differential HONDA INTEGRA 1998 4.G User Guide

18. Install the sub-shaft assembly in the transmission
housing {see page 14-142],.
'19. Install the reverse idler gear and gear shaft holder(see page 14-158).
20. Install the differential assembly in the torque con
verter housrng.
21. Assemble the mainshaft and countershaft sub-
assembly, then install them together in the torque
converler noustng.
22. Turn the shilt fork so the large chamlered hole is fac-
ing the fork bolt hole, then installthe shift tork with
the reverse selector and torque the lock bolt. Bend
the lock tab against the bolt head.
SHIFT FORK
23. Install the reverse gear with the collar and needte
bearing on the countershaft.
24. Align the spring pin of the control shaft with the
transmission housing groove by turning the control
shaft.
25. Place the transmission housing on the torque con-
verter housing with a new gasket and the three
dowel pins.
CONTROL
TRANSMISSION HOUSING
lnstall the transmission housing mounting bolts along
with the transmission hanger and the connector
bracket, then torque the bolts in two or more steps
in the sequence shown.
TOROUE: rt4 N'm (4.5 kgt.m, 33 lbt.lt)
TRANSMISSION
26.
LOCK WASHERReplace.
6 x 1.0 mm4 t{.m(1.4 kgf.m, 10
e
Large chamfered hole
/ -'K\,,
a
14-163

Transmission
Installation (cont'd)
to.
'14. Install new set rings on the end ol the intermediate
shaft and the driveshaft.
'15. lnstall the intermediate shaft.
SET RINGBeplace.
10 x 139 N.m14.0 kgf.m, 29 lbf.ft)
Install exhaust pipe A, and connect the primary
heated oxygen sensor (HO2S) connector.
g
ISELF-LOCKING NUT10 x 1.25 mm54 N.m (5.5 kgf.m,40 tbf.frlReplace.
GASKETReplace.
SELF,LOCKING NUTS8 x 1.25 mm22 N.m {2.2 kgf.m,16 tbt.tt)Replace.
SELF-LOCKING NUTS8 x 1.25 mm16 N'm 11.6 kgf.m,12 tbf.ft)Replace.
SHAFT
14-170
6 x 10 mm BOLT
cllPs,5
1 7. Install the right and lelt drivershafts (see section '16).
NOTE: Turn the right and le{t steering knuckle fully
outward, and slide the right driveshaft into the
differential until you leel its spring clip engage the
side gear. Slide the left driveshaft into the intermedi
ate shaft until you feel the spring clip of the inter
mediate shaft engage the driveshaft.
'18. Install right damper fork, then insrall the right and
lett ball joints to each lower arm with the castle nuts
and new cotter prns.
\
COTTERReplace.CASTLE NUT12 x 1.25 mm49-59 N.m15.0- 6.0 kgf.m,36-43 lbl.tt)
19. lnstall the splash shield.
DAMPEB PINCH EOLT10 x 1.25 mm43 N.m {4.4 kgf .m, l.32 lb{.tr} - '- i
:'g
SELF-LOCKING NUT12 x 1.25 mm64 N.m {6.5 kgf.m,47 lbt.ftlReplace.
PIN
SHIELD

)
Differential
Manual Transmission
81881 engine ...................................... 15-1
818C1 engine ...................................... 15-9
818C5 engine .....,........... 15-19
Automatic Transmission .................. ..... 15-27

Differential (818B1 engine)
Special Tools ........ ........ 15-2
Differential
lllustrated Index......... . 15-3
Backfash Inspection .... 15-4
Final Driven Gear Replacement ...... 15-4
Bearing Replacement .................... 1 5-5
Oil Seal Removal ........ 15-5
Side Clearance Adjustment ........... 15-6
Oil Seal Installation .-... 15-8
t

Differential (81 881 engine)
lllustrated Index
t
OIL SEAL Replace.Removal, page 15-5Installation, page 15-8
FINAL DRIVEN GEARInspect for wear and damage,Replacement, page 15-4
DIFFEBENTIAL CARRIERInspection, page 15-4
BALL BEARINGInspect for wear and operation.Replacement, page 15 5
BALL BEARINGInspect for wear and operation.Replacement, page 15-5
10 x 1.0 mm101 N'm 110.3 kgt.m, 74.5 lbt'tt)Lefahand threads
80 mm SHIMSelection, page 15 6
Removal, page 15-5Insrallation, page 1 5-8
15-3

Differential (81881 engine)
Backlash Inspection
Place differential assembly on V-blocks and install
both axles.
N4easure the backlash ot both pinion gears
Standa.d (Newl: O.O5-0.15 mm (O.OO2-0.006 in)
3. It the backlash is not within the standard, replace
the differential carrier.
Final Driven Gear RePlacement
1. Remove the bolts in a crisscross pattern ln several
steps, then remove the linal driven gear trom the
differential carrier.
NOTE: The final driven gear bolts have left-hand
tnreaos.
10 x 1.0 mm101 N'm 110.3 kgf'm, 74.5 lbf'fll
Left-hand threads
FINAL DRIVEN GEAR
OIFFERENTIALCARRIER
Install the final driven gear by tightening the bolts
in a crissc.oss pattern in several steps.
OIAL INDICATOR
Charnfer on inside diameter ottinal driven gear faces carrier.
\
15-4

Bearing Replacement
t
a
NOTE: Check the ball bearings for wear and rough ro-
tation. lf bearings are OK, removal is not necessary.
'1. Remove the ball bearings using a standard bearing
puller and bearing separator as shown.
BEARING PULLER(Commercially
available)
BALL BEARING
2.lnstall new ball bearings using the special tool as
shown.
NOTE: Drive the bearings squarely until they bot-
tom against the carrier.
DRIVER, 40 mm l.D.07746-00301OO
BALL BEARING
't.
2.
Remove the differential assembly.
Remove the 80 mm shim from the transmission
housrng.
80 mm SHIM
TRANSMISSIONHOUSING
3. Remove the oil seal from the transmission housinq.
4. Remove the oil seal from the clutch housinq.
OIL SEALReplace.
SealRemoval
1s-5

Differential (81 8BJ engine)
Side Clearance Adjustment
1. lnstall the dilferential assembly, making sure at bot-
toms in the clutch housing, using the special tool as
shown.
DRIVER, 40 mm I D.o7746-0030100
HOUSING
2. Install the 80 mm shim.
NOTE: Insrall the 80 mm shim that was removed.
mm SHIM
15-6
3.Install the transmission housing (see section 13).
NOTE: Do not apply liquid gasket to the mating sur-
face of the clutch housing.
Tighten the transmission housing attaching bolts
{see section l3}.
8 x 1.25 mm
27 N.m {2.8 kgf.m. 20 lbf'ft}
Use the special tool to bottom the differential assem-
bly in the clutch housing.
Measure clearance between the 80 mm shim and
bearing outer race in the transmission housing.
5.
6.

Differential (81881 engine)
Oil Seal Installation
1. lnstall the oil seal into the transmission housing us-
ing the special tools as shown
DRIVER07749-0010000
OIL SEALReplace.
HOUSING
15-8
Install the oil seal into the clutch housing using the
special tools as shown.
ORIVER07749-OO10000
OIL SEALReplace.

Differential (818C1 engine)
Special Tools ........ ........ 15-10
Differential
lllustrated Index......... . 15-11
Backfash Inspection .,.. 15-12
Finaf Driven Gear Replacement ...... 15-12
Tapered Roller Bearing Replacement. 15-13
Oil Seal Removal ........ 15-13
Bearing Outer Race Replacement ... 15-14
Tapered Roller Bearing Preload
Adjustment ............. 15-15
Oif Seaf Installation ..... 15-17