Hyundai Equus 2016 Owner's Manual
Page 411 of 477
7-54
Maintenance
Vehicle Capacity Weight: The mul-
tiplication of the designated occu-
pant seat number by 150 pounds (68
kg) plus the loading weight.
Vehicle Maximum Load on the
Tire: Loading capacity for an individ-
ual tire. The curb and accessory
weights plus the maximum occupant
and loading weights.
Vehicle Normal Load on the Tire:
Loading capacity for an individual
axle. The sum of the curb, accessory,
and normal occupant weights is
divided by 2.
Vehicle Placard: A label, perma-
nently attached to a vehicle, to indi-
cate the original equipment tire size
and the recommended inflation pres-
sure.
All season tires
HYUNDAI designated some models
of all-season tires to provide good
performance for use all year round,
including snowy and icy road condi-
tions. All-season tires are identified
by ALL SEASON and/or M+S (Mud
and Snow) on the tire side wall.
Snow tires have better snow traction
than all season tires and may be
more appropriate in some areas.
Summer tires
HYUNDAI designated some models
of summer tires to provide superior
performance on dry roads. Summer
tire performance is substantially
reduced in snow and ice. Summer
tires do not have a tire traction rating
mark, M+S (Mud and Snow), on the
tire side wall. Before driving in snowy
or icy conditions, it is recommended
to install snow tires or all-season
tires on all four wheels.
Snow tires
When equipping your vehicle with
snow tires, the tires should be in the
same size and have the same load
capacity as the original ones. Snow
tires should be installed on all four
wheels. Otherwise, it may cause
poor handling. Snow tires should be
more inflated by 4 psi (28 kPa) than
the lesser of the two recommended
pressures - one specified on the tire
label attached to the central pillar on
the driver's side, and the other spec-
ified on the tire side wall.
Do not drive faster than 75 mph (120
km/h) when your car is equipped with
snow tires.
- Snow or ice
When driving on a snowy or icy road, drive slower than 20
mph (30 km/h).
Use the SAE “S” class or wire chains.
When you hear chain-rattling noise, retighten the chain to
avoid its contact with the
vehicle body.
To prevent damage to the vehicle body, retighten the
chains after driving 0.3~0.6
miles (0.5~1.0 km).
Do not use tire chains on a vehicle equipped with alu-
minum wheels. In unavoidable
circumstance, use the wire-
type chains.
Use the wire chains, of which the diameter is less than 0.47
inches (12 mm), to prevent
damage to the chain connect-
ing parts.
WARNING
Page 412 of 477
7-55
Maintenance07
Tire chains
Tire chains, if necessary, should be
installed on the drive wheels (rear
wheels).
Make sure that the chains are
installed in accordance with the man-
ufacturer's instructions.
To minimize the abrasion of tires and
chains, do not use the chains, when
unnecessary.
Radial-ply tires
Radial-ply tires provide longer tread
life, better road hazard resistance
and smoother riding at a high speed.
The radial-ply tires used on this vehi-
cle are of belted construction, and
are to improve your driving and han-
dling. Radial-ply tires have the same
loading capacity as the bias-ply or
bias-belted tires of the same size.
Inflate the radial-ply tires to the same
recommended inflation pressure. It is
not recommended to attempt a
cross-combination of radial-ply tires
and bias-ply(or bias-belted) tires on
the same vehicle. Any cross-combi-
nation of radial-ply and bias-ply(or
bias-belted) tires on one vehicle will
seriously deteriorate vehicle han-
dling. The best rule to follow is:
Identical radial-ply tires should
always be used for a set of four tires.
A tire, which is driven for a long peri-
od of time, is more susceptible to
irregular tread abrasion. It is very
important to rotate tires, at the inter-
val instructed in this chapter, to use it
up to its potential tread life. Any cut
and puncture on a radial-ply tire is
repairable, only when it is on the
tread, because of the side wall flex-
ing. Consult your tire dealer for a
radial-ply tire repair.
Page 413 of 477
7-56
Maintenance
A vehicle’s electrical system is pro-
tected from a possible electrical
overloading damage by fuses.
This vehicle has 4 fuse panels - two
on the driver’s side, another on the
panel bolster of the passenger's
side, and the other in the engine
compartment.
When any of your lights, acces-
sories, or controls does not operate,
check the appropriate circuit fuse.
When a fuse is out, some elements
may melt inside.
When the electrical system does not
operate, check the fuse panel on the
driver's side first.
Before replacing the fuse, disconnect
the negative battery cable. Always
replace it with a fuse of the same rat-
ing. When the newly-replaced fuse
blows, there may be an electrical
problem. Avoid using any pertinent
systems. Immediately consult an
authorized EQUUS dealer.
Three kinds of fuses are to be used:
a blade type for lower amperage rat-ing, and a cartridge type and a fusiblelink for higher amperage ratings.
Information
The actual fuse, relay panels, and
labels may differ from the equipped
items.
i
F F U
U S
SE
E S
S
OVI075172N
Normal
Normal
Blade type
Cartridge type
Fusible link Blown
Blown
Normal Blown
- Fuse replacement
Never replace a fuse with the
one of a different rating.
A higher capacity fuse may cause damage or a fire.
Never use a wire or an alu- minum foil, instead of a prop-
er fuse - even as an emergent
measure. It may damage
extensive wirings and cause a
fire.
WARNING
Do not use a screwdriver or any
other metal object to remove a
fuse. It may cause a short cir-
cuit and damage the system.
CAUTION
Page 414 of 477
7-57
Maintenance07
When replacing a blown fuse orrelay with a new one, make sure
the new fuse or relay fits tightly
into the clips The incomplete
fastening fuse or relay may
cause the vehicle wiring and
electric systems damage and a
possible fire.
Do not remove fuses, relays and terminals fastened with bolts or
nuts. The fuses, relays and ter-
minals may be fastened incom-
pletely, and it may cause a pos-
sible fire. If fuses, relays and ter-
minals fastened with bolts or
nuts are blown, consult an
authorized EQUUS dealer.
Do not input any other objects except fuses or relays into
fuse/relay terminals such as a
driver or wiring. It may cause
contact failure and system mal-
function.
Inner panel fuse replacement
1. Turn OFF the ignition switch and all the other switches.
2. Open the fuse panel cover.
NOTICE
OVI075100N
Driver’s side
OVI075173N
Front passenger’s side
Page 415 of 477
7-58
Maintenance
3.Pull straight out a fuse, which is suspected to be out. Use the fuse
puller provided in the panels either
on the driver’s side or the front pas-
senger’s side.
4. Check the removed fuse. When the fuse is out, replace it.
Spare fuses are provided in the
fuse panels in the front passen-
ger's side. (or in the fuse panel of
the engine compartment)
5. Install a new fuse of the same rat- ing, and tightly secure it in the
clips.
When it is loosely fit, consult an
authorized EQUUS dealer.
When you do not have a spare fuse,
use a fuse of the same rating from a
circuit, such as a cigarette lighter fuse,
which may not be needed to drive. When the headlamps or other electri-
cal components do not operate, but
when the fuses are not blown out,
check the fuse panel in the engine
compartment. In case that a fuse is
blown out, it must be replaced.fuse is
blown, it must be replaced.
Fuse switch
Always set the transportation fuse
switch in the "ON" position. When
you press it OFF, some devices,
such as the audio and the digital
clock, must be reset. Also, the Smart
Key may not properly operate.
Always set the transportation
fuse switch in the "ON" position
while driving.
Do not repeatedly press the transportation fuse switch. The
fuse switch may be worn out.
Information
When you do not drive your vehicle
more than 1 month, press OFF the
transportation fuse switch to prevent
a battery discharge.
i
NOTICE
OVI075101N
Driver’s side
OVI075174N
Front passenger’s side
OVI075102N
Page 416 of 477
7-59
Maintenance07
Engine compartment fuse
replacement
1. Turn OFF the ignition switch andall the other switches.
2. Open the fuse panel cover by pressing the tab.
3. Check the removed fuse. When the fuse is out, replace it. To
remove or insert the fuse, use the
fuse puller in the panel on the front
passenger’s side.
4. Install a new fuse of the same rat- ing, and tightly secure it in the
clips. When it is loosely fit, consult
an authorized EQUUS dealer. After checking the fuse panel in
the engine compartment, securely
close the fuse panel cover. If not,
electrical failures may occur due
to a possible water contact.
Main fuse
When the main fuse is out, it must be
removed in the following procedure:
1. Open the fuse panel cover on the
right side of the engine compart-
ment.
2. Loosen the nuts, as shown in the above illustration.
3. Use a new fuse of the same rating.
4. Install the new fuse in the reverse order.
Information
When the main fuse is blown out, con-
sult an authorized EQUUS dealer.
i
NOTICE
OVI075175N
OVI075176N
OVI075177N
Page 417 of 477
7-60
Maintenance
Instrument panel fuse panel Engine compartment fuse panel
OVI075105N
Driver’s side
OVI075178N
Front passenger’s side
OVI075104N
OVI075103N
Fuse/relay panel description
Under the fuse/relay panel covers, the fuse/relay labels are attached for infor-
mation, such as fuse/relay name and capacity.
Information
Some fuse-panel information in this manual may be inapplicable to your vehicle.
Information in this manual reflects only the current information at the point of
printing. Refer to the fuse label, when inspecting the fuse panel.
i
Page 418 of 477
7-61
Maintenance07
OVI073108N
Driver’s side instrument fuse panel
Page 419 of 477
7-62
Maintenance
Instrument panel (Driver’s side fuse panel)
Fuse Name Fuse ratingCircuit Protected
PDM (B+) 25A Smart Key Control Module
HAZARD 10A Center Facia Switch
EPB 10A Electric Parking Brake Switch, Crash Pad Switch
RF RECEIVER 10A RF Receiver, Security Indicator PDM (IG1) 10A Smart Key Control Module
SHIFT LEVER (IG1) 10A ATM Shift Lever IND. A/BAG IND. 10A Instrument Cluster
SMART KEY 10A Start/Stop Button Switch P/HANDLE 10A Steering Tilt & Telescopic Module
MEMORY 10APower Trunk Lid Control Module, Relax Module
Driver/Passenger Door Module, Rear Door Module
LH/RH, Passenger Door Lamp, Passenger Door Mood
Lamp, Rear Door Lamp LH/RH, Rear Door Mood Lamp
LH/RH Instrument Cluster, Driver IMS Control Module,
BCM, Analogue Clock, LCD Panel Switch,
A/C Control Module, Data Link Connector
TPMS 10A Tire Pressure Monitoring Module
ACTIVE H/REST 10A Active Head Rest Sensor Module CLUSTER 10A Instrument Cluster, Head-Up Display
STOP LAMP 10A Stop Lamp Switch, Smart Key Control Module
SHIFT LEVER (B+) 10A Sport Mode Switch
MULTI MEDIA 15A A/V & Navigation Head Unit, Front Monitor, Split Unit,
MTS Module, Front DIS Switch, Rear Monitor LH/RH,
Rear Console Switch, Rear Audio Switch
BCM 10A BCM
IG1 30AE/R Junction Box (Fuse - B/UP LAMP, ESC, EHPS,
AFLS, INJECTOR (IG1), CRUISE (IG1), ECU (IG1),
TCU)
1 MODULE 10A Head-Up Display, Rain Sensor, Rear Power Seat Switch LH
F/LID 10A Fuel Filler Door Switch, Front Console Switch
FOLD'G MIRR 10A Driver/Passenger Door Module
A/BAG 15ASRS Control Module, Driver/Passenger Pre-Safe Seat
Belt, Center Facia Switch, PODS Module
4 MODULE 10A E/R Junction Box (FAM), Multifunction Switch
Driver/Passenger Door Module
ECS 15A ECS Control Module
AUDIO (IG1) 10A A/V & Navigation Head Unit, MTS Module AFLS 10A Head Lamp LH/RH, Adaptive Front Lighting Module
O/S HDL DRV 15A Driver Power Door Latch, Driver Power Seat Switch,
Driver Door Lamp, Driver Door Mood Lamp, Driver Smart
Key Outside Handle
Page 420 of 477
7-63
Maintenance07
Fuse Name Fuse ratingCircuit Protected
S/HEATER RR 15A Rear CCS Control Module LH, Rear Seat Warmer
Module LH
2 MODULE 10A Power Trunk Lid Control Module, Electro Chromic Mirror,
A/T Console Switch
A/CON 10AA/C Control Module, AQS Sensor, Driver IMS Control
Module Relax Module, Driver/Passenger CCS Control
Module Driver/Passenger Seat Warmer Module,
Rear CCS Control, Module LH/RH, Rear Seat Warmer
Module LH/RH, Alternator Resistor (Alternator,
Instrument Cluster, USB Jack, Rear Console Switch)
O/S HDL RR 15A Rear Power Door Latch LH, Rear Door Window Curtain
LH, Rear Smart Key Outside Handle LH
3 MODULE 10A ECS Control Module, Front Console Switch, Crash Pad
Switch, Blind Spot Detection Radar LH/RH Tire Pressure
Monitoring Module, Stop Lamp Switch, Steering Tilt &
Telescopic Module, LDWS Camera Module Electric
Parking Brake Module, Front/Rear Parking Assist Sensor
LH/RH Front/Rear Parking Assist Sensor LH/RH (Center)
DR LOCK DRV 10A Driver Door Module
S/HEATER DRV 15A Driver CCS Control Module, Driver Seat Warmer Module
DR LOCK PASS 15A Passenger Door Module P/TRUNK 30A Power Trunk Lid Control Module
P/SEAT PASS 30A Relax Module
RH SAFETY
POWER WINDOW 30APassenger Power Window Module,
Rear Power Window Module RH
LH SAFETY
POWER WINDOW 30ADriver Power Window Module,
Rear Power Window Module LH