axle FORD MUSTANG 1969 Volume One Chassis

01-01-01
01-01-01

1

I 9Y82A848000
|
Y89A848000
rMMUNTrNUMBW

I 53A
A IA I8H 34 4

^J MODEL YEAR CODE

2)
ASSEMBLY PLANT CODE

5)
BODY SERIAL CODE

T)
ENGINE CODE

T)
CONSECUTIVE UNIT
NO.

T)
BODY TYPE CODE
(7)
COLOR CODE

0 TRIM CODE

® DATE CODE

(JO) DISTRICT-SPEC. EQUIP. CODE

(lT) REAR AXLE CODE

(12) TRANSMISSION CODE

W1001-A

Fig.
1—Warranty
Plates—Passenger Cars

9Y83NI0000I

Fig. 2—Typical Vehicle Identification Number
(VIN) Tab

W
1002-Aprocarmanuals.com

01-01-02
Vehicle Identification
01-01-02

VEHICLE WARRANTY NUMBER

The vehicle warranty number is the first line of numbers and

letters appearing on the Warranty Plates (Fig. 1). The Warranty

Plate is riveted to the left front door lock face panel. The first

number indicates the model year. The letter following the model

year number indicates the manufacturing assembly plant. The next

two numbers designate the Body Serial Code followed by a letter

expressing the Engine Code. The group of six digits remaining on

the first line indicate the Consecutive Unit Number.

VEHICLE DATA

The vehicle data appears on the second or lower line on the

Warranty Plate. The first two numbers and a letter identify the

Body Style. A letter or a number appears next indicating the

Exterior Paint Color followed by a number-letter combination

designating the Interior Trim. To the right of this code appears the

Date Code indicating the date the car was manufactured. A two-

digit number next designates the district in which the car was

ordered and may appear in conjunction with a Domestic Special

Order or Foreign Special Order number when applicable. The final

two spaces indicate the Rear Axle Ratio (numbers for regular axles,

letters for locking-types) and the Transmission type (numbers for

manual,
letters for automatic).

OFFICIAL VEHICLE IDENTIFICATION NUMBER

The official Vehicle Identification Number (VIN) for title and

registration purposes is stamped on an aluminum tab that is riveted

to the instrument panel close to the windshield on the driver's side

of the car and is visible from outside (Fig. 2).

MODEL YEAR CODE

The number 9 designates 1969.

ASSEMBLY PLANT CODES
COUGAR

Code

Letter
Code

Letter

A

B

C

D

E

F

G

H

J

K
Atlanta
L

Oakville (Canada)
N

Ontario Truck
P

Dallas
R

.,
Mahwah
S

Dearborn
T

Chicago
U

Lorain
W

Los Angeles
X

Kansas City
Y

Z
Michigan Truck

Norfolk

Twin Cities

San Jose

.
(Pilot). ...Allen Park

Metuchen

Louisville

Wayne

St. Thomas

Wixom

St. Louis

BODY SERIAL AND STYLE CODES

The two-digit numeral which follows the assembly plant code

identifies the body series. This two-digit number is used in con-

junction with the Body Style Code, in the Vehicle Data, which

consists of a two-digit number with a letter suffix. The following

chart lists the Body Serial Codes, Body Style Codes and the model.

LINCOLN CONTINENTAL

Body Body

Serial Style

Code Code Body Type

82
53A
4-Door Sedan

80
65A
2-Door
Hardtop

CONTINENTAL MARK
III

Body Body

Serial Style

Code Code Body Type

89
65A
2-Door
Hardtop
Body

Serial

Code

91

92

93

94

91
Body

Style

Code

65A

76A

65B

76B

65C

® Bench Seat

MERCURY

Body

Serial

Code

44

46

48

45

40

41

42

54

56

58

63

66

68

65

63

66

68

60

61

72

72

74

74

76

76
Body

Style

Code

54A

65A

57A

76A

53M

65M

57M

54C

65B

57B

53F

65F

57 F

76F

53C

65C

57C

63G

63H

71B

71C

71F

71G

71E

71A

©Bench Seat
Body
Type

2-Door
Hardtop©

Convertible©

2-Door
Hardtop©

Convertible®

2-Door
Hardtop®
Model

Standard

XR-7 Luxury

Standard

©Split Bench ©Bucket Seats

Body Type

4-Door Sedan©

2-Door
Hardtop-Formal®

4-Door Hardtop®

Convertible®

CANADA ONLY

4-Door Hardtop Sedan®

2-Door
Hardtop-Formal®

4-Door Hardtop®

4-Door Sedan®

2-Door
Hardtop-Formal®

4-Door Hardtop®

4-Door Hardtop Sedan®©

2-Door
Hardtop-Formal®©

4-Door Hardtop®®

Convertible®®

4-Door Hardtop Sedan©

2-Door
Hardtop-Formal©

4-Door Hardtop©
Model

Monterey

Marquis

Monterey-Custom

Marquis

Brougham (Option)

2-Door
Hardtop (Tunnel Roof)®© Marauder

2-Door
Hardtop (Tunnel Roof)®®©

4-Door 2 Seat®

4-Door 3 Seat (Side Facing)®

4-Door
2
Seat®

4-Door 3 Seat (Side Facing)®

4-Door 2 Seat®©

4-Door 3 Seat (Side Facing)®©
Monterey Wagoi

Monterey-Custom Wagon

Marquis Colony Park

©Split Bench ©Bucket Seats

METEOR (CANADA)

Body

Serial

Code

20

21

23
Body

Style

Code

54A

54B

65B
Body Type

4-Door Sedan®

4-Door Sedan®

2-Door
Hardtop-Formal®
Model

Rideau

Rideau 500

30
54C
4-Door Sedan®

35
65C
2-Door
Hardtop-Formal®

35
65E
2-Door
Hardtop-Formal{5-33)®®

33
57C
4-Door Hardtop®

34
76C
Convertible®

34
76E
Convertible (S-33)®®
Montcalm

24
65F
2-Door
Hardtop-Formal®©

27
57F
4-Door Hardtop®®
LeMoyne

28
71B
Rideau 500-6 Passenger®

29
71C
Rideau 500-Dual Face Rear®

38
71E
Mo ntcalm-6 Passenger®

39
71A
Montcalm-Dual Face Rear®
Station Wagons.

©Bench Seat ©Splite Bench ©Bucket Seatsprocarmanuals.com

01-01-04

Vehicle Identification
01-01-04

BODY SERIAL AND STYLE CODES-(continued)

FAIRLANE

Body

Serial

Code

30

31

34

35

33

36

35

33

36

40

41

42

44

43

42

44

43

46

46

45

45

32

37

38

47

48

48

49

49
Body

Style

Code

65A

54A

54B

63B

65B

76B

63E

65E

76E

65C

54C

63F

65F

76F

63D

65D

76D

63B

63E

65A

65E

71D

71B

71E

66A

66B

66B

(Opt.)

66C

66D

©Bench Seat
Body Type

2-Door
Hardtop-formal®

4-Door
Sedan®

4-Door
Sedan®

2-Door
Hardtop—Fastback®

2-Door
Hardtop-formal®

Convertible®

2-Door
Hardtop—Fastback©

2-Door
Hardtop-Formal©

Convertible®

2-Door
Hardtop-Formal®

4-Door
Sedan®

r t

2-Door
Hardtop—FastbackCD

2-Door
Hardtop-Formal®

Convertible®

2-Door
Hardtop—Fastback®

2-Door
Hardtop-Formal®

Convertible®

2-Door
Hardtop-Fastback®

2-Door
Hardtop-Fastback®

2-Door
Hardtop-Formal®

2-Door
Hardtop-formal®

Fairlane®

Fairlane 500®

Fairlane Torino Squire®

Ranchero®

Ranchero 500®

Ranchero 500®

Ranchero®

Ranchero®
Model

Fairlane

Fairlane 500

Fairlane 500

Torino

Torino GT

Torino GT

Cobra

Station Wagons-4 Door

Ranchero

Ranchero

Ranchero GT

©Split Bench ©Bucket Seats

REAR AXLE RATIO CODES

Conventional
Limited-Slip

Ratio

1
J
2.50:1

2
K
2.75:1

3
L
2.79:1

4
M 2.801

5
N
2.83:1

6
0
3.00:1

7
P
3.10:1

8
Q
3.20:1

9
R
3.25:1

A
S
3.50:1

B
T
3.07:1

C
U
3.08:1

D
V
3.91:1

E
W
4.30:1

TRANSMISSION CODES

Code Type

1
3-Speed
Manual

5 4-Speed Manual-wide ratio (2.78 1st Gear)

6 4-Speed Manual-close ratio (2.32 1st Gear)

W Automatic (C4) (XP-3)

U Automatic (C6) (XPL)

Y Automatic (MX)

X Automatic (FMX)

Z Automatic (C6 Special) (XPL, Special)®

©For Police & trailer towing
-
Not available with bucket seats
ENGINE CODES

Code

U
6Cyl.

T
6Cyl.

2
6 Cyl.®

L 6 Cyl.

3
6 Cyl CD

V
6
Cyl."

5
.
6 Cyl CD

B .6
Cyl.

E
6
Cyl.

F
8
Cyl.

6 8 Cyl.®

D 8
Cyl.

H 8 Cyl.

M 8 Cyl.

Y 8
Cyl.

X 8 Cyl.©

S 8 Cyl.©

P 8 Cyl.®

8 Cyl.

8 Cyl.®

K 8
Cyl.

N
8
Cyl.

A 8
Cyl.

©Low Compression

©High Performance
Type

170
Cu.
In.
(IV)

200
Cu.
In.
(IV)

200
Cu.
In.
(IV)

250
Cu.
In.
(IV)

250
Cu.
In.
(IV)

240
Cu.
In.
(IV)

240
Cu.
In.
(IV)

240 Cu. In. (IV) Police

240 Cu. In. (IV) Taxi

302
Cu.
In.
(2V)

302
Cu.
In.
(2V)

302 Cu. In. (2V) Police & Taxi

351
Cu.
In.
(2V)

351
Cu.
In.
(4V)

390
Cu.
In.
(2V)

390Cu.ln.(2V)

390
Cu.
In.
(4V)

428 Cu. In. (4V) Police Interceptor

428
Cu.
In.
(4V)
CJ

428
Cu.
In.
(4V)
CJ

429
Cu.
In.
(2V)

429
Cu.
In.
(4V)

460
Cu.
In.
(4V)

©Premium Fuel ©Improved Performance

©Ram Air Induction

CONSECUTIVE UNIT NUMBER

Starting Serial Numbers—1969 Passenger Cars

100,001—Ford, Fairlane, Falcon, Mustang, Thunderbird

500,001 -Mercury, Montego,
Cougar,
Meteor

848,000—Lincoln Continental & Continental Mark
III

EXTERIOR PAINT COLOR CODES

Code
Reference

Number
Color

A

B

c

D

E

F

G

H

|

J

K

L
. .

M

N

p

Q

R

S.
.. .

T

u

v

W

X

Y

z

2.
..

3

4

6.
. .

7

8
..
1724-A
1

3059-A

3197-A

3303-A

3191-A

3065-A
. .

3203-A

..
,.2067-A

2041-A

3080-A

3204-A

3060-A

1619-A
..

921-A

3064-A

1624-A

3198-A
. .

3199-A

2008-A

1070-A

3201-A

3120-A

3061-A
. . .

3202-A

2044-A

3071-A
. .

1730-A

3230-A

.
3077-A

3193-A

3190-A

..M6J-49B..

....M6J-50B.
Black

Maroon

Dk. Ivy Green Met.

Pastel Gray

Lt. Aqua

Dk. Aqua Met. (Brt.)

Med.
Orchid Met.

Lt. Green

Med.
Lime Met.

Dk. Aqua Met.

Dk. Orchid Met.

Lt. Gray Met.

White

Platinum

Med.
Blue Met.

Med.
Blue Met.

Lt. Gold

Med.
Gold Met.

Red

Med.
Aqua Met.

Lt. Aurora Copper IVIet.

Yellow

Dk. Blue Met.

Burnt Orange Met.

Dk. Grey Met.

Lt. Ivy Yellow

Calypso Coral

Med.
Emerald Met.

Med.
Blue Met. (Brt)

Lt. Emerald Green Met.

Lt. Blue

Red Primer

Grey Primerprocarmanuals.com

02-01-08
Brakes

02-01-08

BEARING CUP

DIMENSION "B"

0.755 MINIMUM

DIMENSION "A'

0.395 MINIMUM

H1532-B

FIG. 12—Disc Brake Rotor Service

Limits—Lincoln Continental

per splash shield or the bleeder screw

fitting.

4.
Front wheel bearing end play is

critical and must be within specifica-

tions.

5.
Be sure the vehicle is centered on

the hoist before servicing any front

end components, to avoid bending or

damaging the rotor splash shield on

full right or left wheel turns.

6. The proportioning valve should

not be disassembled or adjustments

attempted on it.

7.
Riding of the brake pedal (com-

mon on left foot applications) should

be avoided during vehicle operation.

8. The wheel and tire must be re-

moved ' separately from the brake

rotor, unlike drum brakes where the
wheel, tire and drum are removed as a

unit.

9. On floating caliper type disc

brakes whenever the caliper is re-

moved the caliper locating pins should

be inspected for wear or damage.

10.
On floating caliper type disc

brakes, the caliper assembly must be

removed from the spindle prior to re-

moval of the shoe and lining assem-

blies.

11.
On floating caliper type disc

brakes the calipers must not be inter-

changed from one side to the other.

When the caliper is installed on its

proper anchor plate and spindle, the

bleeder screw will point to the rear of

the vehicle (Fig. 22). If a caliper is in-

stalled on the wrong side of the vehi-

cle,
it is not possible to bleed the sys-

tem properly.

12.
Do not attempt to clean or re-

store oil or grease soaked brake lin-

ings.
When contaminated linings are

found, brake linings must be replaced

in complete axle sets.

DRUM BRAKES

1.
Remove the wheel from the

drum, and remove the drum as out-

lined in Part 2-2, Section 2.

2.
Brush all dust from the backing

plates and interior of the brake

drums.

3.
Inspect the brake shoes for ex-

cessive lining wear or shoe damage. If

the lining is worn within 1/32 inch of

the rivet heads or if the shoes are

damaged, they must be replaced. Re-

place any lining that had been con-

taminated with oil, grease or brake
fluid. Replace lining in axle sets. Prior

to replacement of lining, the drum di-

ameter should be checked to deter-

mine if oversize linings must be in-

stalled.

4.
Check the condition of brake

shoes,
retracting springs, hold-down

springs, and drum for signs of over-

heating. If the shoes have a slight blue

coloring, indicating overheating, re-

placement of the retracting and hold-.

down springs is strongly recommended.

Overheated springs lose their pull and

could cause the new lining i:o wear

prematurely, if they are not replaced.

5. If the vehicle has 30,000 or more

miles of operation on the brake linings

or signs of overheating are present

when relining brakes, the wheel cylin-

ders should be disassembled and in-

spected for wear and entrance of dirt

into the cylinder. The cylinder cups

should be replaced, thus avoiding fu-

ture problems.

6. Inspect all other brake parts and

replace any that are worn or dam-

aged.

7.
Inspect the brake drum and, if

necessary, refinish. Refer to Part 2-2,

Section 4 for refinishing.

BRAKE BOOSTER

Check the booster operation as

noted in Part 2-1, Section 1, Power

Brake Functional Test. If the brake

booster is damaged or defective, re-

place it with a new booster. The brake

booster is serviced only as an assem-

bly.procarmanuals.com

02-02-07
Brake System

02-02-07

ANTI-SKID CONTROL SYSTEM

RELEASE PAWL CAM PIN

RELEASE PAWL CAM LEVER

RELEASE CABLE

H
1636-
A

FIG. 10—Parking Brake Control Assembly

With Manual Release—Typical

power unit with mounting bracket is

riveted to the control assembly. The

vacuum actuated piston within the

unit is connected by a rod to the

upper end of the release lever (Fig. 9).

The lower end of the release lever ex-

tends out for alternate manual release
in the event of vacuum power failure

or for optional manual release at any

time.

Hoses connect the power unit and

the engine manifold to a vacuum re-

lease valve in the transmission neutral

safety switch.
The anti-skid control system con-

sists of three major components (Fig.

39).
Mechanically driven electromag-

netic sensors at each rear wheel; an

electronic control module mounted

under the glove box; a vacuum pow-

ered actuator attached to a bracket on

the inside of the right front frame rail

under the toe board.

The sensors consist of steel rings

having teeth on their outer diameters,

pressed on each axle shaft just out-

board of the wheel bearing. The teeth

rotate past corresponding teeth on the

inside diameter of stationary steel

rings mounted in the bearing retain-

ers.
Also mounted in the retainers, are

ring-shaped permanent magnets and

coils of wire. Two wires from each

sensor connect the sensors to the con-

trol module.

The control module consists of solid

state electronic components sealed in

a container. It is connected to the sen-

sors and to a solenoid on the actuator.

The actuator is similar to a vacuum

brake booster and consists of three

parts.
A chamber divided by a vacuum

suspended diaphragm; a hydraulic cyl-

inder connected to the diaphragm; and

a solenoid connected electrically to the

control module.

IN-VEHICLE ADJUSTMENTS AND REPAIRS

After any brake service work, ob-

tain a firm brake pedal before moving

the vehicle. Riding the brake pedal

(common on left foot application)

should be avoided when driving the

vehicle.

BRAKE SHOE ADJUSTMENTS—

DRUM BRAKES

The hydraulic drum brakes are

self-adjusting and require a manual

adjustment only after the brake shoes

have been relined, replaced, or when

the length of the adjusting screw has

been changed while performing some

other service operation. The manual

adjustment is performed with the

drums removed, using the tool and the

procedure detailed below.

When adjusting the rear brake

shoes,
check the parking brake cables

for proper adjustment. Make sure that

the equalizer operates freely.
To adjust the brake shoes:

1.
Use Rotunda Tool HRE 8650,

(Fig. 11) to determine the inside diam-

eter of the drum braking surface.

2.
Reverse the tool as shown in Fig.

11 and adjust the brake shoe diameter

to fit the gauge. Hold the automatic

adjusting lever out of engagement

while rotating the adjusting screw, to

prevent burring the screw slots. Make

sure the adjusting screw rotates freely.

If necessary, lubricate the adjusting

screw threads with a thin, uniform

coating of MIC-100-A.

3.
Rotate Tool HRE 8650 around

the brake shoes to be sure of the set-

ting.

4.
Apply a small quantity of high

temperature grease to the points

where the shoes contact the backing

plate, being careful not to get the lu-

bricant on the linings.

5. Install the drums. Install Tinner-

man nuts and tighten securely.

6. Install the wheels on the drums
and tighten the nuts to specification.

7.
Complete the adjustment by

applying the brakes several times with

a minimum of 50 lbs pressure on the

pedal while backing the vehicle. After

each stop the vehicle must be moved

forward.

8. After the brake shoes have been

properly adjusted, check the operation

of the brakes by making several stops

while operating in a forward direction.

WHEEL CYLINDER REPAIR-

DRUM BRAKE

Wheel cylinders should not be di-

sassembled unless they are leaking or

unless new cups and boots are to be

installed. It is not necessary to remove

the brake cylinder from the backing

plate to disassemble, inspect, or hone

and overhaul the cylinder. Removal is

necessary only when the cylinder is

damaged or scored beyond repair.procarmanuals.com

02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

BOOT

PISTON
. BLEEDER .

CYLINDER
SCREW RETURN SPRING PIST0N

H1385-B

FIG. 72—Brake Wheel Cylinder—Typical

DISASSEMBLY

1.
Remove the links and the rubber

boots from the ends of the brake cyl-

inder. Remove the pistons, cups, and

return spring from the cylinder bore

(Fig. 12).

2.
Remove the bleeder screw from

the cylinder.

INSPECTION

1.
Wash all parts in clean brake

fluid. Dry with compressed air.

2.
Replace scored pistons. Always

replace the rubber cups and dust

boots.
3.
Inspect the cylinder bore for

score marks or rust. If either condi-

tion is present the cylinder bore must

be honed. However, the cylinder

should not be honed more than 0.003

inch beyond its original diameter.

4.
Check the bleeder hole to be sure

that it is open.

ASSEMBLY

1.
Apply a light coating of heavy-

duty brake fluip! to all internal parts.

2.
Thread the bleeder screw into the

cylinder and tighten securely.

3.
Insert the return spring, cups,

and pistons into their respective posi-

tions in the cylinder bore (Fig. 12).
Place a boot over each end of the cyl-

inder. Bleed the brake system.

HYDRAULIC LINE REPAIR

Steel tubing is used throughout the

brake system with the exception of the

flexible hoses at the front wheels and

at the fear axle housing brake tube

connection (Figs. 17 thru 21).

Always bleed the applicable pri-

mary or secondary brake system after

primary or secondary brake system

hose or line replacement. Centralize

the pressure differential valve after

bleeding the system.

BRAKE TUBE

REPLACEMENT

If a section of the brake tubing be-

comes damaged, the entire section

should be replaced with tubing of the

same type, size, shape and length.

Copper tubing should not be used in a

hydraulic system. When bending

brake tubing to fit underbody or rear

axle contours, be careful not to kink

or crack the tube.

All brake tubing should be double

flared properly to provide good leak-

proof connections. Clean the brake

tubing by flushing with clean brake

fluid before installation.

When connecting a tube to a hose,

tube connector, or brake cylinder,

tighten the tube fitting nut to specified

torque with Milbar tool 1112-144 or

equivalent.

BRAKE HOSE

REPLACEMENT

A flexible brake hose should be re-

placed if it shows signs of softening,

cracking, or other damage.

When installing a new front brake

hose,
position the hose to avoid con-

tact with other chassis parts. Place a

new copper gasket over the hose fit-

ting and thread the hose assembly into

the front wheel cylinder. Engage the

opposite end of the hose to the brack-

et on the frame. Install the horsesho-

e-type retaining clip, and connect the

tube to the hose with the tube fitting

nut (Figs. 17 thru 21).

A rear brake hose should be in-

stalled so that it does not touch the

muffler outlet pipe or shock absorber.

Thread the hose into the rear brake

tube connector. Engage the front end

of the hose to the bracket on the

frame. Install the horseshoe-type re-

taining clip, and connect the tube to

the hose with the tube fitting nut.procarmanuals.com

02-02-09
Brake System

02-02-09

REMOVAL AND INSTALLATION

FRONT BRAKE DRUM

REMOVAL

1.
Raise the vehicle until the wheel

and tire clear the floor. Remove the

wheel cover or hub cap, and remove

the wheel and tire from the drum.

2.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

3.
Pull the drum off the wheel

spindle.

4.
If the drum will not come off,

pry the rubber cover from the brake

backing plate. Insert a narrow screw-

driver through the slot and disengage

the adjusting lever from the adjusting

screw. While holding the adjusting

lever away from the screw, back off

the adjusting screw with the brake ad-

justing tool (Fig. 13). Be very careful

not to burr, chip, or damage the

notches in the adjusting screw; other-

wise the self-adjusting mechanism will

not function properly.

INSTALLATION

1.
If the drum is being replaced, re-

move the protective coating from the

new drum with carburetor degreaser.

Then, use sandpaper to insure that no

residue remains. Wipe the drum with

a cloth soaked with denatured alcohol.

Install new bearings and grease seal.

Pack the wheel bearings, install the

inner bearing cone and roller assembly

RUBBER PLUG

REMOVED

'MOVE HANDLE UPWARD

TO RETRACT BRAKE SHOES
in the inner cup, and install the new

grease seal see Part 3-5, Section 4.

If the original drum is being in-

stalled, make sure that the grease in

the hub is clean and adequate.

2.
Adjust the brakes and install the

drum assembly as outlined under

Brake Shoe Adjustments in this sec-

tion.

3.
Install the outer wheel bearing,

washer and adjusting nut.

4.
Adjust the wheel bearing as out-

lined in Part 3-7, Section 2, then in-

stall the grease cap. Install the wheel

and hub cap.

REAR BRAKE DRUM

REMOVAL

1.
Raise the vehicle so that the tire

is clear of the floor.

2.
Remove the hub cap and wheel.

Remove the three Tinnerman nuts and

remove the brake drum. If the drum

will not come off, pry the rubber

cover from the backing plate. Insert a

narrow screwdriver through the hole

in the backing plate, and disengage

the adjusting lever from the adjusting

screw. While holding the adjusting

lever away from the adjusting screw,

back off the adjusting screw with the

brake adjusting tool (Fig. 13). Be very

careful not to burr, chip, or damage

the notches in the adjusting screw;

otherwise, the self-adjusting mecha-

nism will not function properly.

INSTALLATION

1.
Remove the protective coating

from a new drum with carburetor de-

greaser; then sand lightly and wipe

with a cloth soaked with denatured al-

cohol.

HI 590-A
H1390-A

FIG. 73—Backing Off Brake

Adjustment
FIG. 14—Retracting Spring

Removal
2.
Adjust the brakes as outlined

under Brake Shoe Adjustments in this

section. Place the drum over the brake

assembly and into position.

3.
Install the three Tinnerman nuts

and tighten securely. Install the wheel

on the axle shaft flange studs against

the drum, and tighten the attaching

nuts to specifications.

BRAKE SHOES AND

ADJUSTING SCREW-

DRUM BRAKES

REMOVAL

1.
With the wheel and drum re-

moved install a clamp over the ends of

the brake cylinder as shown in Fig.

14.

2.
Remove the secondary shoe to

anchor spring with the tool shown in

Fig. 14. With the same tool remove

the primary shoe to anchor spring and

unhook the cable eye from the anchor

pin.

3.
On Ford, Mercury, Meteor,

Thunderbird, Continental Mark III

and Lincoln Continental models, re-

move the shoe guide (anchor pin)

plate (Fig. 8).

4.
Remove the shoe hold-down

springs, shoes, adjusting screw, pivot

nut, socket and automatic adjustment

parts.

5.
On rear brakes, remove the

parking brake link and spring. Dis-

connect the parking brake cable from

the parking brake lever.

*>.
After removing the rear brake

secondary shoe, disassemble the park-

ing brake lever from the shoe by re-

moving the retaining clip and spring

washer (Fig. 8).

INSTALLATION

1.
Before installing the rear brake

shoes,
assemble the parking brake

lever to the secondary shoe and secure

with the spring washer and retaining

clip.

2.
Apply a light coating of high-

temperature grease at the points

where the brake shoes contact the

backing plate.

3.
Position the brake shoes on the

backing plate and secure the assembly

with the hold down springs. On the

rear brake, install the parking brake

link and spring, back off the parkingprocarmanuals.com

02-02-12
Brake System

02-02-12

TUBE ASSY. REF.

2 A 040

TUBE ASSY. REF.

2B113-B

PRESSURE

IMPULSE VALVE

PROPORTIONING
TUBE

>Y.
2B253 ASSY REF TUBE

/W W '
Kth#
2263 ASSY. R.H. REF.

TUBE

2B112-E
2264 ASSY. L.H. REF.

2B329

ASSY. REF.

HOSE

C8OA-2B218-C ASSY.L.H.

C80A-26171-D ASSY.R.H.

2B269 ASSY. REF.

VIEWZ

INSTALLATION-DISC BRAKE ONLY
BEND CLIP TO RETAIN

TUBE AS SHOWN
-TUBE

VIEW IN CIRCLE T

382365-S36
WASHER

8M-2149

TUBE-2A040
INSTALLATION-DISC BRAKES SAME AS

DRUM BRAKES AND MAIN VIEW

EXCEPT AS SHOWN
TUBE-2267 R.H.

TUBE-2B253

TUBE 2B329

PRESSURE DIFFERENTIAL

VALVE

TUBE 2B329

VIEW IN

CIRCLE U

TYPICAL ^,

CES^^
CLI

BOLT-

VIEW IN CIRCLE N
WASHER

34808-S8

PART OF AXLE

VENT ON STATION

WAGON ONLY

VENT ASSEMBLY

TUBE ASSEMBLY-2265

STANDARD AND POWER DRUM

3RAKES TUBE ASSEMBLY-2B1T2

POWER DISC BRAKES

MANUAL DISC

TUBE-2263 R.H.
3 REQUIRED

BOLT- 3 REQUIRED

CHECK BRAKE HOSE CLEARANCE „

TO ALL COMPONENTS IN
2A448"

METAL/METAL JOUNCE AND

METAL/METAL REBOUND-
TUBE-2267

ARMOR-390, 428 ENGINES ONLY

8 CYLINDER ENGINE REAR AXLE ONLY

TUBE ASSEMBLY-2268 L.H.

PRESSURE DIFFERENTIAL

VALVE

- GROMMET- 2

jl^REQUIRED

EWYN

TUBE
VIEW P

ROUTING FOR STATION WAGON ONLY

TUBE-22.S5

TUBE-2263 R.H. 2264 L.H.

VIEW IN CIRCLE Y

TYPICAL 2 PLACES
CHECK BRAKE HOSE CLEARANCE TO ALL

COMPONENTS IN METAL/METAL JOUNCE,

METAL/METAL REBOUND AND FULL

INSIDE AND OUTSIDE TURNS

VIEWX

TYPICAL 2 PLACES

DRUM BRAKES

TUBE-2263 R.H

2264 L.H.
VIEW IN CIRCLE U

TYPICAL 4 PLACES

HOSE-2A448

BRAKE HOSE-2078

GASKET-2149 2 REQUIRED

VIEW IN CIRCLE W

TYPICAL 2 PLACES

DRUM BRAKES
LIP
REINFORCEMENT ASSEMBLY-2B222

APPLY ESB-M4632-A SEALER AROUND

STUDS AND SCREW HOLE ON

FLOOR PAN SIDE

TUBE
TUBE ASSEMBLY-226J)

VIEW R

TUBE

VIEW IN CIRCLE M

POWER DISC BRAKES

BRAKE HOSE MUST BE ASSEMBLED

WITH WHEELS STRAIGHT AHEAD.

STRIPE ON HOLE HOSE ASSEMBLY

MUST SHOW NO EVIDENCE OF TWIST.

H 1559-C

—Service Brake
System—Fairlane,
Montego
and
Falconprocarmanuals.com

TUBE ASSEMBLY-2B255

VIEW IN CIRCLES V

FUEL LINE

CLIP (4 REQUfRED)
PART OF AXLE ASSEMBLY

HOSE ASSEMBLY-2A448

FRAME

TUBE ASSEMBLY-2267

CHECK BRAKE HOSE

CLEARANCE TO ALL

COMPONENTS IN

METAL/METAL JOUNCE

AND METAL/METAL

REBOUND.
CLIP (3 REQUIRED)

TUBE ASSEMBLY-2267

BRAKE BOOSTER-2B195

HOSE-2A047
TUBE ASSEMBLY-2B255

TUBE ASSEM3LY-2420

[

TUBE-2263-C *
TUBE ASSEMBLY BRAKE TUBE

2268 ASSEMBLY

2267 R.R. BRAKE TUBE

ASSEMBLY
TUBE ASSEMBLY

2263

VIEW IN CIRCLES X

COVER-2A487

PEDAL PAD-2457

BRAKE PEDAL-2455

USE EXISTING NUTS

TUBE ASSEMBLY

2325r
TUBE ASSEMBLY

2264 L.H. 2263 R.H.
TUBE ASSEMBLY

2B171-C R.H.

23218-C L.H.
BOLT-381877-S2

(3REQUIRED)

CLIP-382088-S2

(3 REQUIRED)

ALL CONNECTIONS, TUBES, MASTER

CYLINDER AND FITTINGS MUST BE

FREE OF FLUID LEAKAGE WHEN

CHECKED AFTER ROAD TEST.
TUBE ASSY.-2A040

TUBE ASSY.-2B253
PRESSURE IMPULSE

VALVE

ALL BRAKE LINES, FITTINGS AND

FLEXIBLE HOSES MUST BE KEPT FREE

OF FOREIGN MATERIAL BEFORE

AND DURING ASSEMBLY OPERATIONS.
TUBE ASSEMBLY

2B255

PROPORTIONING

VALVE-2B328
GASKET-2149

(4 REQUIRED)

#LUBRICATE PIVOTS

CLIP-381799-S2

2REQUIRED

180°APART
BE LEAKPROOF

TUBE ASSEMBLY-2B255
6

w

Q

7T

3

CHECK BRAKE HOSE

CLEARANCE TO ALL COMPONENTS

IN METAL/METAL JOUNCE

METAL/METAL REBOUND AND FULL

INSIDE AND OUTSIDE TURNS.

BOLT

2 REQUIRED

TUBE ASSY. -2264

BRACKET ASSY.-2B328
O

6

H 1540-C

FIG. 20—Service Brake System—Thunderbird, Continental Markprocarmanuals.com

02-02-16
Brake System

02-02-16

fitting that connects the tube to the

cylinder. Do not pull the metal tube

away from the cylinder. Pulling the

tube out of the cylinder connection

will bend the metal tube and make in-

stallation difficult. The tube will sepa-

rate from the cylinder when the cylin-

der is removed from the backing

plate.

4.
On all except the front wheels on

Ford, Mercury, and Meteor models,

remove the wheel cylinder attaching

bolts and lock washers and remove the

cylinder. On the front wheel of Ford,

Mercury and Meteor models, remove

the nut and washer that attaches the

cylinder to the anchor pin. Remove

the cylinder from the anchor pin.

INSTALLATION

Wipe the end(s) of the hydraulic

line to remove any foreign matter be-

fore making connections.

1.
On all models except Ford, Mer-

cury and Meteor, to install a front

wheel cylinder, position the cylinder to

the backing plate. Install the two lock

washers and attaching bolts. Torque

them to specifications.

On Ford, Mercury and Meteor

models, to install a front wheel cylin-

der, position the cylinder on the an-

chor pin against the backing plate. In-

stall the washer and cylinder attaching

nut on the anchor pin, and torque it

to specification. Lock the washer re-

tainer securely.

2.
Install a new copper gasket over

the hose fitting. Thread the hose into

the cylinder and tighten it to specified

torque.

3.
Engage the opposite end of the

hose to the bracket on the frame. In-

stall the horseshoe-type retaining clip,

and connect the brake tube to the

hose with the tube fitting nut. Tighten

the nut to specification with tool

1112-144.

4.
To install a rear wheel cylinder,

place the rear wheel cylinder into po-

sition. Enter the tubing into the cylin-

der, and start the tube fitting nut into

the threads of the cylinder.

5.
Secure the cylinder to the back-

ing plate by installing the attaching

bolts and lock washers.

6. Tighten the tube fitting nut to

specification with tool 1112-144.

7.
Install the links in the ends of

the wheel cylinder, install the shoes

and adjuster assemblies, and adjust

the shoes as outlined in this section.

8. Adjust the brakes (Part 2-2, Sec-

tion 2). Install the brake drum and

wheel. Bleed the brakes and centralize

the differential valve as outlined in

Part 2-1, Section 2.
BRAKE BACKING PLATE

DRUM BRAKE

REMOVAL

1.
Remove the wheel and brake

drum. Disconnect the brake line from

the brake cylinder.

2.
Remove the brake shoe and ad-

juster assemblies and the wheel cylin-

der as outlined in this section. On the

rear wheels, disconnect the parking

brake lever from the cable.

3.
If the rear backing plate is being

replaced, remove the axle shaft from

the applicable rear axle as outlined in

Group 4, Part 4-2— Rear Axle, Sec-

tion 2, disengage parking brake cable

retainer from backing plate. Remove

the backing plate and gasket.

If the front backing plate is being

replaced, remove the bolts and nuts

that secure the backing plate to the

front wheel spindle and remove the

plate and gasket.

INSTALLATION

If a rear backing plate is to be re-

placed, position a new rear backing

plate and gasket on the attaching

bolts in the axle housing flange. Insert

parking brake cable into backing plate

and secure retaining fingers. Install

the rear axle shaft for applicable rear

axle.
Refer to Group 4, Part 4-2 —

Rear Axle, Section 2 for the proper

installation procedure.

1.
If the front brake backing plate

is to be replaced, position a new front

backing plate and gasket to the wheel

spindle and install the attaching bolts

and nuts.

2.
Install the wheel cylinder and

connect the brake line as outlined in

this section.

3.
Install the brake shoe and ad-

juster assemblies as outlined in this

section. On a rear brake, connect the

parking brake cable to the lever.

4.
Adjust the brake shoes (Section

2),
and install the brake drums and

wheels. Bleed the brake system and

centralize the differential valve as out-

lined in Part 2-1, Section 2.

DISC BRAKE CALIPER

ASSEMBLY

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

Refer to Figs. 22 and 23.
BLEEDER SCREW FACING THIS DIRECTION^

BLEEDER SCREW

H 1641-A

FIG. 22—Floating Caliper

Installed

1.
Remove the front wheel cover.

Remove the wheel and tire assembly

from the hub and rotor assembly. Be

careful to avoid damage or interfer-

ence with the caliper splash shield or

bleeder screw fitting.

2.
Disconnect the brake line from

the caliper. Cap the hose to prevent

*he brake fluid from leaking from the

master cylinder.

3.
Remove the safety wire and the

two bolts that attach the caliper as-

sembly to the spindle.

4.
Lift the caliper assembly off the

rotor and place it on the bench.

Installation

1.
Position the caliper assembly on

the rotor, and mate the mounting bolt

holes in the caliper with those in the

spindle. It may be necessary to push

the caliper piston into the cylinder

bore to obtain clearance between the

shoe and lining assembly and the

rotor.

2.
Install the caliper to spindle at-

taching bolts and torque them to spe-

cification. The upper bolt must be

tightened first. Install the safety wire

on the bolts and twist the wire ends at

least five turns. Push the wire ends

against the spindle to avoid interfer-

ence with the brake hose and the

steering stop. Check to insure that the

rotor runs squarely and centrally be-

tween the two brake shoes.

3.
Position the brake hose fitting

with a new copper washer on each

side of the fitting on the caliper as-

sembly. Install the bolts and torque to

specification.

4.
Bleed the brake system and cen-

tralize the differential valve as out-

lined in Part 2-1. Check the masterprocarmanuals.com