engine INFINITI QX56 2011 Factory Service Manual

TM-68
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000006226782
VALUES ON DIAGNOSIS TOOL
NOTE:
1. The CONSULT-III electrically displays shift timi
ng and lock-up timing (that is, operation timing of each
solenoid).
Check for time difference between actual shift timi ng and the CONSULT-III display. If the difference is
noticeable, mechanical parts (except solenoids, sens ors, etc.) may be malfunctioning. Check mechanical
parts in accordance with the specified diagnostic procedures.
2. Shift schedule (that implies gear position) on CONSULT-III may slightly differ from that is described in Ser-
vice Manual. This occurs because of the reasons as per the following:
- Actual shift schedule has more or less tolerance or allowance
- Shift schedule in Service Manual refers to the point where shifting starts
- Gear position on CONSULT-III indicates the point where shifting completes
3. Display of solenoid valves on CONSULT-III changes at t he start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
CONSULT-III MONITOR ITEM
Item name Condition Value / Status (Approx.)
VHCL/S SE-A/T During driving Approximately equals the speed-
ometer reading.
ESTM VSP SIG During driving Approximately equals the speed-
ometer reading.
OUTPUT REV During driving (lock-up ON) Tachometer / Gear ratio
INPUT SPEED During driving (lock-up ON) Approximately equals the engine
speed.
F SUN GR REV During driving Revolution of front sun gear is indi-
cated.
F CARR GR REV During driving Revolution of front carrier is indi-
cated.
ENGINE SPEED Eng ine running Closely equals the tachometer
reading.
TC SLIP SPEED During driving Engine speed − Input speed
ACCELE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
THROTTLE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
ATF TEMP 1 Ignition switch ON Temperature of ATF in the oil pan is
indicated.
ATF TEMP 2 Ignition switch ON Temperature of ATF at the exit of
torque converter.
AT F T E M P S E 1 0 °C (32 ° F) – 20 °C (68 °F) – 80 °C (176 °F) 3.3 – 2.7 – 0.9 V
BATTERY VOLT Ignition switch ON Battery voltage (11 V – 14 V)
LINE PRES SOL During driving 0.2 – 0.6 A
TCC SOLENOID Slip lock-up is active 0.2 – 0.8 A
Lock-up is active 0.8 A
Other than the above 0 A
L/B SOLENOID Low brake is engaged 0.6 – 0.8 A
Low brake is disengaged 0 – 0.05 A
Revision: 2010 May2011 QX56

TCM
TM-69
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
FR/B SOLENOID Front brake is engaged 0.6 – 0.8 A
Front brake is disengaged 0 – 0.05 A
HLR/C SOL High and low reverse clutch is disengaged 0.6 – 0.8 A
High and low reverse clutch is engaged 0 – 0.05 A
I/C SOLENOID Input clutch is disengaged 0.6 – 0.8 A
Input clutch is engaged 0 – 0.05 A
D/C SOLENOID Direct clutch is disengaged 0.6 – 0.8 A
Direct clutch is engaged 0 – 0.05 A
2346/B SOL 2346 brake is engaged 0.6 – 0.8 A
2346 brake is disengaged 0 – 0.05 A
L/P SOL MON During driving 0.2 – 0.6 A
TCC SOL MON Slip lock-up is active 0.2 – 0.8 A
Lock-up is active 0.8 A
Other than the above 0 A
L/B SOL MON Low brake is engaged 0.6 – 0.8 A
Low brake is disengaged 0 – 0.05 A
FR/B SOL MON Front brake is engaged 0.6 – 0.8 A
Front brake is disengaged 0 – 0.05 A
HLR/C SOL MON High and low reverse clutch is disengaged 0.6 – 0.8 A
High and low reverse clutch is engaged 0 – 0.05 A
I/C SOL MON Input clutch is disengaged 0.6 – 0.8 A
Input clutch is engaged 0 – 0.05 A
D/C SOL MON Direct clutch is disengaged 0.6 – 0.8 A
Direct clutch is engaged 0 – 0.05 A
2346/B SOL MON 2346 brake is engaged 0.6 – 0.8 A
2346 brake is disengaged 0 – 0.05 A
GEAR RATIO Driving with 1GR 4.887
Driving with 2GR 3.170
Driving with 3GR 2.027
Driving with 4GR 1.412
Driving with 5GR 1.000
Driving with 6GR 0.864
Driving with 7GR 0.775
ENGINE TORQUE During driving Changes the value according to
the acceleration or deceleration.
ENG TORQUE D During driving Changes the value according to
the acceleration or deceleration.
INPUT TRQ S During driving Changes the value according to
the acceleration or deceleration.
INPUT TRQ L/P During driving Changes the value according to
the acceleration or deceleration.
TRGT PRES L/P Selector lever in “P” an
d “N” positions 490 kPa
Other than the above 490 – 1370 kPa
TRGT PRES TCC Slip lock-up is active 0 – 600 kPa
Lock-up is active 600 kPa
Other than the above 0 kPa
Item name Condition Value / Status (Approx.)
Revision: 2010 May2011 QX56

TCM
TM-77
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
1ST ENGINE BRAKE PROTECTION CONTROL
Controls the engine brake so as not to make effective by turning the front brake solenoid output to OFF when
each solenoid becomes the electricity pattern of 1st engine brake during driving at the vehicle speed 25 km/h
or more in any positions other than “R” position and 1GR.
TCM HIGH TEMPERATURE PROTECTION CONTROL
Limit the accelerator opening and forcibly control the vehi cle to the low torque driving when the electronic sub-
strate in TCM reaches the high temperature.
DTC Inspection Priority ChartINFOID:0000000006226785
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the priority as per the
following list.
Malfunction detection condition Vehicle speed: 10 km/h (7 MPH) or more
Control at malfunction Neutral
Normal return condition  Vehicle speed: 8 km/h (5 MPH) or less
and
 Engine speed: 2,200 rpm or less
Vehicle behavior  The torque transmission cannot be performed
 There is a shock just before a vehicle stop
Malfunction detection condition Select lever and gear: Any position other than “R” position and 1GR
and
 Vehicle speed: More than 25 km/h (16 MPH)
Control at malfunction Front brake solenoid output signal; OFF
Normal return condition Other than detection condition of malfunction
Vehicle behavior Does not exist
Malfunction detection condition TCM electronic substrate temperature
145
°C (293 °F) and 120 seconds
or
150 °C (302 °F)
Control at malfunction Accelerator opening: 0.5/8 or less
Normal return condition  TCM electronic substrate temperature: Less than 140
°C (284 °F)
and
 Vehicle speed: 5 km/h (3 MPH) or less
Vehicle behavior Accelerator opening: output torque of approximately 0.5/8
Priority Detected items (DTC) Reference 1 U1000 CAN COMM CIRCUIT TM-103, "
DTC Logic"
Revision: 2010 May2011 QX56

TM-78
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
DTC Index
INFOID:0000000006226786
NOTE:
 If some DTCs are displayed at the same time, per form inspections one by one based on the priority as per
the following list. Refer to TM-77, "
DTC Inspection Priority Chart".
 The IGN counter is indicated in Freeze frame data (FFD). Refer to TM-61, "
CONSULT-III Function (TRANS-
MISSION)".
2P0615 STARTER RELAY
TM-104, "
DTC Logic"
P0705 T/M RANGE SWITCH ATM-106, "DTC Logic"
P0710 FLUID TEMP SENSOR ATM-107, "DTC Logic"
P0717 INPUT SPEED SENSOR ATM-109, "DTC Logic"
P0720 OUTPUT SPEED SENSOR TM-110, "DTC Logic"
P0740 TORQUE CONVERTERTM-128, "DTC Logic"
P0745 PC SOLENOID ATM-131, "DTC Logic"
P0750 SHIFT SOLENOID ATM-132, "DTC Logic"
P0775 PC SOLENOID BTM-133, "DTC Logic"
P0795 PC SOLENOID CTM-136, "DTC Logic"
P2713 PC SOLENOID DTM-147, "DTC Logic"
P2722 PC SOLENOID ETM-148, "DTC Logic"
P2731 PC SOLENOID FTM-149, "DTC Logic"
P2807 PC SOLENOID GTM-150, "DTC Logic"
3P0729 6GR INCORRECT RATIO
TM-114, "
DTC Logic"
P0730 INCORRECT GR RATIOTM-116, "DTC Logic"
P0731 1GR INCORRECT RATIOTM-118, "DTC Logic"
P0732 2GR INCORRECT RATIOTM-120, "DTC Logic"
P0733 3GR INCORRECT RATIOTM-122, "DTC Logic"
P0734 4GR INCORRECT RATIOTM-124, "DTC Logic"
P0735 5GR INCORRECT RATIOTM-126, "DTC Logic"
P0744 TORQUE CONVERTERTM-129, "DTC Logic"
P0780 SHIFTTM-134, "DTC Logic"
P1730 INTERLOCKTM-140, "DTC Logic"
P1734 7GR INCORRECT RATIOTM-142, "DTC Logic"
4U0300 CAN COMM DATA
TM-102, "
DTC Logic"
P0725 ENGINE SPEED TM-112, "DTC Logic"
P1705 TP SENSORTM-137, "DTC Logic"
P1721 VEHICLE SPEED SIGNALTM-138, "DTC Logic"
P1815 M-MODE SWITCHTM-144, "DTC Logic"
Priority Detected items (DTC) Reference
DTC*1
Items
(CONSULT-III screen terms) Reference
MIL*2, “ENGINE” with
CONSULT-III or GST CONSULT-III only
“TRANSMISSION”
— P0615 STARTER RELAY TM-104
P0705 P0705 T/M RANGE SWITCH A TM-106
P0710 P0710 FLUID TEMP SENSOR ATM-107
P0717 P0717 INPUT SPEED SENSOR ATM-109
P0720 P0720 OUTPUT SPEED SENSOR TM-110
Revision: 2010 May2011 QX56

TCM
TM-79
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*1: These numbers are prescribed by SAE J2012.
*2: Refer to TM-60, "
Diagnosis Description".
— P0725 ENGINE SPEED
TM-112
P0729 P0729 6GR INCORRECT RATIO TM-114
P0730 P0730 INCORRECT GR RATIOTM-116
P0731 P0731 1GR INCORRECT RATIOTM-118
P0732 P0732 2GR INCORRECT RATIOTM-120
P0733 P0733 3GR INCORRECT RATIOTM-122
P0734 P0734 4GR INCORRECT RATIOTM-124
P0735 P0735 5GR INCORRECT RATIOTM-126
P0740 P0740 TORQUE CONVERTERTM-128
P0744 P0744 TORQUE CONVERTERTM-129
P0745 P0745 PC SOLENOID ATM-131
P0750 P0750 SHIFT SOLENOID ATM-132
P0775 P0775 PC SOLENOID BTM-133
P0780 P0780 SHIFTTM-134
P0795 P0795 PC SOLENOID CTM-136
— P1705 TP SENSORTM-137
— P1721 VEHICLE SPEED SIGNALTM-138
P1730 P1730 INTERLOCK TM-140
P1734 P1734 7GR INCORRECT RATIOTM-142
— P1815 M-MODE SWITCHTM-144
P2713 P2713 PC SOLENOID D TM-147
P2722 P2722 PC SOLENOID ETM-148
P2731 P2731 PC SOLENOID FTM-149
P2807 P2807 PC SOLENOID GTM-150
— U0300 CAN COMM DATATM-102
U1000 U1000 CAN COMM CIRCUIT TM-103
DTC*1
Items
(CONSULT-III screen terms) Reference
MIL*2, “ENGINE” with
CONSULT-III or GST CONSULT-III only
“TRANSMISSION”
Revision: 2010 May2011 QX56

DIAGNOSIS AND REPAIR WORK FLOWTM-89
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
6.IDENTIFY MALFUNCTIONING SYSTEM WI TH “DIAGNOSIS CHART BY SYMPTOM”
Use TM-165, "
Symptom Table" from the symptom inspection result in step 4. Then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 8.
7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the detected malfunctioning parts.
Reconnect parts or connector after repairing or replacing, and then erase DTC if necessary.
>> GO TO 8.
8.FINAL CHECK
Perform “DTC CONFIRMATION PROCEDURE” again to make sure that the repair is correctly performed.
Check that malfunctions are not reproduced when obtai ning the malfunction information from the customer,
referring to the symptom inspection result in step 3 or 4.
Is DTC or malfunction symptom reproduced?
YES-1 >> DTC is reproduced: GO TO 5.
YES-2 >> Malfunction symptom is reproduced: GO TO 6.
NO >> Before delivering the vehicle to the customer, make sure that DTC is erased.
Question sheetINFOID:0000000006226790
DESCRIPTION
There are many operating conditions that may cause a malfunction
of the transmission parts. By understanding those conditions prop-
erly, a quick and exact diagnosis can be achieved.
In general, customers have their own criteria for a problem. There-
fore, it is important to understand the symptom and status well
enough by asking the customer about the concerns carefully. In
order to systemize all the inform ation for the diagnosis, prepare the
question sheet referring to the question points.
WORKSHEET SAMPLE
SEF907L
Question Sheet
Customer name MR/MS Engine # Manuf. Date Incident Date VIN
Model & Year In Service Date
Trans. Mileage km / Mile
Revision: 2010 May2011 QX56

TM-90
< BASIC INSPECTION >[7AT: RE7R01B]
DIAGNOSIS AND REPAIR WORK FLOW
Symptoms
† Vehicle does not move ( † Any position † Particular position )
† No upshift ( † 1GR → 2GR † 2GR → 3GR † 3GR → 4GR † 4GR → 5GR † 5GR →
6GR † 6GR → 7GR)
† No downshift ( † 7GR → 6GR † 6GR → 5GR † 5GR → 4GR † 4GR → 3GR † 3GR →
2GR † 2GR → 1GR)
† Lock-up malfunction
† Shift point too high or too low
† Shift shock or slip
† Noise or vibration
† No kick down
† No pattern select
† Others
Frequency † All the time † Under certain conditions † Sometimes ( times a day)
Weather conditions † Not affected
Weather † Fine † Clouding † Raining † Snowing † Other ( )
Te m p . † Hot † Warm
† Cool † Cold †
Temp. [Approx. °C (
° F)]
Humidity † High † Middle † Low
Transmission conditions † Not affected
† Cold † During warm-up † After warm-up
† Engine speed ( rpm)
Road conditions † Not affected
† In town † In suburbs † Freeway † Off road (Up / Down)
Driving conditions † Not affected
† At starting † While idling † While engine racing † At racing †
While cruis-
ing
† While accelerating † While decelerating † While turning (Right / Left)
† Vehicle speed [ km/h ( MPH)]
Other conditions Question Sheet
Revision: 2010 May2011 QX56

ADDITIONAL SERVICE WHEN REPLACING TRANSMISSION ASSEMBLY
TM-91
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPL ACING TRANSMISSION ASSEMBLY
DescriptionINFOID:0000000006233270
Decel G sensor calibration must be performed when replacing A/T assembly.
Special Repair RequirementINFOID:0000000006233271
1.PREPARATION BEFORE CALIBRATION PROCEDURE
1. Park the vehicle on a flat road.
2. Adjust pressure in all tires to the specified value. Refer to WT-69, "
Tire Air Pressure".
>> GO TO 2.
2.PERFORM CALIBRATION
With CONSULT-III
1. Turn ignition switch ON.
CAUTION:
Never start the engine.
2. Select “G SENSOR CALIBRATION” in “Work Support” in “TRANSMISSION”.
3. Touch “START”. CAUTION:
Never give any motion to the vehicle during the calibration.
Is
“completed” displayed?
YES >> GO TO 3.
NO >> Perform the calibration again.
3.CHECK DTC
With CONSULT-III
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Results” in “ABS”.
Is
“C1145” or “C1146” detected?
YES >> Refer to BRC-51, "DTC Index".
NO >> Calibration end.
Revision: 2010 May2011 QX56

TM-92
< BASIC INSPECTION >[7AT: RE7R01B]
ADDITIONAL SERVICE WHEN RE
PLACING CONTROL VALVE & TCM
ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE & TCM
DescriptionINFOID:0000000006233274
Decel G sensor calibration must be performed when replacing control valve & TCM.
Special Repair RequirementINFOID:0000000006233275
1.PREPARATION BEFORE CALIBRATION PROCEDURE
1. Park the vehicle on a flat road.
2. Adjust pressure in all tires to the specified value. Refer to WT-69, "
Tire Air Pressure".
>> GO TO 2.
2.PERFORM CALIBRATION
With CONSULT-III
1. Turn ignition switch ON.
CAUTION:
Never start the engine.
2. Select “G SENSOR CALIBRATION” in “Work Support” in “TRANSMISSION”.
3. Touch “START”. CAUTION:
Never give any motion to the vehicle during the calibration.
Is
“completed” displayed?
YES >> GO TO 3.
NO >> Perform the calibration again.
3.CHECK DTC
With CONSULT-III
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Results” in “ABS”.
Is
“C1145” or “C1146” detected?
YES >> Refer to BRC-51, "DTC Index".
NO >> Calibration end.
Revision: 2010 May2011 QX56

CALIBRATION OF DECEL G SENSORTM-93
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CALIBRATION OF DECEL G SENSOR
DescriptionINFOID:0000000006233272
Decel G sensor calibration must be performed when the following operation is performed.
 Removal and installation or replacem ent of yaw rate/side/decel G sensor
 Replacement of A/T assembly
 Replacement of ABS actuator and electric unit (control unit)
CAUTION:
After removing/replacing the yaw rate/side/decal G sensor or replaci ng the ABS actuator and electric
unit (control unit), the decel G sensor of the ABS act uator and electric unit (control unit) must be cali-
brated first. Refer to BRC-66, "
Description".
Special Repair RequirementINFOID:0000000006233273
CAUTION:
After removing/replacing the yaw rate/side/decal G sensor or replaci ng the ABS actuator and electric
unit (control unit), the decel G sensor of the ABS act uator and electric unit (control unit) must be cali-
brated first. Refer to BRC-66, "
Description".
1.PREPARATION BEFORE CALIBRATION PROCEDURE
1. Park the vehicle on a flat road.
2. Adjust pressure in all tires to the specified value. Refer to WT-69, "
Tire Air Pressure".
>> GO TO 2.
2.PERFORM CALIBRATION
With CONSULT-III
1. Turn ignition switch ON. CAUTION:
Never start the engine.
2. Select “G SENSOR CALIBRATION” in “Work Support” in “TRANSMISSION”.
3. Touch “START”. CAUTION:
Never give any motion to the vehicle during the calibration.
Is
“completed” displayed?
YES >> GO TO 3.
NO >> Perform the calibration again.
3.CHECK DTC
With CONSULT-III
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Results” in “ABS”.
Is
“C1145” or “C1146” detected?
YES >> Refer to BRC-51, "DTC Index".
NO >> Calibration end.
Revision: 2010 May2011 QX56