carb FORD MUSTANG 1969 Volume One Chassis

02-02-09
Brake System

02-02-09

REMOVAL AND INSTALLATION

FRONT BRAKE DRUM

REMOVAL

1.
Raise the vehicle until the wheel

and tire clear the floor. Remove the

wheel cover or hub cap, and remove

the wheel and tire from the drum.

2.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

3.
Pull the drum off the wheel

spindle.

4.
If the drum will not come off,

pry the rubber cover from the brake

backing plate. Insert a narrow screw-

driver through the slot and disengage

the adjusting lever from the adjusting

screw. While holding the adjusting

lever away from the screw, back off

the adjusting screw with the brake ad-

justing tool (Fig. 13). Be very careful

not to burr, chip, or damage the

notches in the adjusting screw; other-

wise the self-adjusting mechanism will

not function properly.

INSTALLATION

1.
If the drum is being replaced, re-

move the protective coating from the

new drum with carburetor degreaser.

Then, use sandpaper to insure that no

residue remains. Wipe the drum with

a cloth soaked with denatured alcohol.

Install new bearings and grease seal.

Pack the wheel bearings, install the

inner bearing cone and roller assembly

RUBBER PLUG

REMOVED

'MOVE HANDLE UPWARD

TO RETRACT BRAKE SHOES
in the inner cup, and install the new

grease seal see Part 3-5, Section 4.

If the original drum is being in-

stalled, make sure that the grease in

the hub is clean and adequate.

2.
Adjust the brakes and install the

drum assembly as outlined under

Brake Shoe Adjustments in this sec-

tion.

3.
Install the outer wheel bearing,

washer and adjusting nut.

4.
Adjust the wheel bearing as out-

lined in Part 3-7, Section 2, then in-

stall the grease cap. Install the wheel

and hub cap.

REAR BRAKE DRUM

REMOVAL

1.
Raise the vehicle so that the tire

is clear of the floor.

2.
Remove the hub cap and wheel.

Remove the three Tinnerman nuts and

remove the brake drum. If the drum

will not come off, pry the rubber

cover from the backing plate. Insert a

narrow screwdriver through the hole

in the backing plate, and disengage

the adjusting lever from the adjusting

screw. While holding the adjusting

lever away from the adjusting screw,

back off the adjusting screw with the

brake adjusting tool (Fig. 13). Be very

careful not to burr, chip, or damage

the notches in the adjusting screw;

otherwise, the self-adjusting mecha-

nism will not function properly.

INSTALLATION

1.
Remove the protective coating

from a new drum with carburetor de-

greaser; then sand lightly and wipe

with a cloth soaked with denatured al-

cohol.

HI 590-A
H1390-A

FIG. 73—Backing Off Brake

Adjustment
FIG. 14—Retracting Spring

Removal
2.
Adjust the brakes as outlined

under Brake Shoe Adjustments in this

section. Place the drum over the brake

assembly and into position.

3.
Install the three Tinnerman nuts

and tighten securely. Install the wheel

on the axle shaft flange studs against

the drum, and tighten the attaching

nuts to specifications.

BRAKE SHOES AND

ADJUSTING SCREW-

DRUM BRAKES

REMOVAL

1.
With the wheel and drum re-

moved install a clamp over the ends of

the brake cylinder as shown in Fig.

14.

2.
Remove the secondary shoe to

anchor spring with the tool shown in

Fig. 14. With the same tool remove

the primary shoe to anchor spring and

unhook the cable eye from the anchor

pin.

3.
On Ford, Mercury, Meteor,

Thunderbird, Continental Mark III

and Lincoln Continental models, re-

move the shoe guide (anchor pin)

plate (Fig. 8).

4.
Remove the shoe hold-down

springs, shoes, adjusting screw, pivot

nut, socket and automatic adjustment

parts.

5.
On rear brakes, remove the

parking brake link and spring. Dis-

connect the parking brake cable from

the parking brake lever.

*>.
After removing the rear brake

secondary shoe, disassemble the park-

ing brake lever from the shoe by re-

moving the retaining clip and spring

washer (Fig. 8).

INSTALLATION

1.
Before installing the rear brake

shoes,
assemble the parking brake

lever to the secondary shoe and secure

with the spring washer and retaining

clip.

2.
Apply a light coating of high-

temperature grease at the points

where the brake shoes contact the

backing plate.

3.
Position the brake shoes on the

backing plate and secure the assembly

with the hold down springs. On the

rear brake, install the parking brake

link and spring, back off the parkingprocarmanuals.com

02-02-19
Brake System

02-02-19

that the tabs on the shoe flanges seat

fully against the caliper bridges (Fig.

25).

2.
Install the caliper splash shield

and secure the shield to the caliper

with two retaining bolts (Fig. 4).

3.
Pump the brake pedal several

times until a firm pedal is obtained

and the shoe and lining assemblies are

properly seated.

4.
Install the wheel and tire assem-

bly on the hub and rotor assembly.

5.
Check and refill the master cyl-

inder reservoir with specified brake

fluid as required.

6. Road test the car.

It should not be necessary to bleed

the system after a shoe and lining re-

placement.

FRONT WHEEL HUB AND

ROTOR ASSEMBLY-

DISC BRAKES

REMOVAL

1.
Remove the wheel and tire from

the hub (Figs. 23 and 24). Be careful

to avoid damage or interference with

the bleeder screw fitting. On Lincoln

Continental models be careful to avoid

damage to the caliper splash shield or

transfer tube.

2.
Remove the caliper assembly

from the spindle and the rotor. If the

caliper does not require servicing, it is

not necessary to disconnect the brake

hose or remove the caliper from the

vehicle. Position the caliper out of the

way, and support it with a wire to

avoid damaging the caliper or stretch-

ing the hose. Insert a clean cardboard

spacer between the linings to prevent

the piston from coming out of the cyl-

inder bore while the caliper is re-

moved.

Handle the rotor and caliper assem-

blies in such a way as to avoid defor-

mation of the rotor and nicking,

scratching or contamination of the

brake linings.

3.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

4.
Remove the hub and rotor as-

sembly from the spindle.

INSTALLATION

1.
If the rotor is being replaced, re-

move the protective coating from the

new rotor with carburetor degreaser.

Pack a new set of bearings with speci-
fied grease (M-1C75B), and install the

inner bearing cone and roller assembly

in the inner cup. Pack grease lightly

between the lips of a new grease seal

and install the seal (Figs. 23 and 24).

If the original rotor is being in-

stalled, make sure that the grease in

the hub is clean and adequate, that

the inner bearing and grease seal are

lubricated and in good condition, and

that the rotor braking surfaces are

clean.

2.
Install the hub and rotor assem-

bly on the spindle.

3.
Lubricate and install the outer

wheel bearing, washer and adjusting

nut.

4.
Adjust the wheel bearings to

specification, and then install the nut

lock, cotter pin, and grease cap. The

wheel bearing adjustment is especially

important with disc brakes.

5. Mount the caliper assembly on

the spindle following the Disc Brake

Caliper Assembly Installation proce-

dure in this section.

DISC BRAKE ROTOR

SPLASH SHIELD

REMOVAL

1.
Remove the caliper and the hub

and rotor assembly as outlined under
Removal in the foregoing procedure

(it is not necessary to disconnect hy-

draulic connections).

2.
Remove the three bolts that at-

tach the splash shield to the spindle,

and remove the shield (Figs. 23 and

24).

3.
Remove and discard the splash

shield to spindle gasket.

INSTALLATION

1.
Install a new splash shield to

spindle gasket.

2.
If the shield is bent, straighten it

out before installation. Position the

shield to the mounting bracket, install

the attaching bolts, nuts and torque

them to specification.

3.
Install the hub and rotor assem-

bly and the caliper as outlined under

Installation in the foregoing proce-

dure.

DUAL MASTER CYLINDER—

NON POWER BRAKES

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 26.

BUSHING

HAIRPIN

RETAINER

BUSHING

STOPLIGHT SWITCH

13480
HI 637-A

FIG. 26—Dual Master Cylinder Installation— Non Power Brakes

Ford,
Mercury, and Meteorprocarmanuals.com

07-01-05
General Transmission Service

07-01-05

linkage may cause crossleakage and

subsequent transmission failure. Refer

to Linkage Adjustments in Part 7-2,

7-3 or 7-4 for detailed manual linkage

adjustment procedures.

CONTROL PRESSURE

CHECK

When the vacuum diaphragm unit is

operating properly and the downshift

linkage is adjusted properly, all the

transmission shifts (automatic and

kickdown) should occur within the

road speed limits specified in Part 7-5.

If the shifts do not occur within

limits or the transmission slips during

shift point, the following procedure is

suggested to determine engine, trans-

mission, linkage, vacuum diaphragm

unit or valve body problems.

1.
Using the automatic transmis-

sion tester (Fig. 4), attach the tachom-

eter to the engine and the vacuum

gauge to the transmission vacuum line

at the vacuum unit (Fig. 5).

D 1823-A

. 4—Rotunda ARE-2905

Automatic Transmission Tester

T - FITTING
2.
Attach the pressure gauge to the

control pressure outlet at the trans-

mission (Figs. '., and 7).

3.
Firmly apply the parking brake

and start the engine.

On a vehicle equipped with a vacu-

um brake release, apply the service

brakes. The parking brake can not be

used because the brake automatically

VACUUM DIAPHRAGM UNIT

CLIP

I

| CONTROL PRESSURE TAKE-OFF HOLE

D2041-A

FIG. 6—Typical Vacuum

Diaphragm and Control Pressure

Connecting Point
releases when the transmission selec-

tor lever is moved to a drive position.

4.
Adjust the engine idle speed lo

the specified rpm. If the engine idle

speed cannot be brought within limits

by adjustment at the carburetor idle

adjustment screw, check the throttle

and downshift linkage for a binding

condition. If the linkage is satisfacto-

ry, check for vacuum leaks in the

transmission diaphragm unit (Fig. 8

or 9) and its connecting tubes and

hoses.
Check all other vacuum oper-

ated units (such as the power brake)

for vacuum leaks.

VACUUM UNIT CHECK

NON-ALTITIDE

COMPENSATING TYPE

To check the vacuum unit for dia-

phragm leakage, remove the unit from

the transmission. Use a distributor

D1840-A

FIG. 8—Testing Transmission

Vacuum Unit for Leakage

VACUUM DIAPHRAGM

D 1643 -C

FIG. 5—Typical Vacuum Test

Line Connections
FIG.
7—Vacuum
Diaphragm and Control and TV Pressure Connecting

Points—C6 Transmissionprocarmanuals.com