key FORD MUSTANG 1969 Volume One Chassis

03-01-09
Suspension — Steering, Wheels And Tires — General Service

03-01-09

the reading exceeds specifications

(Part 3-13), replace the upper ball

joint.

LOWER BALL JOINT

INSPECTION

Ford,
Mercury, Meteor,

Thunderbird, Lincoln Continental

and Continental Mark III

1.
Raise the vehicle and place

jacks under the lower arms as shown

in Fig. 12. This will unload the lower

ball joints.

2.
Adjust the wheel bearings as des-

cribed in Part 3-12.

3.
Attach a dial indicator to the

lower arm and position the indicator

so that the plunger rests against the

inner side of the wheel rim adjacent to

the lower ball joint.

4.
Grasp the tire at the top and

bottom and slowly move the tire in

and out (Fig. 19). Note the reading

(radial play) on the dial indicator. If

the reading exceeds specifications

(Part 3-13), replace the lower ball

joint.

Cougar, Fairlane, Falcon,

Montego, Mustang

1.
Raise the vehicle on a frame

contact hoist or by floor jacks placed

beneath the underbody until the wheel

falls to the full down position.

2.
Ask an assistant to grasp the

lower edge of the tire and move the

wheel in and out.

3.
As the wheel is being moved in

and out, observe the lower end of the

spindle and the lower arm.

4.
Any movement between the

lower end of the spindle and the lower

arm indicates ball joint wear and loss

of preload. If any such movement is

observed, replace the lower arm.

During the foregoing check, the

upper ball joint will be unloaded and

may move. Disregard all such move-

ment of the upper ball joint. Also, do

not mistake loose wheel bearings for a

worn ball joint.

POWER STEERING GEAR

CLEANING

Disassembly and assembly of the

steering gear and. the sub-assemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost
importance. The bench, tools, and

parts must be kept clean at all times.

Thoroughly clean the exterior of the

unit with a suitable solvent and, when

necessary drain as much of the hy-

draulic fluid as possible. Handle all

parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use.

Do not clean, wash or soak seals in

cleaning solvent.

INSPECTION

1.
Check the sector shaft contact

surface in the cover for wear. If worn,

replace the cover.

2.
Inspect the input shaft bearing

for cracked races and the balls for

looseness, wear, pitting, end play or

other damage. Check the fit of the

bearing on the input shaft. Replace

the bearing, if required.

3.
Inspect the valve housing for

wear, scoring or burrs.

4.
Inspect the tube seats in the

pressure and return ports in the valve

body for nicks, etc. If necessary, re-

move and replace.

5.
Check the sector shaft contact

surface in the housing for wear. If

worn, replace the bushing or the hous-

ing.

6. Check all fluid passages for ob-

struction or leakage.

7.
Inspect the steering gear housing

for cracks, stripped threads, and mat-

ing surfaces for burrs. Inspect the pis-

ton bore of the housing for scoring or

wear. If necessary, replace the hous-

ing.

8. Check the input shaft bearing

after installation to be sure that it ro-

tates freely.

9. If the valve spool is not free in

the valve housing, check for burrs at

the outward edges of the working

lands in the housing and remove with

a hard stone. Check the valve spool

for burrs and if burrs are found, stone

the valve in a radial direction only.

Check for freedom of the valve again.

10.
Check the piston rack teeth and

sector shaft teeth for nicks and burrs.

FLUSHING THE POWER

STEERING SYSTEM—ALL EXCEPT

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

Should it be necessary to replace an

inoperative power steering pump, the

need for flushing the steering system

is required when installing the new

pump.
1.
Remove the power steering pump

and remove the pulley as outlined in

Part 3-10.

2.
Install the pulley on a new

pump. Install the pump and connect

only the pressure hose to the pump

(Part 3-10).

3.
Place the fluid return line in a

suitable container and plug the reser-

voir return pipe.

4.
Fill the reservoir with lubricant

(C1AZ-19582-A).

5.
Disconnect the coil wire to pre-

vent the engine from starting and raise

the front wheels off the ground.

6. While approximately two quarts

of steering gear fluid are being poured

into the reservoir, turn the engine over

using the ignition key, at the same

time cycle the steering wheel from

stop to stop.

7.
As soon as all of the lubricant

has been poured in, turn off the igni-

tion key, and attach the coil wire.

8. Remove the plug from the reser-

voir return pipe, and attach the return

hose to the reservoir.

9. Check the reservoir fluid level; if

low, add fluid to the proper level. Do

not overfill.

10.
Lower the vehicle.

11.
Start the engine and cycle the

steering from stop to stop to expel

any trapped air from the system.

POWER STEERING PUMP—ALL

EXCEPT LINCOLN

CONTINENTAL AND

CONTINENTAL MARK III

CLEANING

Wash all parts (except seals) in a

Naptha or Chlorinated-type solvent

and dry with compressed air.

Punch or Rod

RELIEF VALVE PLUNGER

G1607-A

FIG.
20—Cleaning Pump Relief Valveprocarmanuals.com

03-01-10
Suspension — Steering, Wheels And Tires — General Service

03-01-10

The following procedure should be

followed when cleaning the relief valve

which is a part of the pump valve as-

sembly.

1.
Using a punch or rod of suitable

diameter, apply an even pressure in a

straight line to the tip of the relief

valve pin (Fig. 20). Depress the valve

two or three times to exhaust the oil

which is trapped in the assembly. Do

not hammer on the valve pin or hous-

ing.

2.
Submerge the assembly in a con-

tainer of clean solvent. Again applying

an even pressure to the tip of the relief

valve pin, (a sudden strong force could

push the pin through the relief valve

spool) move the valve in and out sev-

eral times, thereby thoroughly flushing

the assembly. Pressure created within

the valve bore when the valve is moved

inward should force the cleaning fluid

out through the sensing orifice. If this

does not occur, the sensing orifice

should be cleaned with a piece of wire.

The valve must move freely and even-

ly. If the pin is bent or damaged, or if

the valve binds, the pump valve must

be replaced.

INSPECTION

The following describes the compo-

nents of the power steering pump

which must be replaced regardless of

condition and how to determine when

other components should be replaced.

The outlet fitting hex nut may be

reused if the corners of the hex are

not rounded. The housing bolts may

be reused if the threads are not dam-

aged.

All gaskets and seals must be re-

placed with new components except

the rotor shaft seal which should be

reused unless it was leaking.

The reservoir assembly may be

reused if the reservoir seal and gasket

areas are not damaged (dents, scratch-

es,
etc.). The soldered joints of the re-

turn and fill tubes must not be loose

or bent. Be sure to check for a broken

baffle.

The housing or housing assembly

may be reused if there is no damage

(scratches, etc.) at reservoir gasket,

outlet fitting or cover seal areas.

If the outlet fitting is damaged, the

pump housing must be replaced. The

pressure plate springs may be reused

providing they are not bent, broken or

have not taken a set.

Do not reuse the retainer end plate

if it is burred or damaged. The upper

pressure plate may be reused if there

is no scoring on the wear surface. It is

acceptable to polish the phosphate

coating.
The rotor and cam assembly can be

reused if there is no wear other than

the removal of the phosphate coating

on the cam contour. Do not disas-

semble the rotor and cam assembly.

Push the rotor part way out the cam

insert taking care not to let the slip-

pers and springs fall out. Check the

cam ID for scoring and burning.

Check the rotor faces and OD for

scoring and chipping. Do not attempt

to repair or refinish the lower and

upper pressure plates, cam or rotor

assembly. When wear or burning is

encountered, replace, them with new

components.

Install a new rotor and cam assem-

bly if the slippers are worn. Replace

the springs if they are bent or broken.

Polishing the phosphate coating of the

slipper sealing surface is permissable.

The rotor shaft can be reused if the

front and rear thrust faces, the bush-

ing diameter and the shaft seal diame-

ter are not excessively worn or scored.

The housing plate and bushing as-

sembly may be reused if all of the

threaded holes are not damaged

beyond repair and the bushing diame-

ter is not scored or worn .0005 inch

over the maximum dimension of .6897

inch. Threaded holes can be repaired

by drilling out the damaged threads

and installing a helicoil insert. If the

bushing is scored or excessively worn,

a new plate and bushing assembly

must be installed.

With Tool T69P-3D608-A (using a

dial indicator) check the squareness of

the fixed dowel pin in the plate (Fig.

21).
The pin must be square with the

adjacent surface within .001 inch per

inch through a 180 degree arch.

A bent or broken dowel pin can be

replaced as follows:
1.
Hold the plate assembly in a

horizontal position and grip at least

an inch of the dowel pin in a vise. Tap

the plate with a plastic or a rubber

hammer to pull the pin from the

plate.

2.
Insert the support guide (Tool

T69P-3D608-B) over a dowel pin (Fig.

22) and press the pin into the plate to

a height of 1.68 inch (See Fig. 23).

The support guide tool will serve as a

stop guide. Be careful not to bend the

new dowel pin during installation.

3.
Again use Tool T69P-3D608-A

(with a dial indicaator) to check the

dowel pin squareness as outlined

above.

POWER STEERING PUMP

INSPECTION—LINCOLN

CONTINENTAL AND

CONTINENTAL MARK III

1.
Wash all parts in clean solvent

and dry them with clean cloths or

compressed air.

2.
Inspect the rotor shaft for wear,

scoring, nicks, or burrs. Replace the

shaft if it is damaged or if the inner

keyway is damaged.

Tool
T69P-3D608-B

G1609-A

FIG. 22—Dowel Pin Insertion

Tool
T69P-3D608-A

G1608-A

FIG. 21—Dowel Pin Squareness

Check
FIG. 23 — Replacing Dowel Pinprocarmanuals.com

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-05-02
Steering Columns
And
Linkage

03-05-02

which also will shear away during
im-

pact.

TILT STEERING COLUMNS

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column
must
be
installed.

The tilt column features nine driv-

ing positions (four
up and
four down

from
a
center position).
The
.column

also features
a
turn signal switch with

a lane-changer position turn indicating

position
and
emergency warning flash-

er control.

TILT-AWAY STEERING COLUMNS

The tilt-away steering column
fea-

tures nine driving positions (four
up

and four down from
a
center position)

and
a
tilt-away position that
is
auto-

matically accomplished
on
Mustang

and Cougar models when
the
ignition

key
is
turned
to the
OFF
position
and

the left door
is
opened.
On
Thunder-

bird models,
the
tilt-away occurs when
the shift lever
is
placed
in
PARK
and

the driverns door
is
opened.

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column

must
be
installed along with mounting

brackets which will also shear away

during impact.

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

STEERING WHEEL SPOKE

POSITION ADJUSTMENT

When
the
steering gear
is on the

high point,
the
front wheels should
be

in
the
straight-ahead position
and the

steering wheel spokes should
be in

their normal position with
the
Pitman

arm pointing directly forward.
If the

spokes
are not in
their normal posi-

tion, they
can be
adjusted without
dis-

turbing
the
toe-in adjustment (Part

3-1).

STEERING WHEEL

REPLACEMENT

1.
Disconnect
the
negative cable

from
the
battery.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

crash
pad
attaching screws. Lift
the

crash
pad
from
the
wheel.
(On
Conti-

nental Mark
III
models,
pry out the

crash
pad
insert
and
remove
the two

screws that secure
the
crash
pad. Re-

move
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
nut,

and then remove
the
steering wheel

with tool T67L-3600-A
(Fig. 1). Do

not
use a
knock-off type steering

wheel puller
or
strike
the end of the

steering shaft with
a
hammer. Striking

the puller
or
shaft will damage
the

bearing
or the
collapsible column.

4.
Transfer
all
serviceable parts
to

the
new
steering wheel.

5.
Position
the
steering wheel
on

the shaft
so
that
the
alignment mark
on
the hub of the
wheel
is
adjacent
to

the
one on the
shaft. Install
a new

locknut
and
torque
it to
specifications.

6. Install
the
horn ring
(if so

equipped)
and
crash
pad.

STEERING COLUMN UPPER

BEARING REPLACEMENT

STATIONARY COLUMNS

Removal

1. Disconnect
the
horn wire
and the

turn indicator wires
at the
connector.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

two crash
pad
attaching screws. Lift

the crash
pad
from
the
wheel.
(On

Continental Mark
III
models,
pry out

the crash
pad
insert
and
remove
the

two screws that secure
the
crash
pad.

Remove
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

7oo/-T67L-3600-A
removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
at-

taching
nut.
Remove
the
steering

wheel using tool T67L-3600-A
(Fig.

1).
Do not use a
knock-off type steer-

ing wheel puller
or
strike
the end of

the steering shaft with
a
hammer.

Striking
the
puller
or
shaft will
dam-

age
the
bearing
or the
collapsible
col-

umn.

4.
Remove
the
turn indicator lever.

5.
Remove
the
turn signal switch

attaching screws. Lift
the
switch over

the
end of the
steering shaft
and
place

it
to one
side.

6. Remove
the
snap ring from
the

top
of the
steering shaft.

7.
Loosen
the two
flange-to-steering

column tube attaching bolts
to
disen-

gage them from
the
tube.

8. Raise
the
flange upward while

BEARING
AND

INSULATOR

Spacer

G 1502 -B

FIG.
1—Removing
Steering Wheel
G 1497-A

FIG. 2—Installing Upper Bearingprocarmanuals.com

03-11-01
Eaton Power Steering Pump

03-11-01

PART 3-11 Eaton Power Steering Pump

COMPONENT INDEX
MODEL APPLICATION

3
§>
"o

4

POWER STEERING PUMP

Cleaning and Inspection (See Part 03-01)

Description

N/A
N/A
N/A
N/A
N/A
N/A

N/A
N/A
11-01

N/A
11-01

Disassembly and Overhaul

N/A
N/A

N/A
N/A

N/A
N/A

N/A
N/A
11-03

N/A
11-03

Removal and Installation

N/A
N/A
N/A
N/A

N/A
N/A
N/A
N/A
11-01
N/A

11-01

POWER STEERING PUMP RESERVOIR

Removal and Installation

N/A
N/A
N/A

N/A
N/A
N/A

N/A

N/A

11-01
N/A

11-01

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

l
DESCRIPTION

The roller-type hydraulic pump,

driven by the crankshaft, draws auto-

matic transmission fluid down the res-

ervoir and provides fluid pressure for

the system. Steering gear lubrication
is also provided by the same fluid

from the reservoir. Within the pump

itself is a flow-control and pressure-

relief valve which governs the pres-
sures within the steering system ac-

cording to the varying conditions of

operation. After fluid has passed from

the gear, it returns to the reservoir.

REMOVAL AND INSTALLATION

POWER STEERING PUMP

REMOVAL

1.
Open the hood, and install fend-

er covers.

2.
If the vehicle is equipped with air

conditioning, loosen the compressor

adjusting and support bracket bolts

and remove the drive belt.

3.
Loosen the generator adjusting

and support bracket bolts, and remove

the drive belts.

4.
Remove the fan, pulley, and spa-

cer.

5.
Raise the vehicle.

6. Remove the crankshaft damper

bolt and washer. Remove the damper

with Tool 6306-AG. Remove the drive

key.

7.
Disconnect the pump inlet line at

the pump, and plug the end of the line

to prevent the loss of fluid. Disconnect

the pump pressure line at the pump.
8. Remove the pump-to-engine

front cover cap screws, and remove

the pump. Remove the seal from the

front cover.

INSTALLATION

1.
Install a new seal on the engine

front cover.

2.
Align the slot in the pump rotor

shaft with the drive key in the crank-

shaft, and slide the pump onto the

shaft. Install the pump-to-engine front

cover cap screws. Torque the cap

screws to specification.

3.
Connect the pump inlet line and

the pressure line.

4.
Install the damper drive key,

damper, washer and bolt. Torque the

bolt to specification.

5.
Install the fan, pulley, and spa-

cer. Install the generator drive belts.

Adjust the belt tension, and tighten

the adjusting and support bracket

bolts.
6. If the vehicle is equipped with air

conditioning, install the compressor

drive belt. Adjust the belt tension, and

tighten the adjusting and support

bracket bolts.

7.
Run the engine at idle speed,

and check the fluid level in the reser-

voir. If required, add the specified au-

tomatic transmission fluid. Turn on

the windshield wipers. Rotate the

steering wheel from stop to stop sever-

al times to bleed the air from the sys-

tem. Recheck the fluid level.

POWER STEERING PUMP

RESERVOIR

WITHOUT AIR

CONDITIONING

Removal

1.
Remove the reservoir cover andprocarmanuals.com

03-11-03

Eaton Power Steering Pump

03-11-03

POWER STEERING PUMP

DISASSEMBLY

A clean working area should be

used when overhauling the power

steering pump. Foreign matter picked

up on working parts may cause dam-

age or failure of the unit. Clean con-

tainers should be used for parts.

1.
Drain the fluid from the pump.

Remove the pump cover-to-housing

cap screws (Fig. 1). Place the pump

on the bench, cover side down. Lift

the housing from the cover.

2.
Remove the large and the small

O-rings from the pump cover. Remove

the O-ring from the pressure plate

hub.

3.
Remove the pressure plate-

to-cover screws, and remove the plate.

Lift the cam ring off the dowel pins.

4.
Remove the rollers. Lift the

rotor off the shaft, and remove the

drive key from the shaft. Remove the

dowel pins from the cover.

5.
Remove the rotor shaft from the

cover. Do not remove the snap ring

from the shaft unless it, or the shaft,

is damaged.

6. Pry the rotor shaft seals out of

the cover and the housing.

7. Do not disturb the control valve

unless diagnosis indicated a control

valve problem or foreign matter in the

valve. To remove the valve, drive the

roll pin out of the housing. Remove

the plug and O-ring, control valve,

and the spring. If the plug or valve is

stuck, tap the end of the housing on a

piece of wood or tap it with a soft-

faced hammer. Remove the O-ring

from the plug.

ASSEMBLY

Apply automatic transmission fluid

to all parts as they are assembled. Al-

ways use new seals and O-rings.

1.
Install the control valve spring in

the housing. Install the valve with the

small sensing hole in the end of the

valve toward the spring. Install a new

O-ring on the plug. The plug O-ring is

1/8 inch smaller in diameter than the

bypass O-ring. Make sure the proper

O-ring is used. Install the plug and a

new roll pin (Fig. 1).

2.
The rotor shaft oil seals are in-

stalled in the cover and the housing

with Tool 3583-J, which consists of a

driver and an adapter. The procedure

is as follows:

a. Support the cover on wood

blocks (Fig. 2) to provide tool clear-

ance.
Use clean blocks that will not

nick or damage the inner face of the

cover.
b.
Start the seal (metal shell up-

ward) square!y into the bore with fin-

ger pressure. Place the adapter on the

driver with the square corner of the

FIG. 2—Preparation for Installing

Rotor Shaft Seals

adapter toward the seal (Fig. 2). Drive

the seal into the cover, as shown in

Fig. 3, until it bottoms.

Driving the seal beyond this point

can damage it. Install the seal in the

pump housing in the same manner.

3.
Install the rotor shaft in the

FIG. 3—Installing Rotor

Shaft Seals
cover as shown in Fig. 4 to prevent

damage to the seal.

4.
Install the dowel pins in the

cover. Place the rotor drive key in the

shaft. Install the rotor on the shaft

with the drive key groove aligned with

the key and the counterbored side of

the rotor toward the cover so that it

goes over the snap ring.

5.
Place the cam ring on the dowel

pins with the chamfered edge upward

(Fig. 5). Place the rollers in the rotor.

6. Place the pressure plate on the

dowel pins. Install and tighten the

screws to 20 in-lbs torque. Install the

O-ring on the pressure plate hub. In-

stall O-rings in the groove at the fluid

bypass hole and around the cam ring

(Fig. 6).

7.
Place the tool shown in Fig. 6 in

the rotor shaft to prevent damage to

the oil seal, then install the housing on

the cover. Install and torque the cap

screws to 15-20 ft-lbs.

FIG. 5—Cam Ring Installation

FIG. 4—Installing Rotor Shaft

in Cover

FIG. 6—O-Ring Installationprocarmanuals.com

04-05-06

Specifications

04-05-06

THUNDERBIRD, CONTINENTAL MARK
III

Ford Tool No.

T50T-100-A

T50T-100-A&

TOOL-1175-AB

T00L-1225-DA

TOOL-4005

TOOL-4020-B

T57L-4067-A

TOOL-4201

TOOL-4201-C

TOOL-4205-B

TOOL-4205-C

T00L-4221-C

T00L-4222-H

T00L-4235-C

T00L-4245-B
Former No.

T50T-100-C

1175-AE

1225-DA

4005

4020-B

_

4201

4201-C

4205-B

4205-C

4221-C

4222-H

4235-C

4245-B
Description

Slide Hammer

Seal Remover

Rear Wheel Bearing Remover

Engine Repair Stand Axle Adapter-

Keyed Shaft

Pinion Depth Gauge-Complete With

Depth Micrometer and Gauge Block

Differential Bearing Adjuster Wrench

Pinion Shaft Drive
Nut

Differential Backlash
&
Runout

Gauge With Univ. Bracket, Dial

Indicator and Bracket

Differential Assembly Bench Holder

Axle Housing Dummy Bearings (1
pr.)

Differential Side Bearing Remover

Differential Bearing Cone Replacer

Axle Shaft
&
Bearing Remover

Wheel Bearing Seal Replacer
Ford Tool No.
Former No. Description

TOOL-4616
4616
Drive Pinion Bearing Cup Replacer

(Front)

T00L-4621-A 4621-A Drive Pinion Bearing and Rear Wheel

Bearing Replacer

T00L-4621-BA 4621-BA Rear Pinion Bearing Remover

TOOL-4628 4628 Pinion Rear Bearing Cup Replacer

T00L-4628-B 4628-B Pinion Bearing Front Cup Remover

T00L-4628-D 4628-D Pinion Rear Bearing Cup Remover

T64N-4676-A 4676 Pinion Shaft Oil Seal Replacer

T68P-4851-A
-
Universal Joint Flange Holder

T64N-4858-A 4858-B Companion Flange
&
Pinion Bearing

Replacer

T00L-4858-G 4858-G Pinion Flange Nut Adjusting Wrench

(Use With T64N-4858-A)

TOOL-4859 4859 Companion Flange Dust
Shield
Replacer

T00L-6565-AB
-
Dial Indicator Adapter

TOOL-6565
-
Dial Indicator

T00L-7657-J 7657-J Extension Housing Bushing
&

Seal Replacer

LINCOLN CONTINENTAL

Ford Tool
No.

T00L-4245-B

TOOL-4616

T00L-4621-A

T00L-4621-BA

TOOL-4628

T00L-4628-B

T64N-4628-B

T00L-4628-D

T64N-4676-A

T00L-4851-K

T64N-4858-A

T00L-4858-G

TOOL-4859

T00L-6565-AB

TOOL 6565

T00L-7657-J
Former
No.

4245-B

4616

4621-A

4621-BA

4628

4628-B

4628-D

4676

T57L-4851-A

4858-B

4858-G

4859

7657-J
Description

Wheel Bearing Seal Replacer

Drive Pinion bearing
Cup

Replacer (Front)

Drive Pinion Bearing
and
Rear

Wheel Bearing Replacer

Rear Pinion Bearing Remover

Pinion Rear Bearing
Cup
Replacer

Pinion Bearing Front
Cup
Remover

Pinion Rear Bearing Cup Remover

Pinion Shaft
Oil
Seal Replacer

Universal Joint Flange Holder

Companion Flange
&
Pinion Bearing

Replacer

Pinion Flange
Nut
Adjusting Wrench

(Use With T64N-4858-A)

Companion Flange Dust Shield

Replacer

Dial Indicator Adapter

Dial Indicator

Extension Housing Bushing
&

Seal Replacer
Ford Tool
No.
Former
No.

T50T-100-A

T50T-100-A&

TOOL-1175-AB

TOOL-1225-DA

TOOL-4000-C

TOOL-4005

TOOL-4020-B

TOOL-4201

TOOL-4201-C

TOOL-4204-A

TOOL-4205-B

TOOL-4205-C

T00L-4209-C

T00L-4221-C

T00L-4222-H

T00L-4235-C
Description

T50T-100-C Slide Hammer

1175-AE

1225-DA

4000-C

4005

4020-B

4201

4201-C

4205-B

4205-C

4209-C

4221-C

4222-H

4235-C
Seal Remover

Rear Wheel Bearing Remover

Differential Housing Spreader

Engine Repair Stand Axle Adapter-

Keyed Shaft

Pinion Depth Gauge-Complete With

Depth Micrometer
and
Gauge

Block

Pinion Shaft Drive
Nut

Differential Backlash
&
Runout

Gauge With Univ. Bracket, Dial

Indicator
and
Bracket

Limited Slip Differential Check

Differential Assembly Bench Holder

Axle Housing Dummy Bearings

(1
pi")

Pinion Tension Scale With

4209-C12 Socket

Differential Side Bearing Remover

Differential Bearing Cone Replacer

Axle Shaft
&
Bearing Removerprocarmanuals.com

07-01-12
General Transmission Service

07-01-12

the transmission,
any
metal particles

or clutch plate
or
band material that

may have been carried into
the
cooler

should
be
removed from
the
system
by

flushing
the
cooler
and
lines before

the transmission
is put
back into serv-

ice.
In no
case should
an
automatic

transmission having
a
clutch
or
band

failure
or
other internal trouble result-

ing
in
fluid contamination,
be put

back into service without first flushing

the transmission
oil
cooler.

To flush
the oil
cooler, follow
the

instruct!
on >
provided with
the
Rotun-

da Automatic Transmission Torque

Converter
and
Cooler Cleaner
LRE-

60081.

INSPECTION

TURBINE
AND
STATOR
END

PLAY CHECK

A special tool
(Fig. 19)
must
be

used
to
check
the
condition
of the

converter. This special tool
is
used
to

check
the
turbine
and
stator
end
play

and
the
operation
of the
one-way
sta-

tor clutch.

CRUISE-O-MATIC

Too/-T58L-7902-A

C-4 AND C-6 TRANSMISSION

Tool-T59P.7902.Bor 7937-B

ON C-4 AND C-6 TRANSMISSION

Tool-T64L-7902-A
D
1499-E

FIG. 19—Converter Checking Tool

1.
Insert
the
tool (Fig.
19)
into
the

converter pump drive
hub
until
it
bot-

toms.

2.
Install
the
guide over
the con-

verter pump drive
hub.
3.
Expand
the
split fiber bushing
in

the turbine spline
by
tightening
the

adjusting
nut.
Tighten
the
adjusting

nut until
the
tool
is
securely locked

into
the
spline.

4.
Attach
a
dial indicator
to the

tool (Fig.
20 or
21). Position
the
indi-

cator button
on a
converter pump

drive
hub, and set the
dial face
at 0

(zero).

5.
Lift
the
tool upward
as far as it

will
go and
note
the
indicator reading.

The indicator reading
is the
total
end

play which
the
turbine
and
stator

share.
If the
total
end
play exceeds

the limits specified
in
Part 7-5, replace

the converter unit.

6. Loosen
the
adjusting
nut to
free

the split bushing,
and
then remove
the

tool from
the
converter.

STATOR ONE-WAY CLUTCH

CHECK

1.
Install
the
stator outer race hold-

ing tool
in one of the
four holes
pro-

vided
in the
stator (Fig.
20 or 21).

2.
Insert
the
tool
in the
converter

pump drive hub.
As the
tool enters
the

converter,
the
pins will engage
the sta-

tor clutch inner race spline.

3.
Place
a
torque wrench
on the

tool (Fig.
20 or
21).
The
tool (and
sta-

tor inner race) should turn freely

clockwise (from
the
pump drive
hub

inside
the
converter).
It
should lock
up

and hold
a 10
ft-lb pull when
the

wrench
is
turned counterclockwise.

Try
the
clutch
for
lockup
and
hold
in

at least five different locations around

the converter.
On
the
C4
or C6
Auto-

matics,
the
metal ring holding
the

locking tool will have
to be
held
by

hand during this check.

4.
If the
clutch fails
to
lock
up and

hold
a 10
ft-lb torque, replace
the

converter unit.

STATOR
TO
IMPELLER

INTERFERENCE CHECK

1.
Position
the
front pump assem-

bly
on a
bench with
the
spline
end of

the stator shaft pointing
up
(Fig.
22).

2.
Mount
a
converter
on the
pump

so that
the
splines
on the
one-way

clutch inner race engage
the
mating

splines
of the
stator support,
and the

converter
hub
engages
the
pump drive

gear.

3.
While holding
the
pump station-

ary, try
to
rotate the converter counter-

clockwise.
The
converter should
ro-

tate freely without
any
signs
of
inter-

ference
or
scraping within
the
convert-

er assembly.
4.
If
there
is an
indication
of
scrap-

ing,
the
trailing edges
of the
stator

blades
may be
interfering with
the

leading edges
of the
impeller blades.

In such cases, replace
the
converter.

STATOR
TO
TURBINE

INTERFERENCE CHECK

1.
Position
the
converter
on the

bench front side down.

2.
Install
a
front pump assembly
to

engage
the
mating splines
of
the
stator

support
and
stator,
and
pump drive

gear lugs.

3.
Install
the
input shaft, engaging

the splines with
the
turbine
hub (Fig.

23).

4.
While holding
the
pump station-

ary, attempt
to
rotate
the
turbine with

the input shaft.
The
turbine should
ro-

tate freely
in
both directions without

any signs
of
interference
or
scraping

noise.

5.
If
interference exists,
the
stator

front thrust washer
may be
worn,
al-

lowing
the
stator
to hit the
turbine.
In

such cases,
the
converter must
be re-

placed.

The converter crankshaft pilot

should
be
checked
for
nicks
or dam-

aged surfaces that could cause inter-

ference when installing
the
converter

into
the
crankshaft. Check
the con-

verter front pump drive
hub for
nicks

or sharp edges that would damage
the

pump seal.

OUTPUT SHAFT
AND

PRIMARY
SUN
GEAR SHAFT

(FMX TRANSMISSION)

1.
Inspect
the
thrust surfaces
and

journals
for
scores. Inspect
the
inter-

nal gear
for
broken
or
worn teeth.

2.
Inspect
the
aluminum sleeve
for

scores
or
leakage. Inspect
the
ring

grooves
for
burrs.

3.
Inspect
the
keyway
and
drive

ball pocket
for
wear,
and
inspect
the

splines
for
burrs, twist
or
wear.

4.
Inspect
the
output shaft sleeve

for alignment with
the
governor drive

ball (Fig.
24).

5.
Inspect
the
external parking gear

teeth
for
damage
and the
speedometer

drive gear teeth
for
burrs.

6.
If
either
the
output shaft
or
ring

gear
has
been replaced, place
the as-

sembled unit with
the
gear face down

on
the
bench, push
the
shaft down-

ward,
and
check
the
clearance
be-

tween
the top of the
snap ring
and its

groove
(Fig. 25).
If
this clearance
ex-

ceeds 0.002 inch, replace
the
snap ring

with
a
thicker ring
to
reduce
the
clear-

ance
to
less than 0.002 inch. Selectiveprocarmanuals.com

07-02-06
C4 Automatic Transmission

07-02-06

PLUG-7256
•HANDLE-7217

BUTTON-7C439

DIAL HOUSING

ASSEMBLY-7E034

POINTER BACK-UP

SHIELD

ENGAGE FLATS OF STUD IN SLOT OF

ROD BEFORE APPLYING TORQUE

D2022-A

FIG. 8—Manual Linkage—Console Shift—Mustang

ACTUATOR LEVER ATTACHING BOLT

D1812-A

FIG. 9—Neutral Start Switch Adjustments—Console Shift—Ford-Meteor

9. Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.
10.
Place the console top panel on

the console and install the retaining

screws.

11.
Position the selector lever de-

tent control and handle on the selector
lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
With the manual linkage proper-

ly adjusted, check the starter en-

gagement circuit in all positions. The

circuit must be open in all drive posi-

tions and closed only in park and neu-

tral.

Gauge Pin

(No.43 Drill)

NEUTRAL START

SWITCH

Dl759-A

70—Neutral Start Switch

Adjustments—Console Shift—

Fairlane-Montegoprocarmanuals.com

07-02-07
C4 Automatic Transmission

07-02-07

2.
Remove the selector lever handle

from the lever.

3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 10).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG

1.
With the manual lever properly

NEUTRAL
START

SWITCH

(D1439-A

FIG. 11—Neutral Start Switch

Adjustments—Console Shift—

Mustang
adjusted, loosen the two switch attach-

ing bolts (Fig. 11).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 11).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE SHIFT

On vehicles equipped with a column

mounted neutral start switch, refer to

Part 7-1, Section 2, for the replace-

ment procedures.

FORD-METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 9).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle

MUSTANG

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 11).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 11).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.procarmanuals.com