GEELY MK 2008 Workshop Manual

Chapter 6 SRS (Supplemental Restraint System)Section 1 SRS-General InformationI. Precaution for service For safe reasons, read the following precaution before starting any operation.
1. When servicing the SRS, correct sequence and items are described in the following chapter.
2. Instruments and special tools recommended in this chapter shall be used for operation.
3. When servicing the following components, replace them with the new ones if there is a failure.
(1) SRS ECU
(2) Clock Spring Module
(3) Driver Airbag Module
(4) Passenger Airbag Assembly
(5) Front Seat Belt Pretensioner
4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the
abnormal wire harness in accordance with Table 1.pin1 pin15
pin29
pin16SRS (Supplemental Restraint System)-SRS-General Information5-54No Designation
1 Belt-pretensioner, Driver, Low
2 Belt-pretensioner, Driver, High
3 Belt-pretensioner, Passenger, High
4 Belt-pretensioner, Passenger, Low
5 IGN
6 GND
7WL
9K
10 DAB Hi
11 DAB Lo
13 (Optional) PAB Hi
14 (Optional) PAB Lo
27 Crash Output ECU Terminal Description5. Servicing operation shall be carried out 60s after the negative(-) terminal cable is disconnected from the battery.
In addition, the disconnected negative (-) terminal cable shall be protected with insulating tape for insulation. In

Instrument Designation Usage
Diagnostic detector (Hi-DS T Scan meter)
Special diagnostic meterCheck system troubles of the SRS,
and clear the DTC of ECUIII. Troubleshooting1. Basic process of trouble diagnosis
DTC of the present fault may coexist with that of the history fault.
Notice:

After the new SRS ECU is installed, the warning light of the SRS, with the ignition switch ON, will be on
for 4s and then go out permanently, indicating SRS works normal. In this case, no service is needed. Otherwise,
system diagnosis and service shall be carried out.
If with the ignition switch ON, the warning light of the SRS is not on, the relevant circuits of the warning
light shall be serviced. Then go on with the operation and enable it to work.SRS (Supplemental Restraint System)-
SRS-General Information5-55order to deploy an airbag within a certain time period after the battery
is disconnected, condenser in the ECU shall retain some electrical
energy. Otherwise, it could lead to a serious accident because of the
unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock
springassembly, etc shall be removed and kept in place to avoid the
effects of overheat. (Over 93)
7. When the SRS is serviced, a diagnostic scan meter is used to clear
the DTC to enable the normal work ofthe warning light.II. Test instrumentWarning light con-
stantly goes onuse scanner find out the troubletroubleshootingtrouble eliminated Check SRS warning light (see the right figure)
(1) Turn the ignition switch ON and find out whether the warning
light is on.
(2) 4 seconds after the process of ON-OFF, confirm that the
warning light goes out permanently.
(3) Otherwise, diagnosis and checking have to be involved in.
2. System Diagnosis
The SRS ECU will perform a series of circular diagnostic tests to check the readiness of the SRS functions.
This test can avoid unexpected explosion of the restrain system and in the same time ensure the necessary explosion
in a crash. If a trouble is detected, the SRS ECU will store a proper DTC and turn on the warning light indicating
a trouble for service.SRS Air Bag
Warning LightBattery
Cable Insulation BandSRS Air Bag
Warning Light

No. Problem Description DTC Code
1 There are problems in the Airbag ECU 93C1
2 The power supply voltage of the Airbag ECU is too high 93C2
3 The power supply voltage of the Airbag ECU is too low 93C3
4 The drive side airbag module resistance is too high 93C4
5 The drive side airbag module resistance is too low 93C5
6 The drive side airbag module is short to ground 93C6
7 The drive side airbag module is short to power supply 93C7
8 The passenger side airbag module resistance is too high 93C8
9 The passenger side airbag module resistance is too low 93C9
10 The passenger side airbag module is short to ground 93CA
11 The passenger side airbag module is short to power supply 93CB
12 The driver side pretensioner seat belt resistance is too high 93CC
13 The driver side pretensioner seat belt resistance is too low 93CD
14 The driver side pretensioner seat belt resistance is short to ground 93CE
15 The driver side pretensioner seat belt resistance is short to power supply 93CF
16 The passenger side pretensioner seat belt resistance is too high 93D0
17 The passenger side pretensioner seat belt resistance is too low 93D1
18 The passenger side pretensioner seat belt resistance is short to ground 93D2
19 The passenger side pretensioner seat belt resistance is short to power supply 93D3
20Airbag ECU warning light is short to ground or warning light wire harness is disconnected93D4
21 Airbag ECU warning light is short to power supply 93D5
22 There are problems in the configuration of the airbag ECU 93D6
23The impact signal output interface of the airbag ECU is short to ground or the impact
93D7
output circuit is disconnected.
(1) The airbag controller has internal problem (DTC 93C1): when using diagnostic scan tool to test the airbag
controller, if the DTC code is 93C1, it indicates that there are problems in the controller.5-563. Trouble Identification
Trouble Record (DTC storage)
Each DTC consists of two bytes, indicating current problem or occurred problem. 93CX or 93DX indicates
current problem while 938X or 939X indicates occurred problem. Current problem can not be cancelled, even if
it is cancelled at that time, it will reoccur after initialization or a cycle of self-check. You have to make analysis
on the causes and perform troubleshooting.
The DTC is transmitted by the diagnostic scan tool instructed by ECU through the serial data interface of the
program.
Step Operation Yes No
1 When using the scan tool to test the controller, is the DTC 93C1? Go to step 2 other
2 Use new controller to replace faulty controller Go to step 3
3 After the ignition switch is closed, the warning light shall goes off. Go to step 4 Go to step 1
4 The fault has been removed, use the scan tool to eliminate the DTC.SRS (Supplemental Restraint System)-SRS-General Information

(2) The power supply voltage is too high (DTC 93C2)
When using the scan tool to test the airbag ECU, the DTC is 93C2, indicating that the airbag ECU power supply
voltage is too high, the voltage is higher than 18V.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C3? Go to step 2 other
2Shut off the power supply, check whether the power supply voltage is low?Go to step 4 Go to step 3
3 Go to step 4
4 Go to step 5 Go to step 1
5 The fault has been removed, use the scan tool to eliminate the DTC.
(3) The power supply voltage is too low (DTC 93C3)
When using the scan tool to test the airbag ECU, the DTC is 93C3, indicating that the airbag ECU power supply
voltage is too low, the voltage is lower than 8.5V.
(4) The drive side airbag module resistance is too high (DTC 93C4)5-57Analyze the causes of low power supply voltage, check whether the power
supply of the airbag ECU is low? (check the connection of the wire harness)
After the troubleshooting, switch on the power supply,observe the status of
the warning light. The warning light shall goes off after lighting up for 4
seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C4? Go to step 2 other
2 Go to step 3 Go to step 6
3 Go to step 4 Go to step 6
4 Whether the driver side front airbag module resistance is ok? Go to step 5 Go to step 6
5 Whether the clock spring is ok? Go to step 6
6 Go to step 7 Go to step 1
7 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector of the airbag
controller is well plugged (whether the wire harness connector is in good
condition)?
Disconnect the battery negative cable for 30 seconds, check whether the
driver side front airbag module is well connected? Whether the clock spring
is well connected? (whether the wire harness connector is in good condition)
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C2? Go to step 2 other
2Shut off the power supply, check whether the power supply voltage is high?Go to step 4 Go to step 3
3 Check the connection of the airbag ECU power supply wire harness. Go to step 4
4 Go to step 5 Go to step 1
5 The fault has been removed, use the scan tool to eliminate the DTC.After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).SRS (Supplemental Restraint System)-SRS-General Information

When using the scan tool to test the airbag ECU, the DTC is 93C4, indicating that the driver side front airbag
module resistance is too high, the resistance is higher than 7.0 ohm.
(5) The drive side airbag module resistance is too low (DTC 93C5)
When using the scan tool to test the airbag ECU, the DTC is 93C5, indicating that the driver side airbag module
resistance is too low, the resistance is lower than 2.1 ohm.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C5? Go to step 2 other
2 Go to step 3 Go to step 6
3 Go to step 4 Go to step 6
4 Whether the driver side airbag module resistance is ok? Go to step 5 Go to step 6
5 Whether the clock spring is ok? Go to step 6
6 Go to step 7 Go to step 1
7 The fault has been removed, use the scan tool to eliminate the DTC.
(6) The drive side airbag module is short to ground (DTC 93C6)
When using the scan tool to test the airbag ECU, the DTC is 93C6, indicating that the driver side airbag module
is short to ground, the resistance is lower than 6.5K ohm.5-58Shut off the power supply, check whether the connector of the airbag
controller is well plugged (whether the wire harness connector is in good
condition)?
Disconnect the battery negative cable for 30 seconds, check whether the
driver side front airbag module is well connected? Whether the clock spring
is well connected? (whether the wire harness connector is in good condition)
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C6? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Whether the clock spring is ok? Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector wire harness of
the airbag ECU is in good condition?
Disconnect the battery negative cable for 60 seconds, check whether the
connector wire harness of driver side airbag module is in good condition?
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check). (7) The drive side airbag module is short to power supply (DTC 93C7)
When using the scan tool to test the airbag ECU, the DTC is 93C7, indicating that the driver side airbag module
is short to power supply, the resistance is lower than 21K ohm.SRS (Supplemental Restraint System)-SRS-General Information

(9) The passenger side airbag module resistance is too low
When using the scan tool to test the airbag ECU, the DTC is 93C9, indicating that the passenger side airbag
module resistance is too low, the resistance is lower than 1.2 ohm.5-59Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C7? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Whether the clock spring is ok? Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector wire harness of
the airbag ECU is in good condition?
Disconnect the battery negative cable for 30 seconds, check whether the
connector wire harness of driver side airbag module is in good condition?After the troubleshooting, switch on the power supply, observe the status of the warning
light. The warning light shall goes off after lighting up for 4 seconds (self-check). (8) The passenger side airbag module resistance is too high (DTC 93C8)
When using the scan tool to test the airbag ECU, the DTC is 93C8, indicating that the passenger side airbag
module resistance is too high, the resistance is higher than 4.5 ohm.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C8? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Whether the passenger side airbag module resistance is ok? Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector of the airbag ECU
is well plugged (whether the wire harness connector is in good condition)?
Disconnect the battery negative cable for 30 seconds, check whether the
passenger side airbag module is well connected? (whether the wire
harness connector is in good condition)After the troubleshooting, switch on the power supply, observe the status of the warning
light. The warning light shall goes off after lighting up for 4 seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93C9? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Whether the passenger side airbag module resistance is ok? Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector of the airbag ECU
is well plugged (whether the wire harness connector is in good condition)?
Disconnect the battery negative cable for 30 seconds, check whether the
passenger side airbag module is well connected? (whether the wire
harness connector is in good condition)After the troubleshooting, switch on the power supply, observe the status of the warning
light. The warning light shall goes off after lighting up for 4 seconds (self-check).SRS (Supplemental Restraint System)-
SRS-General Information

(11) The passenger side airbag module is short to power supply (DTC 93CB)
When using the scan tool to test the airbag ECU, the DTC is 93CB, indicating that the passenger side airbag
module is short to power supply, the resistance is lower than 21K ohm.
(12) The driver side pretensioner seat belt resistance is too high (DTC 93CC)
When using the scan tool to test the airbag ECU, the DTC is 93CC, indicating that the driver side pretensioner
seat belt resistance is too high, the resistance is higher than 4.5 ohm.
(13) The driver side pretensioner seat belt resistance is too low (DTC 93CD)
When using the scan tool to test the airbag ECU, the DTC is 93CD, indicating that the driver side pretensioner
seat belt resistance is too low, the resistance is lower than 1.2 ohm.
(14) The driver side pretensioner seat belt resistance is short to ground (DTC 93CE)
When using the scan tool to test the airbag ECU, the DTC is 93CE, indicating that the driver side pretensioner
seat belt is short to ground, the resistance is lower than 6.5K ohm.
(15) The driver side pretensioner seat belt resistance is short to power supply (DTC 93CF)
When using the scan tool to test the airbag ECU, the DTC is 93CF, indicating that the driver side pretensioner
seat belt is short to power supply, the resistance is lower than 21K ohm.5-60 (10) The passenger side airbag module is short to ground
When using the scan tool to test the airbag ECU, the DTC is 93CA, indicating that the passenger side airbag
module is short to ground, the resistance is lower than 6.5K ohm.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93CA? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Whether the passenger side airbag module resistance is ok? Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector wire harness of
the airbag ECU is in good condition?Disconnect the battery negative cable for 30 seconds, check whether the
connector wire harness of passenger side airbag module is in good condition?After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93CB? Go to step 2 other
2 Go to step 3 Go to step 4
3Go to step 4
4 Go to step 5 Go to step 1
5 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the connector wire harness of
the airbag ECU is in good condition?Disconnect the battery negative cable for 30 seconds, check whether the
connector wire harness of passenger side airbag module is in good condition?After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).SRS (Supplemental Restraint System)-SRS-General Information

(21) Airbag ECU warning light is short to power supply (DTC 93D5)
When using the scan tool to test the airbag ECU, the DTC is 93D5, indicating that the airbag ECU warning
light is short to power supply.5-61 (16) The passenger side pretensioner seat belt resistance is too high (DTC 93D0)
When using the scan tool to test the airbag ECU, the DTC is 93D0, indicating that the passenger side
pretensioner seat belt resistance is too high, the resistance is higher than 4.5 ohm.
(17) The passenger side pretensioner seat belt resistance is too low (DTC 93D1)
When using the scan tool to test the airbag ECU, the DTC is 93D1, indicating that the passenger side
pretensioner seat belt resistance is too low, the resistance is lower than 1.2 ohm.
(18) The passenger side pretensioner seat belt resistance is short to ground (DTC 93D2)
When using the scan tool to test the airbag ECU, the DTC is 93D2, indicating that the passenger side
pretensioner seat belt is short to ground, the resistance is lower than 6.5K ohm.
(19) The passenger side pretensioner seat belt resistance is short to power supply (DTC 93D3)
When using the scan tool to test the airbag ECU, the DTC is 93D3, indicating that the passenger side
pretensioner seat belt is short to power supply, the resistance is lower than 21K ohm.
(20) Airbag ECU warning light is short to ground or warning light wire harness is disconnected (DTC 93D4)
When using the scan tool to test the airbag ECU, the DTC is 93D4, indicating that the airbag ECU warning light
is short to ground or the warning light wire harness is disconnected.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93D5? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Check the LED and wire harness for connection. Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the airbag ECU wire harness
connection is ok? (is there any short)
Check the connector of the warning light on airbag ECU wire harness (is
there any short)?
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93D4? Go to step 2 other
2 Go to step 3 Go to step 5
3 Go to step 4 Go to step 5
4 Check the LED and wire harness for connection. Go to step 5
5 Go to step 6 Go to step 1
6 The fault has been removed, use the scan tool to eliminate the DTC.Shut off the power supply, check whether the airbag ECU wire harness
connection is ok? (is there any short)Check the connector of the warning light on airbag ECU wire harness (is there any short)?After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check).SRS (Supplemental Restraint System)-SRS-General Information

5-62 (22) There are problems in the configuration of the airbag ECU (DTC 93D6)
When using the scan tool to test the airbag ECU, the DTC is 93D6, indicating that there are problems in the
configuration of the airbag ECU.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93D6? Go to step 2 other
2Go to step 3
3 Go to step 4 Go to step 1
4 The fault has been removed, use the scan tool to eliminate the DTC.Check whether the configuration of the airbag ECU is consistent with the
actual on-board configuration?
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check). (23) The impact signal output interface of the airbag ECU is short to ground or the impact output circuit is
disconnected. (DTC 93D7)
When using the scan tool to test the airbag ECU, the DTC is 93D7, indicating that the impact signal output
interface of the airbag ECU is short to ground or the impact output circuit is disconnected.IV. Diagnosis of collided vehicle No matter airbag is unfolded or folded, inspection and maintenance of collided vehicle should be performed
according to the following sequence.
1. Check ECU diagnosis signal.
(1) Connect scanner diagnosis joint
(2) Use scanner to read out diagnosis result.
2. Repair sequence
(1) when airbag is unfolded.
The following components should be replaced with new parts
a. Airbag assembly on passenger side
b. ECU
c. Airbag assembly on driver side
d. Seat belt with pretensionerNote:
due to impact, when battery power is insufficient, scanner can not communicate with ECU, now check and
service instrument board wire harness or use external power supply.SRS (Supplemental Restraint System)-SRS-General Information (2 ) Check the following components, if there is any abnormity, replace with new parts
a. Clock spring.
b. Steering wheel, steering column, lower steering shaft assembly
(3 ) The installation status of driver airbag assembly in relation to steering wheel
a. Check and see if there is abnormal noise in the steering wheel, the action of the same is good, or the
clearance is normal.
b. Check the connecter of the wire harness for damage and the terminal for distortion.

5-633. ECU
(1) Check the brackets of the ECU Case for recess, crack,
distortion, etc.
(2) Check the union joint for damage and terminal for distortion.
(3) Check the installation status of he ECU brackets
(4) Check the installation status of the airbag assembly.Notice
1. Work must be started 60s after the negative (-) terminal cable is disconnected from battery. The disconnected
negative (-) terminal cable shall be protected with insulating tape for insulation.
2. Airbag assembly and clock spring shall not be removed or repaired. They shall be replaced if there is any
trouble.
3. Pay enough attention to airbag assembly and clock spring when using,avoiding dropping them onto the
ground or into water or oil. In addition,if there is any pitting,crack or distortion on them,replace with new ones.
4. When an airbag is deployed, the deployed surface should face up. It should be kept on a flat surface without
any other items on it.
5. Don't keep an airbag in a place where the temperature is higher than 85°C.
6. When an airbag is deployed, it shall be replaced with a new one; simultaneously, check the clock spring,
and replace it with a new one if found abnormal.
7. When deal with the deployed airbag, gloves and protective glasses are to be used.
8. When scrapping the undeployed airbag, it shall be discarded after being deployed.Bracket Gas generatorDAB ConnectorHorn ConnectorSRS (Supplemental Restraint System)-SRS-General Information4. Driver airbag assembly (see the figure right above)
5. Clock spring (see the figure on the right)
(1) Check the connector and protecting tube for damage and the
terminal for distortion.
(2) Check the case for distortion.