ABS GEELY MK 2008 Service Manual

Rear Suspension System-LH/RH Rear Suspension Coil Spring4-5918. Mount rear right brake tube
Tips:
Mount the right assembly by using same operations as left.
19. Mount sideslip control sensor wire (with ABS)
(1) Tighten sideslip control sensor wire by bolts
Torque: 8.0 N.m
(2) Mount sideslip control sensor wire
Attention: Mount the right wire by using same operations as left.
20. Mount load-sensing valve bracket (without ABS)
Mount load-sensing valve bracket by two buts
21. Sufficiently tighten the rear axle frame assembly
(1) Stabilize the shock absorber assembly
Use the lifting jack and add 90Kg force on rear luggage
carrier if bolts can not be tightened at this point.
(2) Sufficiently tighten bolts
Torque: 82 N.m
22. Sufficiently tighten the left rear shock absorber assembly
Sufficiently tighten nuts
Torque: 49 N.m
23. Sufficiently tighten the right rear shock absorber assembly
Tips: Mount the right rear shock absorber by using same opera-
tions as left.
24. Release the air in the brake hose
25. Mount the rear wheel
Torque: 103 N.m
26. Check rear the wheel alignment
27. Check the wheel speed sensor signal of ABS( with ABS)

Section 4 Rear Absorber Installation AssemblyComponent ViewReplacement1. Remove the rear seat cushion assembly
2. Remove divided rear seat back assembly
3. Remove LH & RH rear seat back hinge (2 pieces)
4. Remove rear seat belt assembly
5. Remove left rear door moldingUpper suspension carrier
Rear vibration cushion
Shock absorber upper cover WasherLeft rear shock absorber assemblyRear Suspension System-Rear Absorber Installation Assembly4-60specified torqueN.
m :washer

Rear Suspension System-Rear Absorber Installation Assembly4-616. Remove rear left lower pillar interior panel
7. Remove the lower rear shelf interior panel
8. Remove rear left upper pillar interior pane
9. Remove rear right lower pillar interior pane
10. Remove the high brake lamp
11. Remove the rear shelf interior panel
12. Remove rear wheel
13. Remove the rear left shock absorber assembly
(1)Lift the rear axle frame by lifting jack (see right figure)
(2)Remove two nuts by clamping the piston push rod
(3)move the washer and upper suspension bracket
(4) Remove nut, washer and left rear shock absorber assembly
(5) Remove shock absorber upper cover
14. Check rear left shock absorber assembly
Check the abnormal resistance and noise in the operation by
compressing and extending the push rod, replace it if any abnormal.
15.Mount rear left shock absorber assembly
(1) Mount shock absorber upper cover
(2) Mount shock absorber, upper suspension bracket and washer
onto vehicle body
(3) After clamp piston push rod, mount lower nut and let piston
push rod higher 15-18mm than nut (see right figure)
(4) Mount upper nut according lower nut
Torque: 25N.m
(5) Mount shock absorber onto rear axle frame by washer and nut
at lifting jack
Torque: 49N.m
16. Mount rear wheel
Torque: 103N.m
17. Check rear wheel alignment

Section 5 Rear Suspension CrossmemberComponent ViewRear shock absorber subassembly
Upper washer
Left rear helical spring
Lower washer
Rear right support bushingLower washer Right rear helical springUpper washer
Rear suspension
crossmentber
Rear left support bushing
Parking brake cable assembly Load-sensing valve bracket without
ABSRear Suspension System-Rear Suspension Crossmember4-62specified torqueN.
m :Wheel speed sensor wire
Bracket with ABS
Brake hose
Rear brake drum
subassembly
Right rear hub and
bearing subassembly
Rear brake drum
subassembly Rear brake assembly Brake hose
Left rear hub&bearing
subassembly Clamp
Rear stabilizer
bar bushing
Non-reusable parts

Rear Suspension System-Rear Suspension Crossmember4-63Disassemble:1. Remove rear wheel
2. Remove sideslip control sensor wire (with ABS)
3. Remove load-sensing valve bracket (without ABS)
4. Remove proportioning valve and right rear brake tube
5. Remove proportioning valve and left rear brake tube
6. Remove right parking brake cable assembly
7. Remove left parking brake cable assembly
Tips: Remove right parts by using same operations as left
8. Remove rear brake drum subassembly
9. Remove left rear hub and bearing assembly
(1) Remove nuts and right parking brake cable assembly from
rear axle frame
(2) Remove four bolts and left rear hub and bearing assembly
(3) Remove rear brake assembly from rear axle frame
10. Remove rear right hub and bearing assembly
Tips: Remove right parts by using same operations as left
11. Loosen rear axle frame assembly
12. Disassemble rear left shock absorber assembly
13. Disassemble rear right shock absorber assembly
Tips: Remove right parts by using same operations as left
14. Remove rear left helical spring
15. Remove rear right helical spring
Tips: Remove right parts by using same operations as left
16. Remove rear axle assembly
(1) Lift rear axle assembly by lifting axel
(2) Remove two bolts and rear axle frame assembly

4-6523. Temporarily fasten the rear axle frame assembly
(1) Lift rear axle frame by lifting jack
(2) Mount the rear axle frame by temporarily tightening two bolts
24. Mount rear left helical spring
25. Mount rear right helical spring
Tips:
Mount right parts by using same operations as left
26. Temporarily tighten rear left shock absorber assembly
27. Temporarily tighten rear right shock absorber assembly
Tips:
Mount right parts by using same operations as left
28. Mount rear left hub and bearing assembly
Mount rear brake assembly, rear left hub and bearing assembly by
four bolts
29. Mount rear right hub and bearing assembly
Tips: Mount right parts by using same operations as left
30. Mount rear brake drum subassembly
31. Adjust the gap between brake drum and brake shoe
32. Mount #3 parking brake cable assembly
Tips: Mount right parts by using same operations as left
33. Mount #2 parking brake cable assembly
34. Mount #4 rear brake tube
35. Mount #3 rear brake tube
Tips: Mount right parts by using same operations as left
36. Connect sideslip control sensor wire(with ABS)
37. Connect load-sensing valve braket(without ABS)
38. Sufficiently tighten rear axle frame assembly
39. Sufficiently tighten rear left shock absorber assembly
40. Sufficiently tighten rear right shock absorber assembly
Tips: Mount right parts by using same operations as left
41. Release air from brake tube
42. Mount rear wheel
Torque: 103N.m
43. Check rear wheel alignment
44. Check the speed signal of ABS sensor( with ABS).Rear Suspension System
-Rear Suspension Crossmember

Component ViewSection 4 Brake Master Cylinder AssemblyVacuum boosterBrake System -Brake Master Cylinder Assembly4-85Brake master cylinder
sub-assembly
Vacuum tube
Fluid level indicator lamp connector Manual Transmission
#1 clutch fluidr tank pipe No ABS
specified torqueN.
m :

Component ViewBrake System -Brake Master Cylinder Assembly4-86With ABS:
Cover
Brake fluid reservoir
Strainer
Automatic Transmission
O-ring
Retaining ring
Pin
Straight pinPiston guide
block
Cup
Washer
#1 piston & Spring
#2 piston
Spring Hole connectorHole
connector
Master cylinder
Without ABS
Cover
Strainer
PinManual Transmission
O-ring
Retaining ring
Hole connector
Piston guide block
Cup
#1 piston & Spring
#2 piston & Spring
Washer
Piston limit bolt Master cylinder Hole connectorSpecified torque
Non-reusable parts
Lithium soap base glycol lube

Repair1. Discharge the brake fluid.
Note: Never spray the brake fluid on the paint surface, otherwise
wash it immediately.
2. Remove the brake master cylinder.
(1) Pull out the connector of the level alarm light switch.
(2) Slide the clip, and pull out #1 clutch storage tank pipe (manual
transaxle).
(3) Remove the two brake pipes from the brake master cylinder
with special tool.(with ABS)
(4) Remove the three brake pipes from the brake master cylinder
accessory with special tool. (without ABS)
(5) Remove the two lock nuts, and pull out the brake master
pump.
3. Remove the storage tank.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the pin from the brake master cylinder body with
punch and hammer.
(3) Pull out the Brake fluid reservoir.
(4) Remove the cover and strainer from the storage tank.
(5) Remove the storage tank and the two hole connectors.
4. Remove the brake master cylinder.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the O-ring.
(3) Push the piston with hand, and remove the snap ring with
snap ring pliers.Brake System -Brake Master Cylinder Assembly4-87With ABS:
Without ABS

(4) Push the piston with hand, and turn the cylinder body to
remove the straight pin. (with ABS)
(5) Push the piston with hand, and remove the piston bolt and
washer. (without ABS)
(6) Pull out #1 piston, piston guide block, spring, cup and washer
straightly.
Note: If angle appears in the pulling process, it may cause
damage to the cylinder wall.
(7) Put two blocks and cloth on the workbench. Put the flange of
the master cylinder against the block edge and knock it till #2
piston and spring get out of the cylinder.
Tips:Brake System -Brake Master Cylinder Assembly4-88 Make sure the distance (A) between the working cloth and the block's top is at least 100mm.
Note:
If angle appears in the pulling process, it may cause damage to the cylinder wall.
5. Check the brake master cylinder.
(1) Check the cylinder wall whether there is any rust or nick.
(2) Check the cylinder wall whether there is any abrasion or damage.
Note:
If necessary, clean or replace the brake master cylinder.
Tips:
Clean the assembled parts with compressed air.
6. Install the brake master cylinder.
(1) Fix the brake master cylinder on the bench clamp.
(2) Apply the lithium soap-base glycol lube on the rubber parts with arrow.
(3) Install # 2 and # 1 pistons, spring, piston guide block, cup and washer.
Note:
If angle appears in the installation process, it may cause damage to the cylinder wall. Be careful not to
damage the edge of the cup on the piston.