wiring ISUZU TF SERIES 2004 Workshop Manual

7A2-44 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check oil temperature sensor for proper mounting
and adjustment.



DTC P0712 (FLASHING CODE 15) Transmission Oil Temperature Sensor
Circuit Low Input


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2 Perform the transmission fluid checking procedure.
Refer to checking Transmission Fluid level and
Condition in Automatic Transmission 7A section.
Was the fluid checking procedure performed ? — Go to Step 3 Refer to
Checking
Transmission
Fluid level and
Condition in
Automatic
Transmission
(AW30-40LE)
section
3

1. Install the scan tool.

2. Key “ON"
3. Review and record scan tool data.

4. Operate the vehicle with in scan tool data.
Does the scan tool indicate DTC P0712 ? — Go to Step 4 Refer to
Diagnostic Aids
4 Measure the voltage of the transmission fluid
temperature sensor by the J39200 DMM.

1. Key “OFF".
2. Disconnect the oil temperature sensor connector.

3. Key “ON".

4. Connect the J39200 DMM to the each terminal of
the oil temperature sensor connector E83-2 and
E83-1.
Does the scan tool indicate less than specified
value ? 5V Go to Step 5 Go to Step 6
5 Replace the transmission fluid temperature sensor.
Is the action complete ? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-47

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.

Check oil temperature sensor for proper mounting
and adjustment.

DTC P0713 (FLASHING CODE 16) Transmission Oil Temperature Sensor
Circuit Hight Input


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System Check performed ? — Go to Step 2 Go to OBD
System check
2 Perform the transmission fluid checking procedure.
Refer to Checking Transmission Fluid Level and
condition Automatic Transmission7A section.
Was the fluid checking procedure performed ? — Go to Step 3 Refer to
checking
Transmission
Fluid Level and
Condition
Automatic
Transmission
(AW30-40LE)
section
3

1. Install the scan tool ?

2. Key “ON"
3. Review and record scan tool date.

4. Operate the vehicle with in scan tool data.
Does the scan tool indicator DTC P0713 ? — Go to Step 4 Go to
Diagnostic Aids
4 Observe the voltage of the transmission fluid
temperature sensor on the TECH2 data.

1. Key “OFF".

2. Disconnect the transmission fluid temperature
sensor connector E-83
3. Install a fused jumper wire from terminal E83-2 to
E83-1 on the mission harness.

4. Key “ON".
Does the scan tool indicate more than specified
value ? 0.4V Go to Step 5 Go to Step 6
5 Replace the transmission fluid temperature sensor .
If the action complete ? — Verify repair —

7A2-50 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent shorto
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check input speed sensor for proper mounting and
adjustment.


DTC P0717 (FLASHING CODE 14) Input Speed Sensor Signal Error


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System check performed ? — Go to Step 2 Go to OBD
system check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data

4. Operate the vehicle with in scan tool data.
Does the scan tool indicator DTC0717 ? — Go to Step 3 Refer to
Diagnostic Aids
3 Measure voltage of the input revolution sensor by the
J39200 DMM.

1. Key “ON".
2. Engine run.

3. Disconnect the input revolution sensor connector .

4. Measure the voltage between terminal the input
revolution sensor connector E80-1 and E80-2.
Does the scan tool indicate less than specified
value ? 3V Refer to
Diagnostic Aids Go to Step 4

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-53

 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check output speed sensor for proper mounting and
adjustment.


DTC P0722 (FLASHING CODE 11) Output Speed Sensor Signal Error


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System check performed ? — Go to Step 2 Go to OBD
system check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data

4. Operate the vehicle with in scan tool data.
Does the scan tool indicator DTC 0722 ? — Go to Step 3 Refer to
Diagnotic Aids
3 Measure the voltage of the output revolution sensor
by the J39200 DMM.

1. Key “OFF"
2. Lift the driving wheels.

3. Disconnect the output revolution sensor connector.

4. With engine idling in gear.
5. Measure the voltage between the output revolution
sensor connector terminal E81-1 and E81-2.
Does the scan tool indicate less than specified
value ? 3V Refer to
Diagnostic Aids Go to Step 4

7A2-56 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.
 After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.5 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short
oropen condition, move the wiring harness while
observing test equipment for a change.


DTC P0743 (FLASHING CODE 33) Torque Converter Clutch Electrical


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data.

4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0743? — Go to Step 3 Refer to
Diagnostic Aids
3

1. Key “ON", engine run.

2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-5 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-59


DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.


DTC P0748 (FLASHING CODE 35) Pressure Control Solenoid Malfunction


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data.

4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0748? — Go to Step 3 Refer to
Diagnostic Aids
3 Perform the transmission fluid checking procedure.
Refer to checking Transmission Fluid level and
Condition in Automatic Transmission 7A section.
Was the fluid checking procedure performed? — Go to Step 4 Refer to
checking
Transmission
Fluid level and
Condition in
Automatic
Transmission
(AW30-40LE)
section

7A2-62 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Action Taken When The DTC Sets

The TCM operates shifting as following pattern.



Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off

No squat control.
 No engine torque control.

No line pressure control.

No lock-up control.
 No slope control.

Check Trans ON.

DTC stored.

No detect DTC P0722

No detect DTC P0717

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.


DTC P0753 (FLASHING CODE 31) Shift Solenoid S1 Electrical


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data.

4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0753? — Go to Step 3 Refer to
Diagnostic Aids
3

1. Key “ON", engine run.

2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-16 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-65

Action Taken When The DTC Sets
The TCM operates shifting as following patterns.



Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off

No squat control.
 No engine torque control.

No line pressure control.

No lock-up control.
 No slope control.

No torque reduction.

Check Trans ON.

DTC stored.

No detect DTC P0722.

No detect DTC P0717.

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring .
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.


DTC P0758 (FLASHING CODE 32) Shift Solenoid S2 Electrical


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".

3. Review and record scan tool data.
4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0758? — Go to Step 3 Refer to
Diagnostic Aids
3

1. Key “ON", engine run.

2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-15 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10

7A2-68 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)


 Engine REV is 7000 rpm.

Coolant tempreature is 80

C.

No detect DTC P0712, 0713.
 No detect DTC P0560.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.

Inspect the wiring for EMI (Erectro-Magnetic
Interference). Check that all wires are properly
routed away from coil, and generator. Also check fo
r
improperly installed electrical options. When this test
is performed, turn “OFF" on electronic autoparts
switches to improperly for a noise preventing.

7A2-70 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P1790 (FLASHING CODE 61) Transmission Control Module ROM
Checksum Error
Circuit Description
The electrically erasable programable read only
memory (EEPROM) is a permanent memory chip that is
physically solenoid within the TCM. The EEPROM
contans the program and the calibration information
that the TCM needs to control powertrain operation.
Unlike the PROM used in past applications, the
EEPROM is not replace able. If the TCM is replaced,
the new TCM will need to be programmed. Equipment
containing the correct program and calibration for the
vehicle is required to program the TCM.
Condition for setting the DTC
The TCM detects incorrect value of ROM checksum.
Action Taken When The DTC Sets

Check Trans ON.
 DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.5 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.