GEELY FC 2008 Workshop Manual

Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble.
Instructions comes when necessary.
zThe replace procedure are the same, left and right side.
zReferring to the drawing of front combination light on
page 286
1. Replace front fog light bulb
(a) Disassemble front fog light seal cap
(b) Press front fog light bulb spring
(c) Disassemble the bulb
Adjustments
1. Adjust front fog light optic axis
(a) Tyre pressure limits to regular number values.
(b) Start the engine.
(c) Adjust fog light optic axis by turning the optic axis adjust-
able button on the vertical direction.
 290 

Light--Side turning light
Side turning light
Components
Side turning light
 291 

Light--Rear combination light
Rear combination light (LH)
Components
Left rear combination light Bulb
 292 

Light--Rear combination light
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286
1. Disassemble left rear combination light assembly [67000108]
(a) Disassemble three bolts and rear combination light.
(b) Disassemble two bulbs
 293 

Light--Rear fog light
Rear fog light
Components
 294 
Rear fog light jointLeft rear fog light
Bulb

Light--Rear fog light
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure is the same on the left and right side.
zReferring to the drawing of front combination light on page 286
1. Disassemble rear fog light.
(a) Disassemble two bolts.
(b) Disassemble rear fog light by using vice screw driver
 295 

Light--Number plate light
Number plate light
Change
1. Disassemble key aperture of trunk cover and bracket
2. Disassemble number plate light of trunk cover
3. Disassemble number plate light assemble [68000097]
(a) Disassemble the joints.
(b) Disassemble number plate light using vice screw driver.
Clues on: Before using vice screw driver, its cusp
should enwind adhesive tape.
(c) Disassemble the bulb.
 296 
Fixing
claw

High brake light assembly
Change
1. Disassemble high brake light assembly [67010008]
(a) Loosen two fixed jaw just as drawing.
(b) Loosen two fixed jaw and disassemble high brake light
assembly as the drawing, then take the joint apart.
Light--High brake light assembly
 297 
Fixing claw

Light--Left combination switch
Left combination switch
Change
1. Disassemble decorative board under steering column [67000129]
2. Disassemble left combination switch assembly [67000078]
(a) Take the joint apart.
(b) Loosen fixed jaw and pull left combination switch assembly.
Fixing
claw
 298 

Malfunction
Wiper and cleaner do not work.
Wiper does not work on LO, HI or MIST.
Wiper does not work on INT
Washer generator does not work
When cleaner switch ON, wiper does not
work.
Wiper cleaner can not spout
zRight assembled switch on HI, wiper
blade will touch the bodywork.
zWhen right combination switches are OFF, washer will
not return to original position or stop position is incorrect.
Component names
1. ignition switch
2. ignition relay
3. (wiper) fuse (central power distribution box)
4. right assembled switch
5. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. (washer) fuse (central power distribution box)
2. wiper switch
3. wiper generator
4. wiring harness
1. right assembled switch
2. washer generator
3. wiring harness
1. cleaner hose and nozzle
1. right assembled switch *1
2. wiring harnessReference pages
-
-
-
302
302
303
302
303
-
-
-
-
302
303
-
-
302
-
Inspect the car
Inspect the function of cleaner generator
(1) Add some rinsing to wiper water tank, then disassemble
cleaner generator joint.
(2) Connect battery wire with cleaner generator joint terminal2,
negative wire with terminal1,then inspect whether cleaner
generator works.
Notes: Be quick(in 20 seconds) to do this test to pre-
vent cleaner generator coil from burning.
If its function does not in accord with regulations, replace
cleaner generator.
Wiper and cleaner--Wiper and cleaner system
Wiper and cleaner
Wiper and cleaner system
Malfunction phenomena table
The underside table can help you to eliminating malfunction in wiring. It sorts as possibilities of malfunction’s
reasons.
*1:inspect set position of wiper arm and wiper blade.
 299