HYUNDAI PALISADE 2022 Owners Manual

5-87
Driving your vehicle
5
If you press Blind-Spot Safety but-ton while 'Warning only' is selected
the indicator on the button extin-
guishes and the system deacti-
vates.
If you press Blind-Spot Safety but- ton while the system is cancelled
the indicator on the button illumi-
nates and the function activates. In
this case, the function returns to
the state before the engine turned
off.
When the function is initially turned
on and when the engine is turned
off then on again while the function
is in activation, the warning light
will illuminate for 3 seconds on the
outside rearview mirror. When the engine is restarted with
the function off, the ‘Blind-Spot
Safety System is Off’ message will
appear on the cluster.
If you change the setting from ‘Off’ to
‘Warning Only’, the warning light on
the outside rearview mirror will blink
for three seconds.
In addition, if the engine is turned on,
when Blind-Spot Collision Warning is
set to ‘Warning Only’, the warning
light on the outside rearview mirror
will blink for three seconds.Information
If the engine is restarted, Blind-Spot
Safety system will maintain the last
setting.
i
OLX2059032LOTM070097N

If ‘Warning only’ is selected,
braking is not assisted.
If ‘Off’ is selected, the driver
should always be aware of the
surroundings and drive safe-
ly.
WARNING

5-88
Driving your vehicle
Warning Timing
With the engine on, select ‘Driver
assistance →Warning timing’ from
the Settings menu to change the ini-
tial warning activation time for Blind-
Spot Safety system.
When the vehicle is first delivered,
Warning Timing is set to ‘Normal’. If
you change the Warning Timing, the
warning time of other Driver
Assistance systems may change.
Warning Volume
With the engine on, select 'Driver
Assistance →
Warning Volume' from
the Settings menu to change the
Warning Volume to 'High', 'Medium',
'Low' or 'Off' for Blind –Spot Collision
Warning.
However, even if 'Off' is selected,
Blind-Spot Collision Warning's
Warning Volume will not turn off but
the volume will sound as 'Low'.
If you change the warning volume,
the Warning Volume of other Driver
Assistance systems may change.
OTMA058089
The setting of the Warning
Timing and Warning Volume
applies to all functions of the
Blind-Spot Safety system.
Even though ‘Normal’ is
selected for Warning Timing, if
the vehicles approaches at
high speed, the initial warning
activation time may seem late.
Select ‘Later’ for Warning
Timing when traffic is light
and when driving speed is
slow.
CAUTION
ONX4E070090

5-89
Driving your vehicle
5
Blind-Spot Collision Warning
operation
Warning and control
Vehicle detection
To warn the driver a vehicle isdetected, the warning light on the
outside rearview mirror and head-
up display (if equipped) will illumi-
nate.
Blind-Spot Collision Warning will operate when your vehicle speed
is above 20 mph (30 km/h) and the
speed of the vehicle in the blind
spot area is above 7 mph (10
km/h).
Collision warning
Collision warning will operate whenthe turn signal is turned on in the
direction of the detected vehicle.
To warn the driver of a collision, the warning light on the outside
rearview mirror and head-up dis-
play (if equipped) will blink. At the
same time, an audible warning will
sound.
When the turn signal is turned off or you move away from the lane,
the collision warning will be can-
celed and the function will return to
vehicle detection state.
Information
If the driver's seat is on the left side,
the collision warning may occur when
you turn left. Maintain a proper dis-
tance with the vehicles in the left lane.
If the driver's seat is on the right side,
the collision warning may occur when
you turn right. Maintain a proper dis-
tance with the vehicles in the right
lane.
i
ORG3070025
The detecting range of the
rear corner radar is deter-
mined by the standard road
width, therefore, on a narrow
road, the function may detect
other vehicles in the next next
lane and warn you. In con-
trast, on a wide road, the func-
tion may not be able to detect
a vehicle driving in the next
lane and may not warn you.
When the hazard warning
light is on, the collision warn-
ing by the turn signal will not
operate.
WARNING

5-90
Driving your vehicle
Blind-Spot Collision Warning
malfunction and limitations
Blind-Spot Collision Warningmalfunction
When Blind-Spot Collision Warning
is not working properly, the ‘Check
Blind-Spot Safety system’ warning
message will appear on the cluster,
and the Blind-Spot Collision Warning
turn off automatically, or the function
will be limited. We recommend that
Blind-Spot Collision Warning be
inspected by an authorized
HYUNDAI dealer.
OTM070099N
Take the following precautions
when using Blind-Spot Safety
system:
For your safety, change the
Settings after parking the
vehicle at a safe location.
If any other system’s warning
message is displayed or audi-
ble warning is generated,
Blind-Spot Safety system’s
warning message may not be
displayed and audible warn-
ing may not be generated.
You may not hear the warning
sound of Blind-Spot Safety
system if the surrounding is
noisy.
Blind-Spot Safety system may
warn the driver late or may not
warn the driver depending on
the road and driving condi-
tions.
Driver should maintain con-
trol of the vehicle at all times.
Do not depend on Blind-Spot
Safety system. Maintain a safe
braking distance, and if nec-
essary, depress the brake
pedal to reduce driving speed
or to stop the vehicle.WARNING

5-91
Driving your vehicle
5
When the outside rearview mirror
warning light is not working properly,
the ‘Check side view mirror warning
light’ warning message will appear
on the cluster. Have the vehicle
inspected by an authorized
HYUNDAI dealer.
Blind-Spot Collision Warningdisabled
When the rear bumper around the
rear corner radar or sensor is cov-
ered with foreign material, such as
snow or rain, or installing a trailer or
carrier, it can reduce the detecting
performance and temporarily limit or
disable Blind-Spot Safety system.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’
warning message will appear on the
cluster.
Blind-Spot Collision Warning will
operate normally when such foreign
material or trailer, etc. is removed,
and then the engine is restarted. If the function does not operate nor-
mally after it is removed, have the
vehicle inspected by an authorized
HYUNDAI dealer.
OTM070098N
OTM070100N

Even though the warning
message does not appear on
the cluster, Blind-Spot Safety
system may not properly
operate.
Blind-Spot Safety system may
not properly operate in an
area (e.g. open terrain), where
any substance are not detect-
ed right after the engine is
turned on, or when the detect-
ing sensor is blocked with for-
eign material right after the
engine is turned on.
WARNING
Turn off Blind-Spot Safety sys-
tem to install a trailer, carrier,
etc., or remove the trailer, carri-
er, etc. to use Blind-Spot Safety
system.
CAUTION

5-92
Driving your vehicle
Limitations of Blind-SpotCollision Warning
Blind-Spot Collision Warning may not
operate normally, or the function may
operate unexpectedly under the fol-
lowing circumstances:
There is inclement weather, such
as heavy snow, heavy rain, etc.
The rear corner radar is covered with snow, rain, dirt, etc.
The temperature around the rear corner radar is high or low
Driving on a highway (or motor- way) ramp
The road pavement (or the periph- eral ground) abnormally contains
metallic components (i.e. possibly
due to subway construction)
There is a fixed object near the vehicle, such as sound barriers,
guardrails, central dividers, entry
barriers, street lamps, signs, tun-
nels, walls, etc. (including double
structures)
Driving in large areas where there are few vehicles or structures (i.e.
desert, meadow, suburb, etc.) Driving through a narrow road
where trees or grass are over-
grown
Driving on a wet road surface, such as a puddle on the road
The other vehicle drives very close behind your vehicle, or the other
vehicle passes by your vehicle in
close proximity
The speed of the other vehicle is very fast that it passes by your
vehicle in a short time
Your vehicle passes by the other vehicle
Your vehicle changes lane
Your vehicle has started at the same time as the vehicle next to
you and has accelerated
The vehicle in the next lane moves two lanes away from you, or when
the vehicle two lanes away moves
to the next lane from you
A trailer or carrier is installed around the rear corner radar
The bumper around the rear cor- ner radar is covered with objects,
such as a bumper sticker, bumper
guard, bike rack, etc. The bumper around the rear cor-
ner radar is impacted, damaged or
the radar is out of position
Your vehicle height is low or high due to heavy loads, abnormal tire
pressure, etc.

5-93
Driving your vehicle
5
Blind-Spot Collision Warning may not
operate normally, or the function may
operate unexpectedly when the fol-
lowing objects are detected:
A motorcycle or bicycle is detected
A vehicle such as a flat trailer isdetected
A big vehicle such as a bus or truck is detected
A moving obstacle such as a pedestrian, animal, shopping cart
or a baby stroller is detected
A vehicle with low height such as a sports car is detected
For more details on the limita-
tions of the front view camera,
refer to “Forward Collision-
Avoidance Assist (FCA)” and
“Lane Keeping Assist (LKA)
section in chapter 5.
CAUTION
Driving on a curved road
Blind-Spot Collision Warning
may not operate properly
when driving on a curved
road. The function may not
detect the vehicle in the next
lane.
Always pay attention to road
and driving conditions while
driving.
Blind-Spot Collision Warning
may not operate properly
when driving on the curved
road. The function may recog-
nize the vehicle in the same
lane.
Always pay attention to road
and driving conditions while
driving.
WARNING
OJX1079057
OJX1079058

5-94
Driving your vehicle Driving where the road is
merging/dividing
Blind-Spot Collision Warning
may not operate properly
when driving where the road
merges or divides. The func-
tion may not detect the vehi-
cle in the next lane.
Always pay attention to road
and driving conditions while
driving.
Driving on an inclined road
Blind-Spot Collision Warning
may not operate properly
when driving on a slope. The
function may not detect the
vehicle in the next lane or may
incorrectly detect the ground
or structure.
Always pay attention to road
and driving conditions while
driving.Driving where the heights of
the lanes are different
Blind-Spot Collision Warning
may not operate properly
when driving where the
heights of the lanes are differ-
ent. The function may not
detect the vehicle on a road
with different lane heights
(underpass joining section,
grade separated intersec-
tions, etc.).
Always pay attention to road
and driving conditions while
driving.
OJX1079059
OLX2058040
OLX2058039

5-95
Driving your vehicle
5
Information
This device complies with Part 15 of
the FCC rules.
Operation is subject to the following
three conditions:
1. This device may not cause harmfulinterference, and
2. This device must accept any inter- ference received, including interfer-
ence that may cause undesired
operation.
3. Changes or modifications not expressly approved by the party
responsible for compliance could
void the user's authority to operate
the device.
Information
Radio frequency radiation exposure
information:
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed
and operated with minimum distance
of 8 in. (20 cm) between the radiator
(antenna) and your body.
This transmitter must not be co-locat-
ed or operating in conjunction with
any other antenna or transmitter.
ii
When you are towing a trailer
or another vehicle, make sure
that you turn off Blind-Spot
Collision Warning.
Blind-Spot Collision Warning
may not operate normally if
interfered by strong electro-
magnetic waves.
Blind-Spot Collision Warning
may not operate for 15 sec-
onds after the vehicle is start-
ed, or the rear corner radars
are initialized.
WARNING

5-96
Driving your vehicle
Blind-Spot Collision-Avoidance
Assist is designed to help detect and
monitor approaching vehicles in the
driver’s blind spot area and warn the
driver of a possible collision with a
warning message and audible warn-
ing.
In addition, if there is a risk of colli-
sion when changing lanes or driving
forward out of a parking space, the
function will help avoid collision by
applying the brake. Blind-Spot Collision-Avoidance
Assist helps detect and inform the
driver that a vehicle is in the blind
spot.Blind-Spot Collision Assist helps
detect and inform the driver that a
vehicle is approaching at high speed
from the blind spot area.
B B
L LI IN N D D- -S S P P O O T T C C O O L LL LI IS S I IO O N N- -A A V VO O I ID D A A N N C CE E A A S SS SI IS S T T ( ( B B C CA A ) ) ( ( I IF F E E Q Q U UI IP P P PE ED D ) )
OJX1079256OJX1079026
The detecting range may vary
depending on the speed of your
vehicle. However, even if there
is a vehicle in the blind spot, the
function may not warn you
when you pass by at high
speeds.
CAUTION
Warning timing may vary
depending on the speed of the
vehicle approaching at high
speed.
CAUTION