sensor FORD MUSTANG 2003 Workshop Manual

Item Part Number Description
1 N808102 Bolt
2 N808102 Bolt
3 19A216 Belt idler pulley
4 N806155 Bolt
5 6B288 Camshaft position sensor
6 N606543 Bolt (4 req'd)
7 6L266 Timing chain tensioner
8 W705803 Stud Klj . 9 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9 6268 Timing chain (2 req'd)
10 6K297 Timing chain guide
11 6268 Timing chain (2 req'd)
12 6M269 Timing chain tensioner
13 6L253 Timing chain tensioner arm
14 N605893 Bolt (4 req'd)
15 6K297 Timing chain guide
16 N804958 Bolt (2 req'd)
17 6L253 Timing chain tensioner arm
18 6306 Crankshaft sprocket
19 12A227 Ignition pulse ring
20 3A696 Power steering pump
21 N806176 Bolt (4 req'd)
22 3R801 Gasket
23 3A696 Power steering pump pulley
24 W706508 Stud
25 N806177 Bolt (8 req'd)
26 N808586 Stud
27 N806300 Stud (4 req'd)
28 6700 Crankshaft front seal
29 N806155 Bolt
30 6C315 Crankshaft position sensor
31 W706560 Stud
32 6C086 Engine front cover
33 N806165 Washer
34 N806139 Bolt
35 19A216 Belt Idler Pulley
36 6316 Crankshaft pulley Klj . 10 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11 N620482 Dowel
12 87836 Plug
Item Part Number Description
1 N807198 Dowel pin (2 req'd)
2 N807309 Bolt
3 N807959 Bolt
4 18663 Heater water hose
5 W500110 Bolt (2 req'd)
6 12A699 Knock sensor (2 req'd)
7 N807309 Bolt (2 req'd)
8 18696 Heater water hose
9 7120 Pilot bearing
10 6K318 Crankshaft rear retainer
11 N806155 Bolt (6 req'd)
12 6310 Crankshaft oil slinger
13 6375 Flexplate
14 N806168 Bolt (6 req'd)
15 — Flywheel
16 N808139 Bolt (8 req'd)
17 7550 Clutch disc
18 7563 Clutch pressure plate
19 N808969 Bolt (6 req'd)
20 6701 Crankshaft rear oil seal
21 N806007 Dowel pin (2 req'd) Klj . 13 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Intake Manifold — Upper
Removal 1. Remove the air intake scoop bracket. For additonal information, refer to Section 303 - 12 .
2. Remove the air cleaner outlet tube. For additional information, refer to Section 303 - 12 .
3. Disconnect the accelerator cable, the speed control actuator cable and the return spring.
4. Remove the bolts, disconnect the clip and position the cables out of the way.
5. Disconnect the throttle position (TP) sensor. 6. Disconnect the evaporative emissions (EVAP) return hose. SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Connect the EVAP return hose.
10. Connect the TP sensor.
11. Position the cables and bracket. zInstall the bolts, connect the clip.
12. Connect the throttle cable, the speed control actuator cable and throttle return spring. Klj . 6 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Intake Manifold — Lower
Removal 1. Remove the upper intake manifold. For additional information, refer to Intake Manifold — Upper
in this section.
2. Disconnect the fuel line. For additional information, refer to Section 310 - 00 .
3. Remove the coolant by- pass tube. For additional information, refer to Section 303 - 03A .
4. Remove the generator. For additional information, refer to Section 414 - 02 .
5. Disconnect the electrical connector and the vacuum line from the fuel pressure sensor.
6. Disconnect the eight fuel injector electrical connectors.
7. Separate the fuel charging wiring harness from the fuel injection supply manifold studs in three places.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or equivalent WSE-
M5B392- A Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Connect the electrical connector and the vacuum line to the fuel pressure sensor.
7. Install the generator. For additional information, refer to
Section 414 - 02 .
8. Install the coolant bypass tube. For additional information, refer to Section 303 - 03A .
9. Connect the fuel line. For additional information, refer to Section 310 - 00 .
10. Install the upper intake manifold. For additional information, refer to Intake Manifold — Upper in
this section. Klj . 4 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

power steering pump aside.
23. Remove the A/C muffler bracket nut.
24. Remove the bolts and position the A/C compressor aside.
25. Disconnect the crankshaft position (CKP) sensor electrical connector.
26. Remove the wiring harness nuts and position the wiring harness aside. Klj . 6 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

35. Remove the three bolts and position the power steering reservoir and bracket assembly aside.
36. Disconnect the camshaft position (CMP) sensor electrical connector.
37. Remove the idler pulleys.
38. Remove the bolts and the studs and remove the engine front cover. Klj . 9 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Install the idler pulleys.
5. Connect the camshaft position (CMP) sensor electrical connector.
6. Position the power steering reservoir and bracket assembly and install the bolts.
7. Install the coolant pump pulley and the bolts. 1.25 x 16
13 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 14 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 15 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 Klj . 12 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...