ISUZU KB P190 2007 Workshop Repair Manual

6F – 18 EXHAUST SYSTEM

Wheel Shaft End Play
Use a dial indicator to measure the wheel shaft end play.
Apply a force of 1.2 kg (2.6 lb/11.8N) alternately to the
compressor wheel end and the turbine wheel end.
W heel Shaft End Play mm (in)
Standard Limit
0.03 - 0.06
(0.001 - 0.002) 0.09 (0.004)

150RY00034
Wheel Shaft and Bearing Clearance
Use a dial indicator to measure the wheel shaft and
bearing clearance.
W heel Shaft and Bearing Clearance mm (in)
Standard Limit
0.056 - 0.127
(0.0022 - 0.0050) 0.127 (0.0050)


150RY00036

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

EXHAUST SYSTEM 6F – 19

SPECIAL TOOLS
ILLUSTRATION TOOL NUMBER TOOL NAME

901RX00143 5-8840-0075-0 Pressure
Gauge


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6F – 20 EXHAUST SYSTEM

IHI SERVICE NETWORK
For inquiries relating to turbochargers, please contact your ISUZU distributor or the nearest IHI Turbocharger
Service Facility.

HEADQUART ERS
ISHIKAWAJIMA HARIMA HEAVY INDUSTRIES CO., LTD.(IHI)
General Machinery Division
Tokyo Chuo Building 1-6-2 Marunouchi Chiyoda-ku
Tokyo 100-0005 JAPAN
TEL: 81-(3)-3286-2405 to 2407 (3 lines)
FAX: 81-(3)-3286-2430

CHINA
IHI BEIJING OFFICE
Room 705, China W orld Trade Center, No. 1 Jian Guo Men W ai Avenue
Beijing, People’s Republic of CHINA
TEL: 86-(1)-505-4997, 0408
FAX: 86-(1)-505-4350
TLX: 210343 IHIPK CN

TAIWAN
IHI TAIPEI OFFICE
Room 1202, Chia Hsin Building, No. 96 Chung Shan
North Road, Section 2, Taipei, TAIW AN
TEL: 886-(2)-542-5520, 5521, 5523
FAX: 886-(2)-542-4362
TLX: 11320 IHICO

THAILAND
IHI BANGKOK OFFICE
8th Floor, Thaniya Building, 62 Silom Road, Bangkok, THAILAND
TEL: 66-(2)-236-3490, 7356, 9099
FAX: 66-(2)-236-7340
TLX: 82375 IHICO TH

MALAYSIA
IHI KUALA LUMPUR OFFICE
Letter Box No. 52, 22nd Floor, UBN Tower,
10 Jin. P. Ramlee 50250 Kuala Lumpur, MALAYSIA
TEL: 60-(3)-232-1255, 1271
FAX: 60-(3)-232-1418
TLX: IHI KLMA 20257

INDONESIA
IHI JAKARTA OFFICE
9th Floor, Skyline Building JI. M. H. Thamrin, No. 9, Jakarta, INDONESIA
TEL: 62-(21)-32-2147, 390-2211
FAX: 62-(21)-32-3273
TLX: 44175 IHIJKT



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ACCELERATOR CONTROL 6H – 1


SECTION 6H
ACCELERATOR CONTROL


TABLE OF CONTENTS
PAGE
Removal and Installation .............................................................................................. 6H - 2 Removal ..................................................................................................................... 6H - 6
Inspection .................................................................................................................. 6H - 6
Installation ................................................................................................................. 6 H - 6

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6H – 2 ACCELERATOR CONTROL

REMOVAL AND INSTALLATION
4JA1T(L)/RHD



RTW 46HLF000301

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ACCELERATOR CONTROL 6H – 3

4JA1T(L)/LHD


RTW 46HLF000601

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6H – 4 ACCELERATOR CONTROL

4JA1TC, 4JH1TC/RHD






RTW 46HLF000201

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ACCELERATOR CONTROL 6H – 5

4JA1TC, 4JH1TC/LHD




PTW 46BMF000101


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6H – 6 ACCELERATOR CONTROL




RTW 46HMH000201

























Removal
1. Disconnect the accelerator control cable from the
accelerator pedal and dash panel.
2. Remove the cable clips.
3. Remove the accelerator control cable from accelerator control cable bracket.
1) Slide the lock in direction A
2) Rotate the ratchet ring in undirection an arrow 90 °.
4. Remove the accelerator control cable from the throttle.
Inspection
Check the following items and replace the control cable if
any abnormality is found.
• The control cable should move smoothly.
• The control cable should not be bent or kinked.
• The control cable should not be damage or
corrosion.

Installation
1. Install the accelerator control cable to accelerator control pedal dash panel.
2. Install the accelerator control cable to throttle.
Attach T-END and inner cable to throttle cam of engine.
3. Install accelerator control cable to accelerator bracket.
1) Rotate the ratchet ring in direction an arrow 90 °
until both white marking are aligned.
2) Confirm marking of outer cap must be upper side.
3) Slider the lock in direction B.
4) Confirm ratchet ring is locked.
4. Install the cable clips to accelerator control cable.

NOTE:
Confirm that the throttle (engine side) is at full stroke
when the accelerator pedal is at full stroke.




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PAGE
Section 6A Engine Mechanical .................................................................................... 1361
Section 6B Engine Cooling .......................................................................................... 1524
Section 6C Fuel System ............................................................................................... 1542
Section 6D Engine Electrical ....................................................................................... 1589
Section 6E Engine Control System ............................................................................ 1618
Section 6F Exhaust System ........................................................................................ 1986
Section 6H Engine Speed Control System ................................................................ 1998
SECTION 6
ENGINE
TA BLE OF CONTENTS
ENGINE 6
4JK
1/4J J1 MODELS

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007