FORD MUSTANG 2003 Workshop Manual

Valve spring installed height 42.3-
42.9 mm (1.67- 1.69 in) Valve spring installed pressure 283.0-
321.0 N @ 42.56 mm (63.61 lb @ 1.68 in) Roller follower ratio —
intake 2.02:1
Roller follower ratio —
exhaust 2.03:1
Hydraulic Lash Adjuster
Diameter 16.000-
15.988 mm (0.6299- 0.6294 in) Clearance-
to-bore 0.018-
0.069 mm (0.0007- 0.0027 in) Service limit 15.988 mm
Hydraulic leakdown rate
c 5-
25 seconds Collapsed lash adjuster gap —
desired 0.45-
0.85 mm (0.02- 0.03 in) Camshaft
Theoretical valve lift @ 0 lash —
intake 13.00 mm (0.51 in)
Theoretical valve lift @ 0 lash —
exhaust 13.75 mm (0.54 in)
Lobe lift —
intake 7.11038 mm (0.28 in)
Lobe lift —
exhaust 7.4794 mm (0.30 in)
Allowable lobe lift loss 0 mm (0.0 in)
Journal diameter 26.962-
26.936 mm (1.0615- 1.0605 in) Camshaft journal bore inside diameter 27.012-
26.987 mm (1.0635- 1.0625 in) Camshaft journal-
to-bearing clearance 0.025-
0.076 mm (0.00098- 0.002992 in) Camshaft journal-
to-bearing clearance —
service limit 0.100 mm (0.003937 in) max.
Runout —
Front and rear journals 0.03 mm (0.001 in)
Runout —
four inner journals 0.09 mm (0.003 in)
End play 0.027-
0.190 mm (0.001- 0.007 in) End play —
service limit 0.190 mm (0.007480 in)
Cylinder Block
Cylinder bore diameter 31 mm (1.24 in) from top of block
red — 90.200-90.210
blue — 90.210-90.220
yellow — 90.220-90.230 Cylinder bore maximum taper 0.70 mm (0.027559 in)
Cylinder bore maximum out-of-
round —limit 0.20 mm (0.007874 in)
Cylinder bore maximum out-of-
round —service
limit 0.70 mm (0.027559 in)
Main bearing bore inside diameter 72.400-
72.424 mm (2.8504- 2.8513 in) Crankshaft
Main bearing journal diameter 67.482-
67.504 mm (2.66- 21.661 in) Main bearing journal maximum taper 0.004 mm (0.0002 in)
Main bearing journal maximum out-of-
round 0.05 mm (0.002 in)
Main bearing journal-
to-cylinder block clearance
— desired 0.025-
0.044 mm (0.001- 0.002 in) Main bearing journal-
to-cylinder block clearance
— allowable 0.025-
0.050 mm (0.00098- 0.00197 in) Connecting rod journal diameter 52.983-
53.003 mm (2.085941- 2.086728 in) Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
With installation of a new filter.
b Distance front edge of bearing is installed below front face of cylinder block.
c Time necessary for plunger to leak down 1.6 mm of travel with 222 N force and leak down fluid in
tappet.
d Measured at 31.5 mm from top of block. Measured at 43 mm from top of piston, at 90 degrees to the
piston pin. Connecting rod journal maximum taper 0.004 mm (0.0002 in)
Connecting rod journal maximum out-of-
round 0.05 mm (0.002 in)
Crankshaft maximum end play 0.075-
0.377 mm (0.003- 0.015 in) Piston and Connecting Rod
Piston diameter —
code red 1 d 90.185-
90.205 mm (3.55- 3.551 in) Piston diameter —
code blue 2 d 90.195-
90.215 mm (3.55- 3.551 in) Piston diameter —
code yellow 3 d 90.205-
90.225 mm (3.551- 3.552 in) Piston-
to-cylinder bore clearance -0.005-
0.025 mm (- 0.002/+0.001 in) Piston ring end gap —
compression (top) e 0.130-
0.280 mm (0.005- 0.011 in) Piston ring end gap —
compression (bottom) e 0.300-
0.550 mm (0.0018- 0.0022 in) Piston ring end gap —
oil ring (steel rail) e 0.150-
0.650 mm (0.006- 0.0256 in) Piston ring groove width —
compression (top) 1.530-
1.550 mm (0.06- 0.061 in) Piston ring groove width —
compression
(bottom) 1.520-
1.540 mm (0.06- 0.061 in) Piston ring groove width —
oil ring 3.030-
3.050 mm (0.12- 0.12 in) Piston ring width —
compression (top) 1.480-
1.500 mm (0.058- 0.059 in) Piston ring width —
compression (bottom) 1.470-
1.490 mm (0.0587- 0.0586 in) Piston ring-
to-groove clearance — compression
(top) 0.050-
0.090 mm (0.002- 0.004 in) Piston ring-
to-groove clearance — compression
(bottom) 0.030-
0.080 mm (0.00118- 0.00315 in) Piston ring-
to-groove clearance — oil ring Snug fit
Piston pin bore diameter
f 21.008-
22.014 mm (0.866- 0.867 in) Piston pin diameter 22.0010-
22.0030 mm (0.87- 0.871 in) Piston pin length 61.601-
62.030 mm (2.42523- 2.44212 in) Piston pin-
to-piston fit -
0.005/+0.0135 mm (- 0.0002/+0.0005 in) Piston-
to-connecting rod clearance — standard 0.009-
0.0235 mm (0.0004- 0.00092 in) Piston-
to-connecting rod clearance — service
limit 0.035 mm (0.001378 in)
Connecting rod-
to-pin clearance 0.009-
0.023 mm (0.0004- 0.0009 in) Connecting rod pin bore diameter 22.012-
22.024 mm (0.86661- 0.86708 in) Connecting rod length (center-
to-center) 150.7 mm (5.933 in)
Connecting rod maximum allowed bend
g 0.038 per 25 mm (0.00150 per 0.9843 in)
Connecting rod maximum allowed twist
c 0.050 per 25 mm (0.00197 per 0.9843 in)
Connecting rod bearing bore diameter 56.866-
56.886 mm (2.23881- 2.23960 in) Connecting rod bearing-
to-crankshaft clearance 0.027-
0.069 mm (0.0010629- 0.0027165 in) Connecting rod side clearance —
standard 0.125-
0.475 mm (0.005- 0.019 in) Connecting rod side clearance —
service limit 0.50 mm (0.01969 in) max. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

e
Specification in 90.200 mm diameter gauge.
f If applicable, measured vertically, +0.030- 0.050 mm (0.001-0.002 inch) measured horizontally (oval
pin bore).
g Pin bore and crank bearing bore must be parallel and in same vertical plane within the specified total
difference when measured at the ends of a 203 mm bar, 101.5 mm on each side of rod centerline.
Torque Specifications Description Nm lb-
ft lb-
in Main bearing cap adjusting bolts
a — — —
EGR sensor bracket 10 — 89
Belt idler pulley 25 18 —
Oil filter 15 11 —
Oil filter adapter insert 58 43 —
Camshaft sprocket bolt
a — — —
Connecting rod bolt
a — — —
Engine mount nuts 150 111 —
Engine mount-
to-cylinder block bolts 70 52 —
Exhaust manifolds
a — — —
Engine front cover bolts
a — — —
Drive belt tensioner bolts 25 18 —
A/C muffler 20 15 —
Battery cable support brackets 20 15 —
Cylinder head bolt
a — — —
Pulley-
to-crankshaft bolt a — — —
EGR valve to intake manifold 25 18 —
EGR valve tube to exhaust manifold fittings 40 30 —
Intake manifold-
to-cylinder head bolt 25 18 —
Main bearing cap bolt
a — — —
Oil filter adapter bolts 25 18 —
Oil level indicator tube bolt 10 — 89
Oil pump screen cover and tube-
to-oil pump bolt 10 — 89
Oil pan-to-
cylinder block bolt a — — —
Flywheel 80 59
Oil pan-to-
engine front cover bolts a — — —
Oil pump-
to-cylinder block bolt 10 — 89
Oil pump screen cover and tube-
to-main bearing cap stud spacer bolt 25 18 —
Water pump pulley bolts 25 18 —
Cam cover bolt
a — — —
Water pump-
to-cylinder block bolt 25 18 —
Water bypass tube 25 18 —
EGR tube nuts (2 req'd) 40 30 —
Power steering pump to engine 25 18 — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
Refer to the procedure in this section. Power steering reservoir bolts 10 — 89
Water outlet connector bolts 25 18 —
Camshaft cap cluster to cylinder head bolts 10 — 89
Torque converter nuts 25 18 —
Timing chain tensioner bolts 25 18 —
Transmission filler tube bolt 47 35 —
A/C compressor bolts 25 18 —
Ignition coil bolts 6 — 53
Generator brace bolts 10 — 89
Primary timing chain guide-
to-engine bolts 10 — 89
Accelerator cable bracket bolts 10 — 89
Rear seal retainer bolts 10 — 89
Pressure plate bolts 2 — 47
Spark plugs 18 13 —
Crankshaft timing bolt sensor assembly 10 — 89
Camshaft timing bolt sensor assembly 10 — 89
Fuel rail studs 10 — 89
Engine coolant sensor 15 11 —
Exhaust manifold—
stud to cylinder head 10-
13 7-10 —
Throttle body adaptor bolts
a — — —
Throttle body bolts 10 — 89
Idle air control valve 10 — 89
RFI capacitor nut 10 — 89
Generator bolts 25 18 —
Oil pan drain plug 14 10 —
Water bypass tube bracket bolt 25 18 —
Subframe bolts 115 85 —
Battery lead to generator 10 — 89
EGR vacuum regulator solenoid bracket 10 — 89
Pipe plug—
water drain 20 15 —
Screen and cover assembly to main bearing cap stud spacer 25 18 —
Wiring harness retainer nut 10 — 89
Oil pressure switch
a — — —
A/C muffler stud to cylinder head 10 — 89
EGR tube to exhaust manifold connector 50 37 — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Klj . 6 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Klj . 2 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Item Part Number Description
1 6150 Piston ring
2 6159 Piston ring
3 6159 Piston ring
4 6110 Piston
5 6135 Piston pin
6 6211 Connecting rod bearing
7 6214 Connecting rod bolt
8 6152 Piston ring Klj . 3 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9 6161 Piston ring
10 6200 Connecting rod assy.
11 6100 Piston and rod assy (8 req'd)
12 N806164 Washer
13 6256 Camshaft sprocket
14 6265 Camshaft sprocket spacer
15 6766 Oil filler cap
16 6C324 Crankcase vent connector and hose
17 6582 Valve cover
18 6B280 Camshaft bearing cap
19 6250 Camshaft
20 9H308 Idle air control valve inlet tube
21 N806155 Bolt (2 req'd)
22 9F715 Idle air control valve
23 N806154 Bolt (4 req'd)
24 9F670 Idle air control gasket
25 9E926 Throttle body
26 9E936 Throttle body gasket
27 9A589 Throttle body gasket
28 N807309 Bolt (3 req'd)
29 9728 Bracket
30 N806154 Bolt (5 req'd)
31 9D476 EGR valve gasket
32 9D460 EGR valve
33 W701625 Bolt (2 req'd)
34 N811017 Stud bolt (4 req'd)
35 9F792 Fuel injection supply manifold
36 9D477 EGR valve to exhaust manifold tube
37 9E498 Main emission vacuum control connector
38 12A522 Engine control sensor extension wire
39 N806459 Dowel (4 req'd)
40 8555 Water bypass tube
41 N646419 Dowel (2 req'd)
42 W623454 Washer (2 req'd)
43 N806040 Dowel (2 req'd)
44 N806007 Dowel (2 req'd)
45 6A636 Oil filter adapter gasket
46 6881 Oil filter adapter (manual transmission)
47 N806156 Bolt (4 req'd)
48 6714 Oil bypass filter
49 N87838 Dowel
50 Klj . 4 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6754 Oil level indicator tube
51 N806155 Bolt
52 N806139 Bolt
53 6750 Oil level dipstick
54 N811363 Bolt (2 req'd)
55 18198A Engine lifting eye
56 9430 Exhaust manifold
57 9448 Exhaust manifold gasket
58 6049 Cylinder head, RH
59 12405 Spark plug
60 W701681 Stud (8 req'd)
61 W701706 Nut (8 req'd)
62 6051 Head gasket
63 N807071 Bolt
64 10153 Generator mounting bracket
65 N811011 Bolt (2 req'd)
66 8549 Water outlet connector
67 10884 Water temperature indicator sender unit
68 N808130 Bolt (9 req'd)
69 N806807 O-
ring 70 N807309 Bolt (2 req'd)
71 12A366 Coil on plug (8 req'd)
72 9F593 Fuel injector
73 8575 Water thermostat
74 9424 Intake manifold
75 N806139 Bolt
76 N806164 Washer
77 6256 Camshaft sprocket
78 6265 Camshaft sprocket spacer
79 N807352 Bolt (4 req'd)
80 6A505 Valve cover
81 6758 Crankcase ventilation tube
82 N806070 Bolt (24 req'd)
83 6B280 Camshaft bearing cap
84 N806282 Bolt (4 req'd)
85 N807173 Bolt (2 req'd)
86 N808102 Bolt
87 19A216 Belt idler pulley
88 10300 Generator
89 N804178 Nut (2 req'd)
90 19A439 Bracket
91 Klj . 5 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...