
T62F
•
3576
- A

G 1622-A

FIG.
8—Removing
Oil
Seal

and Bearing

4.
Insert the ball guides into the

holes of the ball nut, tapping them

lightly with a wood handle of a screw

driver if necessary to seat them.

5.
Insert 25 balls into the hole in

the top of each ball guide. It may be

necessary to rotate the shafi: slightly

one way, then in the opposite direc-

tion to distribute the balls in the cir-

cuit.

6. After the 50 balls are installed,

install the ball guide clamp. Torque

the screws to specification. Check the

worm shaft to make sure that it ro-

tates freely.

7. Coat the threads of the steering

shaft bearing adjuster, the housing

cover bolts, and the sector adjusting

screw with a suitable oil-resisi:ant seal-

ing compound. Do not apply sealer to

female threads and especially avoid

getting any sealer on the steering shaft

bearings.

8.
Coat the worm bearings, sector

shaft bearings, and gear teeth with

steering gear lubricant.

9. Clamp the housing in a vise, with

the sector shaft axis horizontal, and

position the steering shaft lower bear-

ing in its cup.

10.
Position the steering shaft and

ball nut assemblies in the housing.

11.
Position the steering shaft

upper bearing on the top of the worm,

and install the steering shaft bearingprocarmanuals.com