FORD MUSTANG 1997 4.G Workshop Manual

49
*
[AS44230(MBC )08/95]
q
Using the ªSCANº function with your
cassette tape player
*
[AS44240(MBC )03/96]
Press the ªSCAN/TUNEº button to enter the
scan mode (display indicates ªSCNº).
Pushing the right
aside of the ªSEEKº
button will begin the forward scan mode on
the tape currently playing, stopping on each
tape selection for approximately an
eight-second sampling.
*
[AS44250(MBC )03/96]
Pushing the left
bside of the ªSEEKº
button will begin the reverse scan mode,
stopping on each previous tape selection for
approximately an eight-second sampling.
While scanning, the display indicates whirling
sprockets plus an ªSºm.
*
[AS44260(MBC )03/96]
To stop the scan mode on the presently
sampled tape selection, press the
ªSCAN/TUNEº button again.
*
[AS44270(MBC )08/95]
q
How to change the side of the tape being
played
[AS44280(MBC )02/95]
The alternate side of the tape can be selected
at any time by pressing the ªPLAY/PROGº
button.
*
[AS44300(MBC )08/95]
How to eject the tape
*
[AS44310(MBC )08/95]
To stop the tape and eject the cassette, press the
ªEJCTº button. The radio will resume playing if
the radio power is on. The tape cartridge can be
ejected with radio power (and/or ignition) on or
off.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

50
*
[AS44320(MBC )08/95]
How to store the tape
*
[AS44330(MBC )08/95]
Press the ªAM/FMº button to stop the tape
player and resume radio play. The cassette will
be stored in the tape player and the
Xsymbol
in the display will be lit until you push the
ªPLAY PROGº button to resume tape play. Fast
forward and fast rewind can be used while the
tape is in storage mode without interrupting
radio play.
*
[AS44340(MBC )02/96]
Using the DolbyHB noise reduction feature
*
[AS44350(MBC )09/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
*
[AS44360(MBC )04/95]
Push thekbutton to activate Dolby B Noise
Reduction. Push again to deactivate.
*
[AS44490(MBC )08/95]
Tape error messages
*
[AS44500(MBC )08/95]
Your cassette tape player is equipped to
diagnose certain problems you may experience.
Error codes are as follows:
*
[AS44510(MBC )08/95]
Error 0Ð Communication error between the
radio controller and the tape controller. The
cassette player will eject the tape. Insert the tape
again. If the same error code appears, turn the
ignition off, then back on again and insert the
tape.
*
[AS44520(MBC )08/95]
Error 1Ð Possible problem cartridge. The
cassette tape player will eject the tape. Insert the
tape again. If the same error code appears in the
display, try a different cartridge.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

51
*
[AS44530(MBC )08/95]
Error 2Ð Tape eject or load failure. Your
cassette tape player will go into the pause mode.
Push ªEJCTº to eject the tape. If the tape doesn't
eject, refer the problem to qualified personnel for
service.
*
[AS44540(MBC )04/96]
Tips on Caring for the Cassette Player and
Tapes
*
[AS44550(MBC )08/95]
In order to keep your cassette tape player
performing the way it was meant to, read and
follow these simple precautions:
*
[AS44560(MBC )04/96]
q
Using a Ford Cassette Cleaning Cartridge or
equivalent to clean the tape player head after
10-12 hours of play will help maintain the
best playback sound and proper tape
operation.
*
[AS44570(MBC )08/95]
q
Only cassettes that are 90 minutes long or
less should be used. Tapes longer than 90
minutes are thinner and subject to breakage
or may jam the tape player mechanism.
*
[AS44580(MBC )08/95]
q
Protect cassettes from exposure to direct
sunlight, high humidity and extreme heat or
cold. If they are exposed to extreme
conditions, allow them to reach a moderate
temperature before playing.
*
[AS44590(MBC )08/95]
q
Loose labels on cassette tapes can become
lodged in the mechanism. Remove any loose
label material before inserting cassette.
*
[AS44600(MBC )08/95]
q
Do not leave a tape in the cassette tape
player. High heat in the vehicle can cause the
cassette to warp.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

52
*
[AS60900( ALL)04/96]
Common Radio Reception
Conditions
*
[AS61000( ALL)08/95]
Several conditions prevent FM reception from
being completely clear and noise-free, such as
the following:
*
[AS61100( ALL)08/95]
1. Distance/Strength
*
[AS61200( ALL)08/95]
The strength of the FM signal is directly related
to the distance the signal must travel. The
listenable range of an average FM signal is
approximately 25 miles (40 kilometers). Beyond
this distance, the radio is operating in a fringe
area and the signal becomes weaker.
*
[AS61300( ALL)04/96]
NOTE: Always make sure your antenna is
fully extended to the maximum length
for proper reception. If your antenna is
not fully extended, you may experience
signal loss while traveling in fringe
reception areas.
*
[AS61400( ALL)08/95]
2. Terrain
*
[AS61500( ALL)08/95]
The terrain (hilly, mountainous, tall buildings) of
the area over which the signal travels may
prevent the FM signal from being noise-free.
*
[AS61700( ALL)08/95]
If there is a building or large structure between
the antenna and station, some of the signal
ªbendsº around the building, but certain spots
receive almost no signal. Moving out of the
ªshadowº of the structure will allow the station
to return to normal.
*
[AS61800( ALL)08/95]
When the radio waves are reflected off objects or
structures, the reflected signal cancels the normal
signal, causing the antenna to pick up noise and
distortion. Cancellation effects are most
prominent in metropolitan areas, but also can
become quite severe in hilly terrain and
depressed roadways.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

53
*
[AS61900( ALL)08/95]
To minimize these conditions, a stereo/mono
blend circuit has been incorporated into this
system. This feature automatically switches a
weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS62000( ALL)08/95]
Several sources of static are normal conditions
on AM frequencies. These can be caused by
power lines, electric fences, traffic lights and
thunderstorms.
*
[AS62100( ALL)08/95]
Another reception phenomenon isStrong Signal
Capture and Overload. This can occur when
listening to a weak station and when passing
another broadcast tower. The close station may
capture the more distant station, although the
displayed frequency does not change. While
passing the tower, the station may switch back
and forth a few times before returning to the
original station.
*
[AS62200( ALL)03/96]
When several broadcast towers are present
(common in metropolitan areas), several stations
may overload the receiver, resulting in
considerable station changing, mixing and
distortion.
*
[AS62300( ALL)08/95]
Automatic gain control circuitry for both AM
and FM bands has been incorporated into this
system to reduce strong signal capture and
overload.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

54
%*
[AS62400( ALL)08/95]
All About Radio Frequencies
*
[AS62500( ALL)08/95]
The Federal Communications Commission (FCC)
and the Canadian Radio Telecommunications
Commission (CRTC) establish the frequencies
that AM and FM radio stations may use for
their broadcasts. The allowable frequencies are,
AM: 530, 540...1600, 1610 kHz in 10 kHz steps;
FM: 87.9, 88.1...107.7, 107.9 MHz in 0.2 MHz
steps.
*
[AS62600( ALL)08/95]
Not all frequencies will be assigned to a given
area. This radio will tune to each of these
frequencies using manual tune and no fine
tuning is necessary as radio stations may not use
other frequencies.
*
[AS62700( ALL)08/95]
Some FM radio stations advertise a
ªrounded-offº frequency which is not the
frequency they actually broadcast on. For
example, a radio station that is assigned a
frequency of 98.7 MHz may call itself ªRadio 99º
even though 99.0 MHz is not an allowable FM
broadcast frequency.
%
*
[AS62800( ALL)08/95]
Important Warranty and Service
Information
*
[AS62900( ALL)07/90]
q
Warranty
*
[AS63000( ALL)08/95]
Your sound system is warranted for three years
or 36,000 miles (60,000 kilometers), whichever
comes first. Consult your vehicle warranty
booklet for further information. Ask your dealer
for a copy of this limited warranty.
*
[AS63200( ALL)07/90]
q
Service
*
[AS63300( ALL)04/96]
At Ford, we stand behind our audio systems
with a comprehensive service and repair
program. If anything should go wrong with
your Ford audio system, return to your dealer
for service. There is a nationwide network of
qualified Ford authorized repair centers to assist
you.
File:04rcasm.ex
Update:Mon Feb 24 10:13:07 1997

55
Controls and Features
%*
[CF00200( ALL)01/96]
The main controls for the climate control system,
clock, and radio are on the instrument panel.
%*
[CF00300( ALL)03/96]
NOTE: Any cleaner or polish that increases the
gloss (shine) of the upper part of the
instrument panel should be avoided.
The dull finish in this area is to help
protect the driver from undesirable
windshield reflection.
*
[CF00400( ALL)05/96]
Your vehicle has a variety of features designed
for your comfort, convenience and safety. Read
this chapter to find out about standard and
optional features.
%
*
[CF00500( ALL)03/96]
The Climate Control Systems
[CF00600( ALL)12/95]
Your vehicle has one of two different climate
control systems. The two systems are:
[CF00700(M )04/96]
q
a heating and air conditioning system
[CF00800(M )04/96]
q
a heating only system
*
[CF01200( ALL)12/95]
If you are not sure which system your vehicle
has, see the diagrams on the following pages.
% [CF01300(M )04/96]
The Heating and Air Conditioning
System (If equipped)
[CF01400(M )05/96]
You can heat the inside of your vehicle, defrost
the windshield, and turn on the air conditioning
with the three controls in the center of the
instrument panel:
[CF01500(M )12/95]
q
FAN
[CF01600(M )12/95]
q
TEMP
[CF01700(M )12/95]
q
SELECT
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

56 [CF01800(M )05/96]
quarter page art:0010180-IThe controls for the optional heating and air conditioning
system
[CF01900(M )12/95]
The heating system in the optional heating and
air conditioning system operates the same as the
heater only system. SeeThe Heater Only System.
[CF02000(M )05/96]
To cool your vehicle quickly in warm weather,
turn the SELECT control to MAX A/C, turn the
TEMP control all the way to the end of the blue
range (full left) and turn the FAN control to HI.
MAX A/C uses recirculated air and is the most
fuel efficient way to cool your vehicle and can
also be used in heavy traffic to prevent exhaust
fumes from entering the vehicle. MAX A/C can
also be used in high humidity areas for more
efficient operation.
[CF02100(M )12/95]
If the interior of your vehicle is very warm,
drive for the first few minutes with the windows
open. This forces most of the hot, stale air out of
the vehicle and allows the air conditioning to
work faster.
% [CF02200(M )05/96]
To cool your vehicle using outside air, turn the
SELECT control to NORM A/C, turn the TEMP
control all the way to the end of the blue range
(full left) and turn the FAN control to the
desired speed between LO and HI. NORM A/C
provides quieter system operation than MAX
A/C.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

57 [CF02300(M )04/96]
Under normal conditions, the SELECT control
should be left in any position other than MAX
A/C or OFF when the vehicle is parked. This
allows the vehicle to ªbreatheº through the
outside air inlet duct.
% [CF02400(M )04/96]
The Heater Only System (If equipped)
[CF02500(M )05/96]
You can heat the inside of your vehicle, defrost
the windshield, or use the vents by adjusting the
three controls in the center of the instrument
panel:
[CF02600(M )12/95]
q
FAN
[CF02700(M )12/95]
q
TEMP
[CF02800(M )12/95]
q
SELECT
[CF02900(M )05/96]
quarter page art:0010177-J
The controls for the standard heating only system
[CF03000(M )05/96]
To heat the inside of your vehicle, turn the
SELECT control to FLOOR, turn the TEMP
control all the way to the end of the red range
(full right) and turn the FAN control to HI.
After the vehicle is warm, the temperature and
blower speed can be adjusted to maintain a
comfortable temperature.
% [CF03100(M )05/96]
To defrost the windshield and side windows,
turn the SELECT control to Defrost symbol, turn
the TEMP control to the end of the red range
(full right) and turn the FAN control to HI.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

58 [CF03200(M )05/96]To heat the inside of your vehicle and defrost
the windshield and side windows at the same
time, turn the SELECT control to MIX, turn the
TEMP control into the red range, as required,
and turn the FAN control to the desired speed
between LO and HI.
% [CF03300(M )05/96]
On mild days you may want to ventilate your
vehicle with outside air. Turn the SELECT
control to VENT, turn the TEMP control to the
end of the blue range (full left) and turn the
FAN control to the desired speed. Air will be
delivered through the instrument panel registers.
[CF03400(M )05/96]
Under normal conditions, the SELECT control
should be left in any position except OFF when
the vehicle is parked. This allows the vehicle to
ªbreatheº through the outside air inlet duct.
%
*
[CF14400(MBC )03/96]
Rear Window Defroster
(If equipped)
*
[CF14600( ALL)03/96]
The defroster for the rear window clears frost,
fog, or thin ice from both the inside and outside
of the rear window.
[CF14700(M )05/96]
The control for the rear window defroster is
located on the left side of the instrument panel
below the headlamp switch.
[CF14800(M )05/96]
one third page art:0010189-C
The control for the rear window defroster
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997