tire type FORD MUSTANG 2003 Workshop Manual

Vehicle Certification (VC) Label Reference
Paint Codes Item Description
1 Exterior paint color code
2 Region code
3 Special order code
(DSO —
domestic special order
FSO — foreign special order
PTO — paint, tire option special order) 4 Brake type code
5 Interior trim code
6 Tape/paint stripe code
7 Radio type code
8 Axle ratio code
9 Transmission code
10 Spring code
11 Powertrain calibration code Klj . 6 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4920/S3B~us~en~ ...

„
Loudness proportional to vehicle speed. Low- frequency noise at high
speeds, noise and loudness increase with speed. GO to Symptom Chart —
Driveline Noise/Vibration .
„ A low- pitched noise (drumming). GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of acceleration or
deceleration. GO to Symptom Chart — Tire Noise/Vibration .
„ Noise varies with wind/vehicle speed and direction. GO to Symptom Chart — Air Leak and Wind Noise .
„ Related to engine speed.
„Noise varies with engine rpm. GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of engine speed
(rpm).
2. Acceleration
„Wide open throttle (WOT)
„Engine induced contact between components. Inspect and repair as
necessary.
„ Noise is continuous throughout WOT. Exhaust system or engine ground
out. GO to Symptom Chart — Engine Noise/Vibration .
„ Light/moderate acceleration
„Tip- in moan. Engine/exhaust noise. GO to Symptom Chart — Engine
Noise/Vibration .
„ Knock-type noise. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline shudder. GO to Symptom Chart — Driveline Noise/Vibration .
„ Engine vibration. GO to Symptom Chart — Engine Noise/Vibration .
3. Turning noise. GO to Symptom Chart — Steering Noise/Vibration .
4. Braking
„Clicking sound is signaling ABS is active. Acceptable ABS sound.
„ A continuous grinding/squeal. GO to Symptom Chart — Brake Noise/Vibration .
„ Brake vibration/shudder. GO to Symptom Chart — Brake Noise/Vibration .
5. Clutching
„A noise occurring during clutch operation. GO to Symptom Chart — Transmission
(Manual) and Transfer Case Noise/Vibration .
„ Vibration. GO to Symptom Chart — Transmission (Manual) and Transfer Case
Noise/Vibration .
6. Shifting
„Noise or vibration condition related to the transmission (automatic). GO to
Symptom Chart — Transmission (Automatic) Noise/Vibration .
„ Noise or vibration related to the transmission (manual). GO to Symptom Chart —
Transmission (Manual) and Transfer Case Noise/Vibration .
7. Engaged in four- wheel drive. GO to Symptom Chart — Transmission (Manual) and
Transfer Case Noise/Vibration .
8. Cruising speeds
„Accelerator pedal vibration. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline vibration. GO to Symptom Chart — Driveline Noise/Vibration .
„ A shimmy or shake. GO to Symptom Chart — Tire Noise/Vibration .
9. Driving at low/medium speeds Klj . 11 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

condition. It may not always be necessary to follow a pinpoint test to its conclusion. Carry out only the
steps necessary to correct the condition. Then, test the system for normal operation. Sometimes, it is
necessary to remove various vehicle components to gain access to the component requiring testing.
Reinstall all components after verifying system operation is normal.
PINPOINT TEST A: BRAKE VIBRATION/SHUDDER
Test Step Result / Action to Take
A1 ROAD TEST THE VEHICLE—
LIGHT BRAKING z
Check that the wheel and tires are correct for the vehicle.
Inspect the tires for abnormal wear patterns.
z Road test the vehicle. Warm the brakes by slowing the vehicle
a few times from 80– 32 km/h (50 to 20 mph) using light braking
applications. At highway speeds of 89–97 km/h (55- 60 mph),
apply the brake using a light pedal force.
z Is there a vibration/shudder felt in the steering wheel, seat
or brake pedal? Yes
GO to
A4 .
No
GO to A2 .
A2 ROAD TEST THE VEHICLE—
MODERATE TO HEAVY
BRAKING z
Road test the vehicle. At highway speeds of 89–97 km/h (55- 60
mph), apply the brake using a moderate to heavy pedal force.
z Is there a vibration/shudder? Yes
For vehicles with ABS,
GO to
A3 . For vehicles
with standard brakes,
GO to A4 .
No
Vehicle is OK. VERIFY
condition with customer.
TEST the vehicle for
normal operation. A3 NORMAL ACTUATION OF THE ABS SYSTEM DIAGNOSIS
z
During moderate to heavy braking, noise from the hydraulic
control unit (HCU) and pulsation in the brake pedal can be
observed. Pedal pulsation coupled with noise during heavy
braking or on loose gravel, bumps, wet or snowy surfaces is
acceptable and indicates correct functioning of the ABS
system. Pedal pulsation or steering wheel nibble, (frequency is
proportioned to the vehicle speed) indicates a concern with a
brake or suspension component.
z Is the vibration/shudder vehicle speed sensitive? Yes
GO to
A5 .
No
The brake system is
operating correctly. A4 APPLICATION OF THE PARKING BRAKE
z
NOTE: Begin at the front of the vehicle unless the vibration or
shudder has been isolated to the rear.
z This test is not applicable to vehicles with drum- in-hat type
parking brakes. For vehicles with drum- in-hat parking brakes,
proceed to the next test. For all other vehicles, apply the
parking brake to identify if the problem is in the front or rear
brake. At highway speeds of 89–97 km/h (55- 60 mph), lightly
apply the parking brake until the vehicle slows down. Release
the parking brake immediately after the test.
z Is there a vibration/shudder? Yes
GO to
A7 .
No
GO to A5 .
A5 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in this section.
z Are the wheel bearings OK? Yes
GO to
A6 . Klj . 48 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. While the noise is occurring, either place an EngineEAR probe near the IAC valve and the inlet
tube, or create a 6.35 mm (0.25 in)- 12.7 mm (0.50 in) air gap between the inlet tube and the
clean air tube. If the IAC valve is making the noise, install a new IAC valve.
5. Test the vehicle for normal operation.
Steering Gear Grunt/Shudder Test
1. Start and run the vehicle to operating temperature.
2. Set engine idle speed to 1200 rpm.
3. CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Rotate the steering wheel to the RH stop, then turn the steering wheel 90° back from that
position. Turn the steering wheel slowly in a 15° to 30° arc.
4. Turn the steering wheel another 90°. Turn the steering wheel slowly in a 15° to 30° arc.
5. Repeat the test with power steering fluid at different temperatures.
6. If a light grunt is heard or a low (50- 200 Hz) shudder is present, this is a normal steering system
condition.
7. If a loud grunt is heard, or a strong shudder is felt, fill and purge the power steering system.
Checking Tooth Contact Pattern and Condition of the Ring and Pinion
There are two basic types of conditions that will produce ring and pinion noise. The first type is a howl
or chuckle produced by broken, cracked, chipped, scored or forcibly damaged gear teeth and is
usually quite audible over the entire speed range. The second type of ring and pinion noise pertains to
the mesh pattern of the gear pattern. This gear noise can be recognized as it produces a cycling pitch
or whine. Ring and pinion noise tends to peak in a narrow speed range or ranges, and will tend to
remain constant in pitch.
1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Drain the axle lubricant. Refer to Section 205 - 02A for Ford 7.5 rear axles or
Section 205 - 02B for
Ford 8.8 integral axles.
3. Remove the carrier assembly or the axle housing cover depending on the axle type. Refer to Section 205 - 02A for Ford 7.5 rear axles or
Section 205 - 02B for Ford 8.8 integral axles.
4. Inspect the gear set for scoring or damage. Klj . 64 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. For vehicles with a two-
piece hub and brake disc assembly:
z Match-mark before disassembly.
z Remove the brake disc.
z Clean the hub and brake disc mounting surfaces with metal surface cleaner.
z Using a die grinder with a mild abrasive (Scotch Brite® type), remove any rust or
corrosion from the hub and brake disc mounting surfaces.
z Align the match- marks and reinstall the brake disc on the hub.
7. CAUTION: Do not use a bench lathe to machine brake discs.
NOTE: The depth of cut must be between 0.10 and 0.20 mm (0.004 and 0.008 inch). Lighter
cuts will cause heat and wear. Heavier cuts will cause poor brake disc surface finish.
Using an on- car brake lathe, machine the brake discs. Follow the manufacturer's instructions.
After machining, make sure the brake disc still meets the thickness specification.
8. Using the special tools, verify that the brake disc lateral runout is now within specification. For additional information, refer to Section 206 - 00 .
9. Remove the special tool hub adapter.
10. Remove any remaining metal chips from the machining operation.
11. For vehicles with a two- piece hub and brake disc assembly:
z Remove the brake disc from the hub.
z Remove any remaining metal chips from hub and brake disc mounting surfaces and from
the ABS sensor.
z Apply a liberal amount of lubricant to the hub flange, pilot area and to the brake disc- to-
hub mounting surface.
z Using the match marks, mount the brake disc on the hub.
12. Install the brake caliper anchor plate and the brake caliper.
13. Install the tire and wheel assembly.
14. Test the system for normal operation. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Safety Precautions
WARNING: Never run the engine with one wheel off the ground, for example, when
changing a tire. The wheel(s) resting on the ground could cause the vehicle to move.
WARNING: The tire and wheel must always be correctly matched. It is very important to
determine the size of each component before any assembly operations commence. Failure to
adhere to these instructions can result in an explosive separation and cause serious bodily
injury or death.
WARNING: Aftermarket aerosol tire sealants are extremely flammable. Always question
the customer to make sure these products have not been used.
WARNING: Aftermarket wheel assemblies may not be compatible with the vehicle. Use of
incompatible wheel assemblies can result in equipment failure and possible injury. Use only
approved wheel assemblies.
WARNING: Use only wheels and wheel nuts that have been designed for current model
year Ford trucks. Aftermarket wheels or wheel nuts may not fit or function correctly, and can
cause personal injury or damage the vehicle.
WARNING: Always wear safety goggles or a face shield when performing any work with
tire and wheel assemblies.
CAUTION: Do not clean aluminum wheels with steel wool, abrasive- type cleaners or
strong detergents. Use Custom Bright Metal Cleaner 8A-19522- A or equivalent meeting Ford
specifications ESR- M5B194-B.
CAUTION: Reduce the air pressure as much as possible by pushing the valve core
plunger in prior to removing the valve core. Avoid working in a position in which the face or
body is directly over a tire in which there is pressure.
When performing any inspection or repair procedures on wheels (1007/1015) and tires, follow the
preceding safety precautions. SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Wheels And Tires
WARNING: Do not mix different types of tires, such as radial, bias, or bias- belted, on the
same vehicle except in emergencies. Vehicle handling can be seriously affected and can result
in loss of control.
Factory-installed tires and wheels are designed to operate satisfactorily with loads up to and including
full- rated load capacity when inflated to recommended inflation pressures.
Tire and Wheel Runout
Excessive radial and lateral runout of a wheel and tire assembly can cause roughness, vibration,
wheel tramp, tire wear, and steering wheel tremor.
Before checking runout, and to avoid false readings caused by temporary flat spots in the tires, check
runout only after the vehicle has been driven far enough to warm the tires. For additional information,
refer to Section 100 - 04 .
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Wheels And Tires
Inspection and Verification
WARNING: A vehicle equipped with a Traction- Lok® differential will always have both
wheels driving. If, while the vehicle is being serviced, only one wheel is raised off the ground
and the rear axle is driven by the engine, the wheel on the ground could drive the vehicle off
the stand or jack. Be sure both rear wheels are off the ground.
WARNING: Never run the engine with one wheel off the ground, for example, when
changing a tire. The wheel(s) resting on the ground could cause the vehicle to move.
WARNING: Do not balance the wheels and tires while they are mounted on the vehicle.
Possible tire disintegration or differential failure could result, causing personal injury and
extensive component damage. Use off- vehicle wheel and tire balancer only.
Be sure to follow the warnings when carrying out inspection and verification.
Road Test
Verify the customer concern by carrying out a road test on a smooth road. If any vibrations are
apparent, refer to Section 100 - 04 .
To maximize tire performance, inspect for signs of incorrect inflation and uneven wear, which may
indicate a need for balancing, rotation, or front suspension alignment.
Correct tire pressure and driving techniques have an important influence on tire life. Heavy cornering,
excessively rapid acceleration and unnecessary sharp braking increases tire wear.
Replacement tires must follow the recommended:
ztire sizes.
z speed rating.
z load range.
z tire construction type.
Use of any other tire size or type can seriously affect:
zride.
z handling.
z speedometer/odometer calibration.
z vehicle ground clearance.
z tire clearance between the body and chassis.
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Inspection and Verification
Certain axle noise or vibration symptoms are also common to the engine, transmission, wheel
bearings, tires, and other parts of the vehicle. For this reason, be sure that the cause of the trouble is
in the axle before disassembling, adjusting or repairing the axle. Refer to
Section 100 - 04 .
Certain driveshaft vibration symptoms are common to the front engine accessory drive (FEAD), the
engine, transmission or tires. Be sure the cause of the concern is the driveshaft before repairing or
installing a new driveshaft. Refer to Section 100 - 04 .
Certain symptoms may be caused by Traction- Lok® differentials (4026). Check the vehicle certification
label and axle identification tag to determine the type of differential. Refer to Section 100 - 01 .
Noise Acceptability
NOTE: A gear-driven unit will produce a certain amount of noise. Some noise is acceptable and
audible at certain speeds or under various driving conditions such as a newly paved blacktop road.
Slight noise is not detrimental to the operation of the axle and is considered normal.
With the Traction- Lok® differential axle, slight chatter noise on slow turns after extended highway
driving is considered acceptable and has no detrimental effect on the locking axle function.
Universal Joint (U- Joint) Inspection
Place the vehicle on a frame hoist and rotate the driveshaft (4602) by hand. Check for rough operation
or seized U- joints. Install a new U- joint if it shows signs of seizure, excessive wear, or incorrect
seating. Refer to Section 205 - 01 .
Analysis of Leakage
Clean up the leaking area enough to identify the exact source. An axle leak can be caused by the
following. zAxle lubricant level is too high.
z Worn or damaged axle shaft seals or differential seals.
z Differential housing is cracked.
z Flange yoke seat is worn or damaged.
z Pinion flange is scored or damaged.
z Axle cover is not sealed.
z Vent is plugged. Klj . 2 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
If the axle shaft assembly is removed, check runout of the shaft itself. The forged (unmachined)
part of the shaft is allowed to have as much as 3.0 mm (0.120 inch) runout. This alone will not cause a
vibration condition.
1. Position the special tool on the wheel hub or axle flange face, as close to the outer edge as possible. Zero the indicator to allow the pointer to deflect either way.
2. Rotate the hub or flange one full turn and note the maximum and minimum readings. The difference between the maximum and minimum readings will be the total face runout. The
runout must not exceed 0.127 mm (0.005 inch).
Drive Pinion Stem and Pinion Flange
Check the pinion flange runout when all other checks have failed to show the cause of vibration.
One cause of excessive pinion flange runout is incorrect installation of the axle drive pinion seal.
Check to see if the spring on the seal lip has been dislodged before installing the ring gear and pinion.
Axle Noise
NOTE: Before disassembling the axle to diagnose and correct gear noise, eliminate the tires, exhaust,
trim items, roof racks, axle shafts and wheel bearings as possible causes. Follow the diagnostic
procedures in Section 100 - 04 .
The noises described as follows usually have specific causes that can be diagnosed by observation as
the unit is disassembled. The initial clues are the type of noise heard during the road test.
Gear Howl and Whine
Howling or whining of the ring gear and pinion is due to an incorrect gear pattern, gear damage or
incorrect bearing preload.
Bearing Whine
Bearing whine is a high- pitched sound similar to a whistle. It is usually caused by worn/damaged
pinion bearings, which are operating at driveshaft speed. Bearing noise occurs at all driving speeds.
This distinguishes it from gear whine which usually comes and goes as speed changes.
As noted, pinion bearings make a high- pitched, whistling noise, usually at all speeds. If however there
is only one pinion bearing that is worn/damaged, the noise may vary in different driving phases. If
pinion bearings are scored or damaged or there is a specific pinion bearing noise, new pinion bearings
must be installed. A worn/damaged bearing will normally be obvious at disassembly. Examine the
large end of the rollers for wear. If the pinion bearings original blend radius has worn to a sharp edge, a new pinion bearing must be installed. Klj . 6 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...