oil FORD MUSTANG 1969 Volume One Chassis

02-01-08
Brakes

02-01-08

BEARING CUP

DIMENSION "B"

0.755 MINIMUM

DIMENSION "A'

0.395 MINIMUM

H1532-B

FIG. 12—Disc Brake Rotor Service

Limits—Lincoln Continental

per splash shield or the bleeder screw

fitting.

4.
Front wheel bearing end play is

critical and must be within specifica-

tions.

5.
Be sure the vehicle is centered on

the hoist before servicing any front

end components, to avoid bending or

damaging the rotor splash shield on

full right or left wheel turns.

6. The proportioning valve should

not be disassembled or adjustments

attempted on it.

7.
Riding of the brake pedal (com-

mon on left foot applications) should

be avoided during vehicle operation.

8. The wheel and tire must be re-

moved ' separately from the brake

rotor, unlike drum brakes where the
wheel, tire and drum are removed as a

unit.

9. On floating caliper type disc

brakes whenever the caliper is re-

moved the caliper locating pins should

be inspected for wear or damage.

10.
On floating caliper type disc

brakes, the caliper assembly must be

removed from the spindle prior to re-

moval of the shoe and lining assem-

blies.

11.
On floating caliper type disc

brakes the calipers must not be inter-

changed from one side to the other.

When the caliper is installed on its

proper anchor plate and spindle, the

bleeder screw will point to the rear of

the vehicle (Fig. 22). If a caliper is in-

stalled on the wrong side of the vehi-

cle,
it is not possible to bleed the sys-

tem properly.

12.
Do not attempt to clean or re-

store oil or grease soaked brake lin-

ings.
When contaminated linings are

found, brake linings must be replaced

in complete axle sets.

DRUM BRAKES

1.
Remove the wheel from the

drum, and remove the drum as out-

lined in Part 2-2, Section 2.

2.
Brush all dust from the backing

plates and interior of the brake

drums.

3.
Inspect the brake shoes for ex-

cessive lining wear or shoe damage. If

the lining is worn within 1/32 inch of

the rivet heads or if the shoes are

damaged, they must be replaced. Re-

place any lining that had been con-

taminated with oil, grease or brake
fluid. Replace lining in axle sets. Prior

to replacement of lining, the drum di-

ameter should be checked to deter-

mine if oversize linings must be in-

stalled.

4.
Check the condition of brake

shoes,
retracting springs, hold-down

springs, and drum for signs of over-

heating. If the shoes have a slight blue

coloring, indicating overheating, re-

placement of the retracting and hold-.

down springs is strongly recommended.

Overheated springs lose their pull and

could cause the new lining i:o wear

prematurely, if they are not replaced.

5. If the vehicle has 30,000 or more

miles of operation on the brake linings

or signs of overheating are present

when relining brakes, the wheel cylin-

ders should be disassembled and in-

spected for wear and entrance of dirt

into the cylinder. The cylinder cups

should be replaced, thus avoiding fu-

ture problems.

6. Inspect all other brake parts and

replace any that are worn or dam-

aged.

7.
Inspect the brake drum and, if

necessary, refinish. Refer to Part 2-2,

Section 4 for refinishing.

BRAKE BOOSTER

Check the booster operation as

noted in Part 2-1, Section 1, Power

Brake Functional Test. If the brake

booster is damaged or defective, re-

place it with a new booster. The brake

booster is serviced only as an assem-

bly.procarmanuals.com

02-02-07
Brake System

02-02-07

ANTI-SKID CONTROL SYSTEM

RELEASE PAWL CAM PIN

RELEASE PAWL CAM LEVER

RELEASE CABLE

H
1636-
A

FIG. 10—Parking Brake Control Assembly

With Manual Release—Typical

power unit with mounting bracket is

riveted to the control assembly. The

vacuum actuated piston within the

unit is connected by a rod to the

upper end of the release lever (Fig. 9).

The lower end of the release lever ex-

tends out for alternate manual release
in the event of vacuum power failure

or for optional manual release at any

time.

Hoses connect the power unit and

the engine manifold to a vacuum re-

lease valve in the transmission neutral

safety switch.
The anti-skid control system con-

sists of three major components (Fig.

39).
Mechanically driven electromag-

netic sensors at each rear wheel; an

electronic control module mounted

under the glove box; a vacuum pow-

ered actuator attached to a bracket on

the inside of the right front frame rail

under the toe board.

The sensors consist of steel rings

having teeth on their outer diameters,

pressed on each axle shaft just out-

board of the wheel bearing. The teeth

rotate past corresponding teeth on the

inside diameter of stationary steel

rings mounted in the bearing retain-

ers.
Also mounted in the retainers, are

ring-shaped permanent magnets and

coils of wire. Two wires from each

sensor connect the sensors to the con-

trol module.

The control module consists of solid

state electronic components sealed in

a container. It is connected to the sen-

sors and to a solenoid on the actuator.

The actuator is similar to a vacuum

brake booster and consists of three

parts.
A chamber divided by a vacuum

suspended diaphragm; a hydraulic cyl-

inder connected to the diaphragm; and

a solenoid connected electrically to the

control module.

IN-VEHICLE ADJUSTMENTS AND REPAIRS

After any brake service work, ob-

tain a firm brake pedal before moving

the vehicle. Riding the brake pedal

(common on left foot application)

should be avoided when driving the

vehicle.

BRAKE SHOE ADJUSTMENTS—

DRUM BRAKES

The hydraulic drum brakes are

self-adjusting and require a manual

adjustment only after the brake shoes

have been relined, replaced, or when

the length of the adjusting screw has

been changed while performing some

other service operation. The manual

adjustment is performed with the

drums removed, using the tool and the

procedure detailed below.

When adjusting the rear brake

shoes,
check the parking brake cables

for proper adjustment. Make sure that

the equalizer operates freely.
To adjust the brake shoes:

1.
Use Rotunda Tool HRE 8650,

(Fig. 11) to determine the inside diam-

eter of the drum braking surface.

2.
Reverse the tool as shown in Fig.

11 and adjust the brake shoe diameter

to fit the gauge. Hold the automatic

adjusting lever out of engagement

while rotating the adjusting screw, to

prevent burring the screw slots. Make

sure the adjusting screw rotates freely.

If necessary, lubricate the adjusting

screw threads with a thin, uniform

coating of MIC-100-A.

3.
Rotate Tool HRE 8650 around

the brake shoes to be sure of the set-

ting.

4.
Apply a small quantity of high

temperature grease to the points

where the shoes contact the backing

plate, being careful not to get the lu-

bricant on the linings.

5. Install the drums. Install Tinner-

man nuts and tighten securely.

6. Install the wheels on the drums
and tighten the nuts to specification.

7.
Complete the adjustment by

applying the brakes several times with

a minimum of 50 lbs pressure on the

pedal while backing the vehicle. After

each stop the vehicle must be moved

forward.

8. After the brake shoes have been

properly adjusted, check the operation

of the brakes by making several stops

while operating in a forward direction.

WHEEL CYLINDER REPAIR-

DRUM BRAKE

Wheel cylinders should not be di-

sassembled unless they are leaking or

unless new cups and boots are to be

installed. It is not necessary to remove

the brake cylinder from the backing

plate to disassemble, inspect, or hone

and overhaul the cylinder. Removal is

necessary only when the cylinder is

damaged or scored beyond repair.procarmanuals.com

02-02-10
Brake System

02-02-10

brake adjustment then connect the

parking brake cable to the parking

brake lever (Fig. 8).

4.
Install the shoe guide (anchor

pin) plate on the anchor pin when so

equipped.

5.
Place the cable eye over the an-

chor pin with the crimped side toward

the backing plate.

6. Install the primary shoe to an-

chor spring (Fig. 15).

H1391-A

FIG. 75—Retracting Spring

Installation

7.
Install the cable guide on the

secondary shoe web with the flanged

hole fitted into the hole in the second-

ary shoe web. Thread the cable

around the cable guide groove (Fig.

8).

It
is
imperative that
the
cable
be

positioned
in
this groove
and not be-

tween
the
guide
and the
shoe
web.

8.
Install the secondary shoe to an-

chor spring with the tool shown in

Fig. 15.

Be certain that
the
cable
eye is not

cocked
or
binding
on the
anchor
pin

when installed.
All
parts should
be
flat

on
the
anchor
pin.
Remove
the
brake

cylinder clamp.

9. Apply high-temperature grease

(MIC-100-A) to the threads and the

socket end of the adjusting screw.

Turn the adjusting screw into the ad-

justing pivot nut to the limit of the

threads and then back off 1/2 turn.

Interchanging
the
brake shoe
ad-

justing screw assemblies from
one
side

of
the
vehicle
to the
other would cause

the brake shoes
to
retract rather than

expand each time
the
automatic
ad-

justing mechanism operated.
To pre-

vent installation on the wrong side of

the vehicle, the socket end of the ad-

justing screw is stamped with an R or

L (Fig. 16). The adjusting pivot nuts

can be distinguished by the number of

grooves machined around the body of

the nut. Two grooves on the nut indi-

cate a right thread; one groove indi-

cates a left thread.
10.
Place the adjusting socket on

the screw and install this assembly be-

tween the shoe ends with the adjusting

screw toothed wheel nearest the sec-

ondary shoe.

11.
Hook the cable hook into the

hole in the adjusting lever. The adjust-

ing levers are stamped with an R or L

to indicate their installation on right

or left brake assembly (Fig. 16).

12.
Position the hooked end of the

ADJUSTING LEVER

IDENTIFICATION LINES

H1143-C

FIG. 16—Adjusting Screw
and

Lever Identification

adjuster spring completely into the

large hole in the primary shoe web.

The last coil of the spring should be at

the edge of the hole. Connect the loop

end of the spring to the adjuster lever

hole.

13.
Pull the adjuster lever, cable

and automatic adjuster spring down

and toward the rear to engage the

pivot hook in the large hole in the sec-

ondary shoe web (Fig. 8).

14.
After installation, check the ac-

tion of the adjuster by pulling the sec-

tion of the cable between the cable

guide and the anchor pin toward the

secondary shoe web far enough to lift

the lever past a tooth on the adjusting

screw wheel. The lever should snap

into position behind the next tooth,

and release of the cable should cause

the adjuster spring to return the lever

to its original position. This return ac-

tion of the lever will turn the adjusting

screw.one tooth.

If pulling the cable does not pro-

duce the action described, or if the

lever action is sluggish instead of posi-

tive and sharp, check the position of

the lever on the adjusting screw

toothed wheel. With the brake in a

vertical position (anchor at the top),

the lever should contact the adjusting

wheel 3/16 inch (plus or minus 1/32

inch) above the centerline of the

screw. If the contact point is below

this centerline, the lever will not lock

on the teeth in the adjusting screw

wheel, and the screw will not be turned
as the lever is actuated by the cable.

To determine the cause of this con-

dition:

a. Check the cable end fittings. The

cable should completely fill or extend

slightly beyond the crimped section of

the fittings. If it does not meet this

specification, possible damage is indi-

cated and the cable assembly should

be replaced.

b.
Check the cable length. On

Ford, Mercury, Meteor, Thunderbird,

Continental Mark III, and Lincoln

Continental models, the cable should

measure 11 1/8 inches (plus or minus

1/64 inch) from the end of the cable

anchor to the end of the cable hook.

On Fairlane, Montego, Falcon,

Mustang, and Cougar models the

cable should measure 8 13/32 inches

on 9 inch brakes or 9 3/4 inches on

10 inch brakes from the end of the

cable anchor to the end of the cable

hook.

c. Check the cable guide for dam-

age.
The cable groove should be paral-

lel to the shoe web, and the body of

the guide should lie flat against the

web.
Replace the guide if it shows

damage.

d. Check the pivot hook on the

lever. The hook surfaces should be

square with the body of the lever for

proper pivoting. Replace the lever if

the hook shows damage.

e. See that the adjusting; screw

socket is properly seated in the notch

in the shoe web.

WHEEL CYLINDER

DRUM BRAKE

REMOVAL '

1.
Remove the wheel and the drum.

2.
Remove the brake shoe assem-

blies,
following procedures outlined in

this section.

3.
Disconnect the brake line from

the brake cylinder Figs. 17 thru 21.

On
a
vehicle with
a
vacuum brake

booster,
be
sure
the
engine
is
stopped

and there
is no
vacuum
in the
booster

system before disconnecting
the hy-

draulic lines.

To disconnect the hose at a front

cylinder, loosen the tube fitting that

connects the opposite end of the hose

to the brake tube at a bracket on the

frame. Remove the horseshoe-type re-

taining clip from the hose and brack-

et, disengage the hose from the brack-

et, then unscrew the entire hose as-

sembly from the front wheel cylinder.

At a rear cylinder, unscrew the tubeprocarmanuals.com

02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take care
to

avoid loosening
the
bridge bolts that

hold
the two
halves
of the
caliper
to-

gether.

4.
Lift
the
caliper assembly
off the

rotor
and
place
it on the
bench.

Installation

1.
If the
caliper assembly
is to be

replaced, transfer
the
steel tubing
and

the bleeder screw
to the new
caliper.

2.
Position
the
caliper assembly
on

the rotor,
and
mate
the
mounting bolt

holes
in the
caliper with those
in the

spindle.
It may be
necessary
to
push

the caliper pistons into
the
cylinder

bores
to
obtain clearance between
the

shoe
and
lining assembly
and the

rotor.
The
shoe
and
lining assemblies

should
be
seated properly
on the

bridges.

3.
Install
the
caliper
to
spindle
re-

taining bolts
and
torque them
to
spec-

ification. Check
to
insure that
the

rotor runs squarely
and
centrally
be-

tween
the two
halves
of the
caliper.

These should
be
approximately 0.090-

0.120 inch clearance between
the
cali-

per
and the
rotor outside diameter

(Fig.
6).

4.
Position
the
steel transfer tube

brake hose bracket
and
caliper assem-

bly
to the
spindle. Install
the
retaining

bolts then torque them
to
specifica-

tion.

5.
Connect
the
front wheel steel

transfer tube from
the
caliper
to the

front brake hose connector. Check
the

hose
for
proper installation
(Fig. 21).

6. Bleed
the
brake system
and cen-

tralize
the
differential valve
as out-

lined
in
Part
2-1.
Check
the
master

cylinder fluid level
and add the
speci-

fied fluid,
as
required. Pump
the

brake pedal several times
to
actuate

the piston seals
and to
position
the

shoe
and
lining assemblies.

7.
Install
the
wheel
and
tire assem-

bly
and the
wheel cover.

8. Road test
the
vehicle.

DISC BRAKE SHOE
AND

LINING

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire from
the
hub and
rotor assembly.

2.
Remove
the
caliper from
the ve-

hicle following
the
procedures outlined

under Disc Brake Caliper Assembly.

3.
To
facilitate removal
of the
cali-

per assemblies,
the
piston
may
have
to

be pushed into
its
bore. Apply
a

steady inward pressure against
the

inner shoe
and
lining assembly. Main-

tain
the
pressure
for at
least
a
minute.

4.
Slide
the two
outer shoe retain-

ing clips
off the
retaining pins
(Fig.

23).

5.
Remove
the two
retaining pins

from
the
outer shoe, then remove
the

shoe from
the
stationary caliper.

6. Slide
the
inner brake shoe
out-

ward until
it is
free
of the
hold-down

springs, then remove
the
brake shoe.

7.
Remove
the
caliper locating pins

and stabilizer attaching bolts, then
re-

move
and
discard
the
stabilizer
or sta-

bilizers.

8. Remove
the
locating
pin
insula-

tors from
the
anchor plate.

Installation

When installing
new
shoes
and lin-

ings
it
will
be
necessary
to
force
the

piston
to the
bottom
of its
bore.

Apply sufficient pressure
to
overcome

the grip
of the
piston seal
on the pis-

ton.

1.
Install
new
caliper locating
pin

insulators
in the
anchor plate.

2.
Position
the
caliper assembly
in

the anchor plate.

3.
Position
the new
stabilizer
or

stabilizers
and
install
the
caliper locat-

ing pins
to
engage approximately four

threads.

If
the
caliper locating pins
are
rust-

ed
or
corroded they should
be re-

placed.

Apply water
or
isopropyl alcohol
to

the caliper locating pins before instal-

lation.
Oil or
grease must
not be
used

on
the
locating pins.

4.
Position
the
outer brake shoe
on

the caliper
and
install
the two
retain-

ing pins
and
clips.

5.
Install
the
inner brake shoe
so

that
the
ears
of
shoe
are on top of the

anchor plate bosses
and
under
the

shoe hold-down springs.

6. Position
the
shoe
and
lining

assemblies
so
that
the
caliper assem-

bly
can be
placed over
the
rotor.
Ro-

tate
a
hammer handle between
the lin-

ings
to
reset
the
stabilizers.

7.
Install
the
caliper assembly over

the rotor
and on the
spindle. Install

the
two
caliper attaching bolts,
and

torque them
to
specifications.
The

upper bolt must
be
tightened first.
In-

stall
the
safety wire
and
twist
the
ends
at least five turns. Push
the
wire ends

against
the
spindle
to
avoid interfer-

ence with
the
brake hose
and the

steering stop.

8. With moderate pressure applied

to
the
brake pedal, torque
the
stabiliz-

er attaching screws
and
caliper locat-

ing pins
to
specification.

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire
as-

sembly from
the hub and
rotor assem-

bly.
Be
careful
to
avoid damage
or in-

terference with
the
caliper splash

shield, bleeder screw fitting
or
transfer

tube.

2.
Remove
the two
bolts that retain

the caliper splash shield,
and
remove

the shield
(Fig. 4).

3.
To
facilitate removal
and
instal-

lation
of the
shoe
and
lining assem-

blies,
the
pistons must
be
pushed into

their bores. Apply
a
steady inward

pressure against each shoe
and
lining

assembly toward
its
respective caliper

housing
on
each side
of the
rotor
(Fig.

6).
Maintain
the
pressure
for at
least

a minute.
If the
pistons will
not go ifi

easily, force them
in
with water pump

pliers.

4.
Grasp
the
metal flange
on the

outer
end of the
shoe with
two
pairs

of pliers
and
pull
the
shoe
out of the

caliper (Fig.
25).

Installation

1.
Position
a new
shoe
and
lining

assembly
on
each side
of the
rotor
so

that
the
lining faces
the
rotor.
Be
sure

AB

AB

USE SECOND

PAIR
OF

PLIERS HERE

H 1651
A

FIG. 25—Removing Disc Brake

Shoe
and
Lining Assembly—

Lincoln Continentalprocarmanuals.com

02-02-20
Brake System

02-02-20

1.
Disconnect the stoplight switch

wires at the connector. Remove the

spring retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then liftfthe switch straight upward

from the pin. Use care to avoid switch

damage during removal.

2.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

3.
Remove the brake tube from the

primary and secondary outlet ports of

the master cylinder.

4.
Remove the cap screws and lock-

washers that secure the master cylin-

der to the dirSh panel and lift the cyl-

inder forward and upward from the

vehicle.

Installation

1.
Position the boot on the push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening and position

the master cylinder on the panel.

2.
Install the cap screws at the dash

panel and torque them to specifica-

tion.

3.
Coat the nylon bushings with

SAE 10W oil. Install the nylon wash-

er and bushing on the brake pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder leaving the brake line

fittings loose.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top of the dual reservoirs.

Use Ford Brake Fluid— Extra Heavy

Duty-Part Number C6AZ-19542-A

(ESA-M6C25-A) or equivalent for all

drum brake applications. The extra

heavy duty brake system fluid is col-

ored blue for identification. Do not

mix low temperature brake fluids with

the specified fluid for the power disc

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.
FAIRLANE, MONTEGO,

FALCON, MUSTANG AND

COUGAR

Removal

Refer to Figs. 27 and 28.

1.
Working from inside the vehicle

below the instrument panel, disconnect

the master cylinder push rod from the

brake pedal assembly. The push rod

cannot be removed from the master

cylinder.

2.
Disconnect the stoplight switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then lift the switch straight upward

from the pin. Use care to avoid switch

damage during removal.

3.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

4.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder.

5.
Remove the lock nuts or cap

screw and lockwashers that secure the

master cylinder to the dash panel and

lift the cylinder forward and upward

from the car.
Installation

Refer to Figs. 27 and 28.

1.
Position the boot on tie push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening.

2.
On Fairlane, Falcon or Montego

models, position the gasket and mas-

ter cylinder on the mounting studs on

the dash panel. Install the lock nuts

on the studs at the dash panel and

torque them to specification.

3.
On Mustang or Cougar models,

position the gasket and master cylin-

der on the dash panel. Install the re-

taining screws and torque them to

specification. Coat the nylon bushings

with SAE 10W oil. Install the nylon

washer and bushing on the brake

pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder and tighten to speci-

fied torque.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

MASTER CYLINDER

IDENTIFICATION
UPPER STUD

SHAFT (AUTOf/lATIC

TRANSMISSION)

CLIP

BRAKE PEDAL

BUSHING SUPPORT

TUBE-2B253

TUBE-2A040
CLUTCH

PEDA_

LOWER STUD
STOP LITE

SWITCH

/ 13480

MASTER CYLINDER

PUSH ROD
BRAKE PEDAL

H 1556-C

FIG. 27—Dual Master Cylinder Installation—Non Power Brake

Fairlane, Montego, and Falconprocarmanuals.com

02-02-23
Brake System

02-02-23

BOOSTER ASSEMBLY- 2005

NUT-34444-S7

HOSE 2A047

MASTER CYLINDER

IDENTIFICATION

BRAKE TUBE-2263

BRAKE TUBE -2264

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B257
BRAKE TUBE-2B255

H 15S3-B

FIG. 32—Master Cylinder Installation-

Thunderbird and Continental Mark III

FLUID LEVEL IN MASTER

CYLINDER MUST 3E FULL

TO 1/4 INCH FROM TOP
BUSH

SLEEVE

BOLT

BRAKE SWITCH

13480

NUT (4 REQUIRED) -55768-S2

WASHER"(4 REQUIRED) -44726-S8

BOOSTER

ASSEMBLY 2005

MASTER CYLINDER 2WO

HOSE-2A047

BUSHING DIP IN

S.A.E. 10W MOTOR OIL

BEFORE ASSEMBLY

PEDAL ASSEM6LY-2455

COVER

BRAKE TUBE-2A040

REAR BRAKE TUBE -2B329

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B328

FRONT BRAKE TUBE-2B162

PROPORTIONING VALVE

MASTER CYLINDER

IDENTIFICATION

H 1530-C

FIG. 33—Master Cylinder Installation—Lincoln Continental
4.
Connect the shell-wire connector

to the brake warning lamp switch.

Make sure the plastic lugs on the con-

nector hold the connector securely to

the switch.

5. Bleed the brakes and centralize

the pressure differential valve.

PROPORTIONING VALVE

FORD, MERCURY

AND METEOR

On Ford, Mercury and Meteor

models, the proportioning valve must

be removed with the pressure differen-

tial valve. Use the procedure shown

above for replacement of the propor-

tioning valve.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 18.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining the

pressure differential valve bracket to

the fender apron.

3.
Lift the proportioning valve

bracket from behind the pressure dif-

ferential valve bracket and remove the

proportioning valve from the vehicle.

Installation

1.
Position the proportioning valve

and bracket to the fender apron with

the proportioning valve bracket be-

tween the pressure differential valve

bracket and the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the two

valve brackets to the fender apron.

4.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

5.
Bleed the brakes and centralize

the pressure differential valve.

MUSTANG AND COUGAR

Removal

Refer to Fig. 19.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining theprocarmanuals.com

02-02-25
Brake System

02-02-25

clearing the pin. Slide the switch com-

pletely onto the pin, and install the

nylon washer as shown in Figs. 29

thru 33. Be careful not to bend or de-

form the switch. Secure these parts to

the pin with the hairpin retainer. Con-

nect the stop light switch wires to the

connector, and install the wires in the

retaining clip.

BRAKE PEDAL

FORD, MERCURY

AND METEOR

Removal

1.
Disconnect the stop light switch

wires at the connector.

2.
Remove the hairpin retainer.

Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin,

and then lift the switch straight up-

ward from the pin. Be careful not to

damage the switch during removal.

Slide the master cylinder or booster

push rod and the nylon washers and

bushing off the brake pedal pin (Figs.

26 and 29).

3.
Remove the hairpin type retainer

and washer from the brake pedal

shaft, then remove the shaft, the brake

pedal and the bushings from the pedal

support bracket.

Installation

1.
Apply a coating of SAE 10 En-

gine oil to the bushings and locate

bushings in their proper places on the

pedal assembly and pedal support

bracket (Figs. 26 and 29).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft through the support

bracket and brake pedal assembly. In-

stall the retainer.

3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the nylon washer as

shown in Figs. 26 and 29. Be careful

not to bend or deform the switch. Se-

cure these parts to the pin with the

hairpin retainer.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.
5.
Check the Brake Pedal Free

Height and Travel Measurements,

Part 2-1, Section 1.

FAIRLANE, MONTEGO AND

FALCON—MANUAL-SHIFT

TRANSMISSION

Removal

1.
Remove the clutch pedal assist

spring.

2.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

3.
Disconnect the stop light switch

wires at the connector.

4.
Remove the switch retainer, and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.

5. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27 and 30).

6. Remove the self-locking pin and

washer from the clutch and brake

pedal shaft, then remove the clutch

pedal and shaft assembly, the brake

pedal assembly, and the bushings from

the pedal support bracket (Figs. 27

and 30).

Installation

1.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
Position the brake pedal to the

support bracket, then install the clutch

pedal and shaft assembly through the

support bracket and brake pedal as-

sembly. Install the spring clip (Figs.

27 and 30).

3.
Install the clutch pedal assist

spring.

4.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10

engine oil to the bushing.

5.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27 and 30. Secure

these parts to the pin with the
self-

locking pin.
6. Connect the stop light switch

wires to the connector, and install the

wires to the retaining clip.

7.
Adjust the clutch pedal free play

(Group 5) to specification, if required.

8. Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

MUSTANG AND COUGAR—

MANUAL-SHIFT

TRANSMISSION

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
Remove the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

3.
On non-power brakes, remove

the two cap screws retaining the mas-

ter cylinder to the dash panel and re-

move the two cap screws retaining the

brake pedal support bracket to the

dash panel. On power brakes remove

the two cap screws retaining the

booster to the dash panel.

4.
Working inside the vehicle, se-

cure the clutch pedal against the

bumper stop with a small C-clamp as

shown in Figs. 28 and 31.

5.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder or

booster push rod, bushing and nylon

washer from the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Figs. 28 and 31).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel. On power

brakes remove the nuts from the

brake booster studs.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Position the pedal and support

bracket assembly in a vise.

13.
Remove the C-clamp to release

the clutch pedal from its bumper stop

and pivot the pedal away from the

bumper.procarmanuals.com

02-02-26
Brake System

02-02-26

14.
Remove the clutch pedal assist

spring.

15.
On non-power brakes, remove

the retainer clip from the clutch and

brake pedal shaft, then remove the

clutch pedal and shaft assembly, the

brake pedal assembly, and the bush-

ings from the pedal support bracket.

On power brakes, remove the retainer

nut from the brake pedal shaft then

remove the pedal shaft, the brake

pedal assembly and the bushings from

the pedal support bracket.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
On non-power brakes, position

the brake pedal to the pedal support

bracket, then install the clutch pedal

and shaft assembly through the sup-

port bracket and brake pedal assem-

bly. On power brakes position the

brake pedal to the pedal support

bracket, then install the pedal shaft

and nut.

3.
Install the clutch pedal assist

spring and pivot the clutch pedal

against its bumper stop. Secure the

pedal to the stop with a small C-

clamp as shown in Figs. 28 and 31.

4.
Position the pedal support

bracket assembly to the dash panel,

and to the steering column retainer

studs.

5.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two attaching sheet

metal screws. On power brakes install

the nuts on the brake booster studs.

6. Install the two cap screws at-

taching the pedal support bracket to

the upper cowl bracket.

7. Install the cap screw attaching

the pedal support bracket to the top

inner cowl bracket (Figs. 28 and 31).

8. Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the stop light switch so that it

straddles the push rod with the switch

slot on the pedal pin and the switch

outer hole just clearing the pin. Slide

the switch completely onto the pin,

and install the outer nylon washer as

shown in Figs. 28 and 31. Secure

these parts to the pin with the
self-

locking retainer.

9. Connect the stop light switch

wires to the connector.

10.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10
engine oil to the bushing. Remove the

C-clamp from the clutch pedal.

11.
Working from the engine side

of the dash panel, on non-power

brakes, install the two cap screws at-

taching the pedal support bracket to

the dash panel. Then install the two

screws attaching the master cylinder

to the dash panel. On power brakes

install the cap screws retaining the

brake booster to the dash panel.

12.
Install the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

13.
Adjust the clutch pedal free

play (Group 5) to specification, if re-

quired.

14.
Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

15.
Connect the ground cable to the

battery.

FAIRLANE, MONTEGO,

FALCON, MUSTANG

AND COUGAR-

AUTOMATIC TRANSMISSION

Removal

1. Disconnect the stop light switch

wires at the connector.

2.
Remove the self-locking pin and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27, 28, 30 and 31).

3.
On all vehicles except Mustang

and Cougar with power brakes, re-

move the self-locking pin and washer

from the brake pedal shaft, then re-

move the shaft, the brake pedal as-

sembly and the bushings from the

pedal support bracket. On Mustang

and Cougar vehicles with power

brakes, remove the locknut and bolt

from the pedal. Remove the pedal as-

sembly from the support bracket (Fig.

3).

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly and pedal support

bracket (Figs. 27, 28, 30 and 31).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft or bolt through the

support bracket and brake pedal as-

sembly. Install the retainer or locknut.
3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin, and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27, 28, 30 and 31.

Secure these parts to the pin with the

self-locking pin.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

Check the Brake Pedal Free Height

and Travel Measurements, Part 2,

Section 1.

THUNDERBIRD
AND

CONTINENTAL MARK
III

Removal

1.
Loosen the booster mounting

nuts.

2.
Disconnect the stop light switch

wires at the connector.

3.
Remove the hairpin retainer.

Slide the stop light switch off from

the brake pedal pin just far enough

for
the
switch outer hole
to
clear
the

pin,
and then lift the switch straight

upward from the pin. Slide the master

cylinder push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Fig. 32).

4.
Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the pedal support

bracket, and remove the bushings.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly (Fig. 32).

2.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through

the support bracket and brake pedal

assembly. Install the pivot bolt nut

and torque to specifications.

3.
Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, install the

outer nylon washer as shown in Fig.

32.
Secure these parts to the pin with

the hairpin retainer.procarmanuals.com

02-02-27
Brake System

02-02-27

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

5.
Torque the booster mounting

nuts to specifications.

LINCOLN CONTINENTAL

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
It is necessary to obtain clear-

ance to remove vacuum hoses and the

electrical connector to the temperature

heat control box. Remove the two

screws retaining the relay to the fend-

er and push the relay aside. Discon-

nect the vacuum hoses and connector

at the heat control box.

3.
Working under the instrument

panel, disconnect the vacuum hoses,

wires and retaining clip from the tem-

perature heat control box. Remove the

two screws securing the temperature

control box to the dash panel.

4.
Remove the lower control hous-

ing retaining screws (6). Disconnect

the wire harnesses at the lower control

panel and place the panel aside. Re-

move the wire harness shield. Remove

the wire harness clip. Position the

wire harness aside. Remove the tem-

perature control box and position it

aside.

5.
Remove the hair-pin type retain-

er. Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Lift the switch upward from the pin.

Slide the master cylinder push rod,

nylon washers and bushing off the

brake pedal pin.

6. Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the support bracket

and remove the bushings.

7.
If required, remove the brake

pedal pad retaining nuts and remove

the brake pedal pad.

Installation

1.
If the brake pedal pad was re-

moved, position the pad on the pedal.

Install the pad retaining nuts and tor-

que them to specification.

2.
Apply SAE 10 engine oil to the

bushings and locate all the bushings in

their proper places on the pedal as-

sembly.

3.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through
the support bracket and pedal assem-

bly. Install the pivot bolt nut and tor-

que it to specification.

4.
Install the inner nylon washer,the

master cylinder push rod link, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod link with the switch slot on

the pedal and the switch outer hole

just clearing the pin. Install the outer

nylon washer as shown in Fig. 33. In-

stall the hair-pin type retainer on the

brake pedal pin.

5.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

6. Position the wire harness and

clip on the temperature control box

and install the retaining screw. Posi-

tion the temperature control box to

the dash panel and install the two re-

taining bolts.

7.
Connect the vacuum lines and

the electrical connector to the control

box. Position the wire harness to the

control box and install the retaining

clip.

8. Position the wire harness shield

and install two retaining bolts.

9. Connect the wire harnesses to

the lower control panel and install the

retaining screws.

10.
Working within the engine

compartment, connect the wire con-

nector to the temperature heat control

box.

11.
Position the relay to the fender

apron and install the retaining bolts.

12.
Connect the ground cable to the

battery.

13.
Check the brakes and light

switch for proper operation. Close the

hood.

PARKING BRAKE CONTROL

ASSEMBLY

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 34.

1.
Make sure the parking brake is

fully released.

2.
Remove all tension from the rear

cables by backing off the adjusting nut

from the equalizer.

3.
Remove the roll pin that secures

the release knob to the cable and re-

move the knob.

4.
Remove the nut that secures the

release cable to the instrument panel
and remove the cable from the rear of

the instrument panel.

5.
Remove the two nuts attaching

the control assembly to the dash

panel.

6. Remove the cap screw attaching

the control assembly to the cowl side

bracket.

7.
Disconnect the hose to the park-

ing brake vacuum unit, if so equipped.

8. Remove the front cable assembly

retainer clip from the cable assembly

and disconnect the cable ball from the

control clevis.

9. Remove the control assembly

from the vehicle.

Installation

1.
Position the control assembly in

the vehicle.

2.
Fit the cable assembly through

its mounting hole and install the re-

taining clip. Connect the cable ball to

the control clevis.

3.
Connect the vacuum hose to the

parking brake unit, if so equipped.

4.
Install the attaching cap screw to

the cowl side bracket. Do not tighten.

5.
Install the two control assemb-

ly-to-dash panel nuts. Tighten the nuts

and the cap screw to specifications.

6. Insert the release cable into the

instrument panel and install the re-

taining nut.

7.
Install the release knob on the

cable with the roll pin.

8. Check the operation of the park-

ing brake. Adjust the parking brake

as required.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 35.

1.
Make sure the parking brake is

completely released.

2.
Remove all tension from the rear

cables by backing off the jam nut and

adjusting nut from the equalizer.

3.
Working inside the vehicle, re-

move the four bolts and one nut re-

taining the left air vent and cable as-

sembly to the dash and instrument

panels. Remove the vent assembly.

4.
Remove the parking brake front

cable ball retaining clip from the clev-

is.

5.
Disconnect the cable ball from

the notch in the brake clevis.

6. Remove the three screws that at-

tach the control assembly to the left

cowl inner side panel.procarmanuals.com

02-02-39
Brake System

02-02-39

MAJOR REPAIR OPERATIONS

BRAKE DRUM REFINISHING

Minor scores on a brake drum can

be removed with sandpaper. A drum

that is excessively scored or shows a

total indicator runout of over 0.007

inch should be turned down. Remove

only enough stock to eliminate the

scores and true up the drum. The refi-

nished diameter must not exceed 0.060

inch oversize.

Check the inside diameter of the

brake drum with a brake drum mi-

crometer (Tool FRE-14^1).

If the drum diameter is less than

0.030 inch oversize after refinishing^

standard lining may be installed. If

the drum diameter is 0.030—0.060

inch oversize after refinishing, oversize

lining must be installed.

After a drum is turned down, wipe

the refinished surface with a cloth

soaked in clean denatured alcohol. If

one drum is turned down, the opposite

drum on the same axle should also be

cut down to the same size.

ROTOR REFINISHING

Rotunda Disc Brake Attachment,

FRE-2249-2, is the only recommended

tool to refinish the disc brake rotors.

The step-by-step resurfacing procedure

provided with the tool must be ad-

hered to.

The finished braking surfaces of the

rotor must be flat and parallel within

0.0007 inch; lateral runout must not

exceed 0.003 inch total indicator read-

ing, and the surface finish of the brak-

ing surfaces are to be 80/15 micro

inches. The minimum limiting dimen-

sions (Figs. 11 and 12, Part 2-1) from

the inboard bearing cup to the out-

board rotor face and from the inboard

bearing cup to the inboard rotor face

must be observed when removing ma-

terial from the rotor braking surfaces.

On all models except Lincoln Con-

tinental, the limiting dimensions are to

be measured with a ball and gage bar

(Rotunda Kit FRE-70160).

BRAKE SHOE RELINING

Brake linings that are worn to with-

in 1/32 inch of the rivet head or are

less than 0.030 inch thick (bonded lin-

ing) or have been contaminated with

brake fluid, grease or oil must be re-

placed. Failure to replace worn linings

will result in a scored drum. When it
is necessary to replace linings, they

must also be replaced on the wheel on

the opposite side of the vehicle.

Inspect brake shoes for distortion,

cracks, or looseness. If this condition

exists,
the shoe must be discarded. Do

not attempt to repair a defective brake

shoe.

1.
Wash the brake shoes thoroughly

in a clean solvent. Remove all burrs

or rough spots from the shoes.

2.
Check the inside diameter of the

brake drum with a brake drum mi-

crometer (tool FRE-1431). If the di-

ameter is less than 0.030 inches over-

size,
standard lining may be installed.

If the diameter is 0.030—0.060 inches

oversize, oversize lining should be in-

stalled.

3.
Position the new lining on the

shoe.
Starting in the center, insert and

secure the rivets, working alternately

towards each end. Replacement lin-

ings are ground and no further grind-

ing is required.

4.
Check the clearance between the

shoe and lining. The lining must seat

tightly against the shoe with not more

than 0.008 inch clearance between any

two rivets.

RETAINER - 2B245
DUAL MASTER CYLINDER

DISASSEMBLY

1.
Clean the outside of the master

cylinder and remove the filler cover

and diaphragm. Pour out any brake

fluid that remains in the cylinder. Dis-

card the old brake fluid.

2.*
Remove the secondary piston

stop bolt from the bottom of the cyl-

inder (Figs. 40 and 41).

3.
Remove the bleed screw, iL re-

quired.

4.
Depress the primary piston and

remove the snap ring from the retain-

ing groove at the rear of the master

cylinder bore (Fig. 42). Remove the

push rod and the primary piston as-

sembly from the master cylinder bore.

Do not remove the screw that retains

the primary return spring retainer, re-

turn spring, primary cup and protec-

tor on the primary piston. This assem-

bly is factory pre-adjusted and should

not be disassembled.

5.
Remove the secondary piston as-

sembly. Do not remove the outlet tube

seats,
outlet check valves and outlet

SECONDARY SYSTEM

BRAKE OUTLET
COVER -2166

GASKET-2167

MASTER CYLINDER -2155

SNAP RING -7821

BOOT

PUSH ROD

PRIMARY PISTON

ASSEMBLY - 2169

tTUBE SEAT-

2B220
* SECONDARY PISTON

ASSEMBLY - 2A502

• NOT USED ON POWER BRAKE EQUIPPED VEHICLES

fNOT SERVICED

•REPLACE AS AN ASSEMBLY ONLY

H 1499-B

FIG. 40— Dual Master Cylinder Disassembled—Except Disc Brakesprocarmanuals.com