belt FORD MUSTANG 1969 Volume One Chassis

03-01-02
Suspension — Steering, Wheels And Tires — General Service

03-01-02

1 TESTING

POWER STEERING-

PRELIMINARY TESTS

The following preliminary checks

should always be made before per-

forming any operations.

AIR BLEEDING

Air in the power steering system

(shown by bubbles in the fluid) should

be bled. After making sure that the

reservoir is filled to specification (the

fluid must be at normal operating

temperature when the check is made),

turn the steering wheel through its full

travel three or four times. Do not hold

the wheels against their stops. Re-

check the fluid level.

CHECK FLUID LEVEL

Run the engine until the fluid is at

normal operating temperature. Then

turn the steering wheel all the way to

the left and right several times, and

shut off the engine.

Check the fluid level in the power

steering reservoir. The level must show

on the cross hatching between the bot-

tom of the dipstick and the full mark

(Fig. 1). If the level is low, add

enough automatic transmission fluid

C1AZ-19582-A to raise the level to

the F mark on the dipstick. Do not

overfill the reservoir.

CHECK PUMP BELT

If the pump belt is broken, glazed,

or worn, replace it with a new belt.

Use only the specified type of belt.

Refer to Part 3-13 for belt adjustment

procedure.

CHECK FOR FLUID

LEAKS

With the engine idling, turn the

steering wheel from stop to stop sever-

al times. Check all possible leakage

points. Tighten all loose fittings, and

replace any damaged lines or defective

seats.

CHECK TURNING EFFORT

With the front wheels properly al-

igned and tire pressures correct, check

the effort required to turn the steering

wheel.
G 1508- A

FIG.
1—Power
Steering Pump

Dipstick

1.
With the vehicle on dry concrete,

set the parking brakes.

2.
With the engine warmed up and

running at idle speed, turn the steering

wheel to the left and right several

times to warm the fluid.

3.
Attach a pull scale to the rim of

the steering wheel. Measure the pull

required to turn the wheel one com-

plete revolution in each direction. The

effort required to rotate the steering

wheel should not exceed specifications

given in Part 3-13.

POWER STEERING PUMP FLOW

AND PRESSURE TESTS—

EXCEPT LINCOLN CONTINENTAL

AND CONTINENTAL MARK III

The power steering flow and pres-

sure tests will show whether the pump,

steering gear or power assist control

RETURN LINE

POWER

STEERING PUMP

Sr
valve is causing the trouble. Steps out-

lined below should be followed to de-

termine the cause of the trouble.

PUMP FLOW TEST

1.
Depending on the equipment

present on the vehicle (air condition-

ing, power brakes, standard transmis-

sion),
one of the following options

may be used to connect the pump

pressure and return hoses to the test

tool (T56L-3361O-D and T68L-

33610-A):

a. Disconnect the pressure and re-

turn lines at the power steering pump

(Fig. 2). Obtain a power steering re-

turn hose from stock and connect the

end with the fitting to the output fit-

ting of the tool using the
5/8-18
SAE

female, 1/4 N.P. thread male fitting

provided. The end of the stock hose

(without the fitting) should be con-

nected to the return tube of the pump.

Connect the pressure hose from the

tool to the outlet fitting of the pump.

b.
Disconnect the pressure line at

the pump and connect the pressure

line from the test tool to the outlet fit-

ting of the pump. Disconnect the re-

turn line at the gear and connect it to

the output fitting of the tool, using the

5/8-18
SAE female, 1/4 N.P. thread

male fitting provided.

2.
After installing the lines by the

most advantageous method, proceed

as follows:

3.
Open the manual valves A and B

fully (Fig. 2).

CALIBRATED FLOW

DETERMINING ORIFICE

PRESSURE LINE

FIG. 2—Power Steering Pump Test Circuit Diagram
PRESSURE GAGE

G1611-Aprocarmanuals.com

03-07-01
Ford Design Non-Integral Power Steering System

03-07-01

PART
3-7
Ford Design Non-Integral Power

Steering System

COMPONENT INDEX

CONTROL VALVE

Disassembly
and
Overhaul

Removal
and
Installation

CONTROL VALVE CENTERING SPRING

Adjustment

CONTROL VALVE
TO
POWER STEERING

CYLINDER HOSE

Removal
and
Installation

HOISTING INSTRUCTIONS

POWER CYLINDER

Removal
and
Installation

POWER CYLINDER SEAL

Removal
and
Installation

POWER STEERING PUMP CLEANING

AND INSPECTION
(See
Part 03-01)

Removal
and
Installation

POWER STEERING PUMP
TO
CONTROL

VALVE HOSE

Removal
and
Installation

STEERING GEAR

Cleaning
and
Inspection

(See Part 03-01)
MODEL APPLICATION
All
Models
Ford

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Mercury
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Cougar
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
07-04

07-03

07-02

07-02

07-02

07-04

07-06

07-03

07-02
Falcon
07-04

07-03

07-02

07-02

07-02

07-04

07-06

07-03

07-02
Montego
07-04

07-03

07-02

07-02

07-02

07-04

07-06

07-03

07-02
Mustang
07-04

07-03

07-02

07-02

07-02

07-04

07-06

07-03

07-02
Lincoln-
Continental
07-04

07-03

07-02

07-02

07-02

07-04

07-06

07-03

07-02
Thunderbird
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Continental-
Mark
III
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that
the
item
is for the
vehicle listed
at the
head
of the
column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.

DESCRIPTION

The Ford Non-Integral Power

Steering System
(Fig. 1) is a
hydrauli-

cally controlled linkage-type steering

system which includes
an
integral

pump
and
fluid reservoir,
a
control

valve,
a
power cylinder,
the
connecting
fluid lines,
and the
steering linkage.

The hydraulic pump
and
belt, driven

from
the
engine crankshaft, draws

fluid from
the
reservoir
and
provides

fluid pressure
for the
system. Within

the pump itself
is a
pressure-relief
valve which governs
the
pressures

within
the
steering system according

to
the
varying conditions
of
operation.

After fluid
has
passed from
the
pump

to
the
control valve
and the
power
cyl-

inder,
it
returns
to the
reservoir.
procarmanuals.com

03-10-01

Ford-Thompson Power Steering Pump*

03-10-01

PART 3-10 Ford-Thompsonr Power Steering Pump

COMPONENT INDEX

PUMP BELT TENSION ADJUSTMENT

PUMP DRIVE BELT

Removal and Installation

POWER STEERING PUMP

Cleaning and Inspection (See Part 03-01)

Description

Disassembly and Assembly

Removal and Installation

POWER STEERING PUMP PULLEY

Removal and Installation

POWER STEERING PUMP RESERVOIR

Removal and Installation

ROTOR SHAFT SEAL

Removal and Installation
MODEL APPLICATION
All
Models
Ford

10-01

l5-O2

10-01

10-04

10-02

10-03

10-03

10-04
Mercury
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Meteor
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Cougar
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Fairlane
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Falcon
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Montego
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Mustang
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
10-01

10-02

10-01

10-04

10-02

10-03

10-03

10-04
Continental-
Mark
III
N/A

N/A

N/A

N/A

N/A

N/A

N/A

'N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

1
DESCRIPTION

The Ford-Thompson power steering

pump is a belt driven slipper type

pump which is integral with the reser-
voir (Fig. 1). It is constructed so that

the reservoir is attached to the rear

side of the pump housing front plate
and the pump body is encased within

the reservoir (Fig. 2).

IN-VEHICLE ADJUSTMENTS AND REPAIRS

PUMP BELT TENSION

ADJUSTMENT

Pump drive belt tension cannot be

checked accurately using the
•
thumb

pressure or belt deflection methods.

Correct belt adjustment is assured

only with the use of a belt tension

gauge.

1.
Check the belt tension with a

belt tension gauge tool T63L-8620-A.

With a new belt, or one that has been

run for less than 15 minutes, the ten-

sion should be within 120-150 lbs.

With a belt that has been run for

more than 15 minutes, the tension

should be within 90-120 lbs.

2.
To adjust the belt, loosen the

mounting bolts incorporated on the

front face of the pump cover plate

(hub side) and one nut at the rear of

the reservoir. Fix a 9/16 inch open

end wrench on the nrojecting 1/2 inch

boss on the cover -'plate a"hd pry up-

ward to correct tension on 6 cyl. en-

gines.
DIPSTICK.

DRIVE

PULLEY

RELIEF VALVE

RESERVOIR

ORIFICE PLUG

G1479-B

FIG.
1—Power
Steering Pump—Sectional View
procarmanuals.com

03-10-02

Ford-Thompson Power Steering Pump

03-10-02

LOWER PRESSURE

PLATE 3D590

SPRING-3D601

UPPER PRESSURE

PLATE -3A645

RETAINER END

PLATE-3D589

CAM AND ROTOR

ASSEMBLY-
-3D607

SCREW AND WASHER

ASSEMBLY-379376-S
PULLEY-3D673

PUMP SHAFT

SEAL 3B592

PLATE AND BUSHING

ASSEMBLY-3D643

0-RING

382744-S

HOUSING GASKET

3A760

G1343-B

FIG. 2—Power Steering Pump Disassembled

To adjust the belt on 8 cyl. engines

loosen the mounting bolt in the ad-

justing slot and the nut directly above

the adjusting slot. Place a suitable pry

bar between the cast boss on the

pump mounting bracket and the cast

boss on the pump cover plate and pry

upward to correct tension.

Do not pry against the reservoir to

obtain proper belt load as it can be

deformed and cause a leak.

3.
Recheck the belt tension. When

the tension has been correctly adjusted,
tighten the bolts and the fiut to speci-

fication (Part 3-13).

POWER STEERING

PUMP DRIVE BELT

REPLACEMENT

1.
Loosen the idler pulley attaching

bolts and remove the compressor drive

belt if equipped with an air condition-

er.

2.
Loosen 3 bolts and one nut at-
taching the power steering pump to

the pump bracket, and remove the

pump drive belt.

3.
Position the power steering

pump drive belt on the pulleys.

4.
Adjust the drive belt tension as

outlined in Section 2 to specification

(Part 3-13) and tighten the pump at-

taching bolts and one nut to specifica-

tion.

5.
Install the compressor drive belt

if equipped with an air conditioner

and adjust to specification (Part 16).

REMOVAL AND INSTALLATION

POWER STEERING

PUMP REPLACEMENT

EIGHT CYLINDER

WITHOUT AIR

CONDITIONER AND

ALL SIX CYLINDER

1.
Remove the power steering fluid

from the pump reservoir by discon-

necting the fluid return hose at the

reservoir, and allow the fluid to drain

into a suitable container.

2.
Disconnect the pressure hose
from the pump.

3.
Remove 3 bolts from the front of

the pump and the one nut at the rear

(rear nut on 8 cyl. engines only) that

attach the pump to the mounting

bracket; disconnect the belt from the

pulley and remove the pump from the

vehicle.

4.
Position the pump to the mount-

ing bracket and install the 3 bolts at

the front of pump and (rear nut on 8

cyl.
engines only) the 1 nut at the

rear. Torque to specification.

5.
Place the belt on the pulley and

adjust the belt tension (Section 2) with
Tool T63L-8620-A and tighten the

bolts and nut to specifications.

6. Torque the pressure hose fitting

hex nut to specification. Then, connect

the pressure hose to the fitting and

torque the hose nut to specification.

7.
Connect the hose to the pump.

Then, tighten the clamp.

8. Fill the power steering pump res-

ervoir with transmission fluid C1AZ-

19582-A and cycle the system to re-

move air from the steering gear sys-

tem.

9. Check for leaks and again check

the fluid level. Add fluid as necessary.procarmanuals.com

03-10-03
Ford-Thompson Power Steering Pump

03-10-03

EIGHT CYLINDER WITH

AIR CONDITIONER

1.
Remove the power steering fluid

from the pump reservoir by discon-

necting the fluid return hose from the

reservoir and allow the fluid to drain

in a suitable container.

2.
Disconnect the pressure hose

from the pump.

3.
Remove 3 bolts from the front of

the pump and the one nut at the rear

that attach the pump to the mounting

bracket and remove the drive belt

from the pump pulley.

4.
Loosen the upper pump bracket-

to-engine attaching bolt and remove

the bolt in the belt adjusting slot. Re-

move the pump.

5.
Position the pump to the bracket

and install the bracket-to-pump at-

taching bolts and nuts. Tighten to spe-

cifications.

6. Place the belt on the pump pul-

ley. Adjust the belt tension as outlined

in Section 2 and tighten the bolts and

nut to specification.

7.
Torque the pressure hose fitting

hex nut to specification. Then, connect

the pressure hose to the fitting and

torque the hose nut to specification.

8. Connect the return hose to the

power steering pump and tighten the

clamp.

9. Fill the pump with automatic

transmission fluid C1AZ-19582-A.

Bleed the air from the system (Part

3-1) and check for leaks and again
check the fluid level. Add fluid as re-

quired.

POWER STEERING PUMP

PULLEY REPLACEMENT

REMOVAL

1.
Drain as much of the fluid as

possible from the pump through filler

pipe.

2.
Install a 3/8-16 inch capscrew in

the end of the pump shaft to prevent

damage to the shaft end by the tool

screw.

3.
Install the pulley remover, Tool

T63L-1O3OO-B, on pulley hub, and

place the tool and pump in a vise as

shown in Fig. 3.

4.
Hold the pump and rotate the

tool nut counterclockwise to remove

the pulley (Fig. 3). The pulley must be

removed without in and out pressure

on the pump shaft to prevent damage

to internal thrust areas.

INSTALLATION

1.
Position the pulley to the pump

shaft and install Tool T65P-3A733-A

as shown in Fig. 4.

2.
Hold the pump and rotate the

tool nut clockwise to install the pulley

on the shaft. The pulley face will be

flush with end of pump shaft. Install

the pulley without in and out pressure
on the shaft to prevent damage to in-

ternal thrust areas.

3.
Remove the tool.

POWER STEERING PUMP

RESERVOIR REPLACEMENT

Reservoir replacement must be done

on a clean workbench. Cleanliness of

work area and tools is extremely im-

portant when repairing any hydraulic

unit. Thoroughly clean the exterior of

the pump with a suitable cleaning sol-

vent. Do not clean, wash or soak the

shaft oil seal in solvent. Plug the inlet

and outlet openings with plugs or

masking tape before cleaning the

pump exterior or removing the reser-

voir.

REMOVAL

1.
Assemble the adapter plate (Tool

T69P-3A674-A) to the bench mounted

fixture tool (T57L-5OO-A). Position

the pump and pulley on the adapter

plate, pulley facing down.

2.
Remove the outlet fitting hex nut

and the service identification tag.

3.
Invert the pump so the pulley is

facing up and remove the reservoir by

tapping around the flange with a wood

block (Fig. 5).

4.
Remove the reservoir O-ring seal

and the outlet fitting gasket from the

pump.

INSTALLATION

Tool • T 63 L-

10300 -

G 1477 A

FIG. 3—Removing Power

Steering Pump Pulley
1478 A

FIG. 4—Installing Power

Steering Pump Pulley
1.
Install a new gasket on the outlet

fitting and a new reservoir O-ring seal

on the pump housing plate (Fig. 6).

The old gasket and seal should never

be re-used.

Too/
T57L 500-A

G1602-A

FIG. 5—Removing Pump

Reservoirprocarmanuals.com

03-11-01
Eaton Power Steering Pump

03-11-01

PART 3-11 Eaton Power Steering Pump

COMPONENT INDEX
MODEL APPLICATION

3
§>
"o

4

POWER STEERING PUMP

Cleaning and Inspection (See Part 03-01)

Description

N/A
N/A
N/A
N/A
N/A
N/A

N/A
N/A
11-01

N/A
11-01

Disassembly and Overhaul

N/A
N/A

N/A
N/A

N/A
N/A

N/A
N/A
11-03

N/A
11-03

Removal and Installation

N/A
N/A
N/A
N/A

N/A
N/A
N/A
N/A
11-01
N/A

11-01

POWER STEERING PUMP RESERVOIR

Removal and Installation

N/A
N/A
N/A

N/A
N/A
N/A

N/A

N/A

11-01
N/A

11-01

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

l
DESCRIPTION

The roller-type hydraulic pump,

driven by the crankshaft, draws auto-

matic transmission fluid down the res-

ervoir and provides fluid pressure for

the system. Steering gear lubrication
is also provided by the same fluid

from the reservoir. Within the pump

itself is a flow-control and pressure-

relief valve which governs the pres-
sures within the steering system ac-

cording to the varying conditions of

operation. After fluid has passed from

the gear, it returns to the reservoir.

REMOVAL AND INSTALLATION

POWER STEERING PUMP

REMOVAL

1.
Open the hood, and install fend-

er covers.

2.
If the vehicle is equipped with air

conditioning, loosen the compressor

adjusting and support bracket bolts

and remove the drive belt.

3.
Loosen the generator adjusting

and support bracket bolts, and remove

the drive belts.

4.
Remove the fan, pulley, and spa-

cer.

5.
Raise the vehicle.

6. Remove the crankshaft damper

bolt and washer. Remove the damper

with Tool 6306-AG. Remove the drive

key.

7.
Disconnect the pump inlet line at

the pump, and plug the end of the line

to prevent the loss of fluid. Disconnect

the pump pressure line at the pump.
8. Remove the pump-to-engine

front cover cap screws, and remove

the pump. Remove the seal from the

front cover.

INSTALLATION

1.
Install a new seal on the engine

front cover.

2.
Align the slot in the pump rotor

shaft with the drive key in the crank-

shaft, and slide the pump onto the

shaft. Install the pump-to-engine front

cover cap screws. Torque the cap

screws to specification.

3.
Connect the pump inlet line and

the pressure line.

4.
Install the damper drive key,

damper, washer and bolt. Torque the

bolt to specification.

5.
Install the fan, pulley, and spa-

cer. Install the generator drive belts.

Adjust the belt tension, and tighten

the adjusting and support bracket

bolts.
6. If the vehicle is equipped with air

conditioning, install the compressor

drive belt. Adjust the belt tension, and

tighten the adjusting and support

bracket bolts.

7.
Run the engine at idle speed,

and check the fluid level in the reser-

voir. If required, add the specified au-

tomatic transmission fluid. Turn on

the windshield wipers. Rotate the

steering wheel from stop to stop sever-

al times to bleed the air from the sys-

tem. Recheck the fluid level.

POWER STEERING PUMP

RESERVOIR

WITHOUT AIR

CONDITIONING

Removal

1.
Remove the reservoir cover andprocarmanuals.com

03-11-02
Eaton Power Steering Pump

03-11-02

gasket. Withdraw the fluid with a suc-

tion gun.

2.
Remove the reservoir bracket-

to-cylinder block upper cap screw and

the lower cap screw and spacer.

3.
Disconnect the reservoir infet line

and the outlet line at the reservoir,

and remove the reservoir.

Installation

1.
Connect the reservoir-to-pump

line (outlet line) at the reservoir, but

do not tighten the clamp.

2.
Attach the reservoir and bracket

to the cylinder block with the upper

cap screw and the lower cap screw

and spacer. Tighten the cap screws.

3.
Tighten the outlet line clamp at

the reservoir. Connect the reservoir

inlet line to the reservoir.

4.
Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.
WITH AIR CONDITIONING

Removal

1. Raise the front of the vehicle.

Remove the reservoir-to-pump line

(outlet line) clamp at the reservoir,

but do not disconnect the line at this

time.

2.
Disconnect the reservoir inlet line

at the reservoir.

3.
Remove the reservoir bracket to

the cylinder block upper cap screw.

Support the reservoir and remove the

lower cap screw and spacer.

4.
With a drain pan under the res-

ervoir, disconnect the outlet line hose

from the reservoir tube and allow the

fluid to drain.

5.
Remove the reservoir cover re-

taining nut and the cover. Position the

cover and the reservoir out of the way

and allow them to rest in the engine

compartment.

6. Lower the front of the vehicle.

Remove the fan shroud.

7.
Remove the reservoir and the
cover by manipulating them through

the opening between the radiator and

the compressor drive belt.

Installation

1.
Position the reservoir in the en-

gine compartment. Loosely attach the

reservoir and bracket to the cylinder

block with the upper cap screw.

2.
Install the fan shroud, then raise

the front of the vehicle.

3.
Connect the reservoir-to-pump

line (outlet line) at the reservoir.

4.
Install the reservoir bracket-

to-cylinder block lower cap screw and

spacer. Tighten both the upper and

the lower cap screws.

5.
Connect the reservoir inlet line at

the reservoir. Install the clamps on

both lines. Lower the car, and install

the reservoir cover and attaching nut.

6. Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.

3 MAJOR REPAIR OPERATIONS

INSULATOR (2)

WASHER (2)

MOUNTING BOLT (2)

COVER

BOLT (7)
DOWEL
PIN (2)

ROTOR

ROTOR
SHAFT

COVER
SEAL
PLUG

O RING

VALVE
ASSEMBLY

VALVE
SPRING

INSULATOR

HOUSING

CAM RING

PRESSURE
PLATE
,
PUMP

i
HOUSING

SEAL

ROLL

PIN

INSULATOR

RETAINER
RING
TUBE SEAT

O RING

SCREW
(2)

G12O8-B

FIG.
1
— Power Steering Pumpprocarmanuals.com

03-13-02
Specifications

03-13-02

POWER STEERING PUMP

SERVICE
SPECIFICATIONS

Description

Pump Rotor Shaft End Play

Max. Torque Allowed
to

Rotate Rotor Shaft

Stamped Housing to Plate

Assy. Screw and Washer Assy.

Reservoir
to
Stamped Housing

Nut

Cam Ring to Pressure Plate

Screw

Housing to Cover Screw
Ford-Thompson

.017 in. Max.-.003 in. Min.

15 In-Lb.

28-32 Ft.-Lb.

43-47 Ft.-Lb.

_

-
Eaton

—

_

-

—

20 In-Lb.

15-20 Ft,-Lb.

FORD-THOMPSON POWER STEERING

PUMP
TORQUE
LIMITS (FT-LBS)

Description

Pump Rear Mounting Nut

Pressure Hose Nut

Pump Attaching Nuts

Bracket
to
Engine Attaching Nuts
6-Cyl.

302-351 CID

390,427,428,429 CID

Bracket
to
Cylinder Head

Belt Adjustment Bolt

Rear Support Bracket Attaching Nuts

Bracket
to
Engine Adapter

Engine Adapter
to
Engine

Engine Adapter
to
Pump
240 CID

170-200 CID

170-200 CID

250 CID

250 CID
Ford,
Mercury,

Meteor,

Thunderbird

14-18

20-30

25-35

1216

18-25

30-40

25-35

-

45-60

-

-

-

-
Cougar, Falcon,

Fairlane, Montego,

Mustang

20-30

20-30

30-40

7-10

18-25

30-40

25-35

25-35

-

25-35

17-25

30-40

25-35

INTEGRAL
POWER
STEERING GEAR SPECIFICATIONS

Description

Type

Ratio

Turns of Steering Wheel (Lock
to
Lock-Linkage Disconnected)

Fluid Specifications

Fluid Capacity (Included in Pump Reservoir Fill)

Phosphorescent Dye Additive (For Leak Detection)

Sector Shaft End Play -Linkage Disconnected

Sector Shaft Mesh Load. Total Over Mechanical Center

Position.
Must beCDGreater Than Worm

Bearing Preload Torque, Shown Below

Worm Bearing Preload

Clearance Between Valve Spool
&
Retaining Ring

Pressure Variation Between Right
&
Left Turn (At 250
P.S.I.)
-

Check Efforts Each Side
of
Center

Clearance Between Inner Sector Seal and Housing
Ford Design

(XR-«0)
Saginaw

Design

Recirculating Ball Torsion Bar

17:1

4
17.5:1

41/8

M-2C33-F

1.6 Pints (Approx.)

M99B103-A(4 0z. per quart)

None

14 In Lb (Max)

(Exc. Lincoln)

17
In
Lb (Max.)

(Lincoln)

2-7 la
U)

.0035-.0005"

Preferable .002"

4
In
Lb Max.

Variation

.025"
.002"
Max.

14
In
Lb (Max)

4-7 In Lb®

_

—

-

©8-9 In Lb (XR-50 Exc. Lincoln) 11-12 In Lb
for
Uncoln,
4-8 In
Lb
for
Saginaw Gear.

® 3 In Lb in Excess of Valve Assy. Drag Total Worm Bearing Preload and Seal Drag
not to
Exceed
8 In
Lb.procarmanuals.com