ISUZU TF SERIES 2004 Workshop Manual
Page 571 of 4264
CAB 10-63
INSTALLATION (REGULAR CAB RHD MODEL)
686R300017
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate
Page 572 of 4264
10-64 CAB
INSTALLATION (EXTEND CAB RHD MODEL)
686R300019
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate
Page 573 of 4264
CAB 10-65
INSTALLATION (CREW CAB RHD MODEL)
686R300013
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Center pillar lower trim cover
6. Rear sill plate
7. Front sill plate
Page 574 of 4264
10-66 CAB
INSTALLATION (REGULAR CAB LHD MODEL)
RTW4A0LF000401
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate
Page 575 of 4264
CAB 10-67
INSTALLATION (EXTEND CAB LHD MODEL)
RTW4A0LF000501
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate
Page 576 of 4264
10-68 CAB
INSTALLATION (CREW CAB LHD MODEL)
RTW4A0LF000601
Installation Steps
1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Center pillar lower trim cover
6. Rear sill plate
7. Front sill plate
Page 577 of 4264
CAB 10-69
Important Operation - Installation
1. Fuel Filler Lid Cable Assembly
Install the cable holder of cable assembly to the recess
and push the grommet in to the back panel. Fix the clips
to the pointed places.
Note:
To install, follow the removal steps in the reverse order,
noting the following points.
Do not make extreme curve on the cable.
Install the cable from inside of the cab.
Page 578 of 4264
10-70 CAB
QUARTER GLASS (EXTEND CAB)
REMOVAL AND INSTALLATION
RTW4A0MF000101
Removal Steps
1. Body side rear trim covers
2. Hinge/Faster
3. Quarter glass
4. Weather strip
Installation Steps
4. Weather strip
3. Quarter glass
2. Hinge/Faster
1. Body side rear trim covers
Important Operation - Removal
1. Body Side Rear Trim Covers Refer to Interior Trim Panels in this section.
Important Operation – Installation
4. Weather Strip Install the weather strip by aligning to corners with white
mark to the upper coners on the body panel.
Page 579 of 4264
CAB 10-71
FRONT SEAT
REMOVAL AND INSTALLATION
RTW3A0MF000301
Removal Steps
1. Front cover
2. Rear cover
3. Bolt
4. Seat assembly
5. Side seat belt buckle/Pretensioner seat
belt/Center seat belt
6. Seat adjuster
Installation Steps
6. Seat adjuster
5. Side seat belt buckle/Pretensioner seat
belt/Center seat belt
4. Seat assembly
3. Bolt
2. Rear cover
1. Front cover
Page 580 of 4264
10-72 CAB
Important Operations - Removal
1. Front Cover
While pushing the cover downward, pull it.
4. Seat Assembly
Disconnect the seat belt warning harness connecto
r
(Driver’s side only).
5. Side Seat Belt Buckle/Pretensioner Seat Belt/Center
Seat Belt
Remove the seat belt fixing screw and the warning
harness connector clip (Bucket seat model).
RTW4A0SH000101-X
Remove the pretensioner seat belt fixing screw and the
warning harness connector (With pretensioner seat bel
t
model).
24.jpg
Remove the seat belt fixing screws and the warning
harness connector clip (Bench seat model).
Important Operations – Installation
5. Buckle Side Seat Belt/Pretensioner Seat Belt/Center
Seat Belt
Tighten the seat belt fixing screws to the specified
torque.
Torque N
m (kgf
m/lb
ft)
40 (4.1 / 30)