oil filter JAGUAR X308 1998 2.G Workshop Manual

            303‐07:  En gine  Ignition
 
                 Specification  
                 Diagnosis  and  Testing  
                     Engine Ignition  
                 Diagnosis  and  Testing  
                     Engine Ignition  
                 Inspection  and Verification  
                     Driver Information  Chart  
                     Default mode Definitions  
                     Diagnostic Trouble  Code  (DTC)  index  
                     Pinpoint Tests  
                 Removal and  Installation  
                     Ignition Coil ‐On ‐Plug  LH  (18.20.44)  
                     Ignition Coil ‐On ‐Plug  RH  (18.20.43)  
                     Ignition Module  (18.20.30)  
                     Spark Plugs (18.20.02)  
 
             303‐08:  En
gine  Emission  Control  
                 Specification  
                 Diagnosis  and  Testing  
                     Engine Emission  Control  
                 Inspection  and Verification  
                     Diagnostic Trouble  Code  (DTC)  Index  
                     Pinpoint Tests  
                 Removal and  Installation  
                     Exhaust Gas  Recirculation  (EGR) Valve  (17.45.01)  
                     Exhaust Manifold  to  Exhaust  Gas  Recirculation  (E
GR)  Valve  Tube  (17.45.11)  
 
             303‐12:  Intake  Air  Distribution  and  Filtering  
                 Removal and  Installation  
                     Air Cleaner  (19.10.05)  
                     Air Cleaner  Element  (19.10.08)  
                     Charge Air  Cooler  LH  (18.50.19)  
                     Charge Air  Cooler  RH  (18.50.18)  
                     Charge Air  Cooler  Gasket  LH  (18.50.22)  
                     Charge Air  Cooler  Gasket  RH  (18.50.21)  
                     Supercharger  (18.50.
15) 

                    Knock Sensor  (KS)  RH  (18.30.93)  
                    
Variable Camshaft  Timing  (VCT)  Oil  Co ntrol
 
Solenoid  (18.30.90)  
 
        
307:  Automatic  Transmission/Transaxle  
 
             307‐01A : Automatic  Transmission/Transaxle  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Ve
hicle  Repair  
                     Electronic Pressure  Control (EPC)  Solenoid  (44.15.51)  
                     Extension Housing  Seal  (44.20.18)  
                     Extension Housing  O ‐Ring  Seal  (44.20.19)  
                     Main Control  Valve Body  (44.40.01)  
                     Output Shaft  Speed  (OSS)  Sensor  (44.15.41)  
                     Shift Solenoids  (SS)  (44.15.50)  
                     Transmission  Control Module  (TCM)  (44.15.32)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  (44.24.04)  
                     Transmission  Fluid Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  (44.15.35)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Range (TR)  Sensor  
                     Transmission  Support Insulator  (12.45.04)  
                     Turbine Shaft  Speed  (TSS)  Sensor  (44.15.40)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Sh
aft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
Mass
 
Airflow
 
Sen s
or
 
Knock
 Sensor
 (KS)
 LH
 (18.30.92)
 

            310‐01:  Fu el Tank  and  Lines  
                 Removal and  Installation  
                     Fuel Level  Sensor  (88.25.32)  
                     Fuel Pump  (19.45.08)  
                     Fuel Tank  (19.55.01)  
 
             310‐02
:
 Acceleration  Control  
                 General Procedures  
                     Accelerator  Cable  Adjustment  (12.20.05)  
                 Removal and  Installation  
                     Accelerator  Cable  (19.20.06)  
 
             310‐03:  Speed  Control  
                 Diagnosis  and  Testing  
                     Speed Con
trol 
 
    4:  Electrical  
 
        412:  Climate  Control  System  
 
             412‐00:  Climate  Control  System  ‐ General  Information 
                 Specification  
                 Description  and  Operation  
                     Climate Control System  
                 Diagnosis  and  Testing  
                     Climate Control System  
                 General Procedures  
                     Air Conditioning  (A/C)  System  Check ‐  Retail Procedure  
                     Air Conditioning  (A/C)  System  Recovery,  Evacuation  and  Charging  (82.30.30)  
                     Contaminated  Refrigerant  Ha
ndling  
                     Manifold Gauge  Set Connection  
                     Refrigerant  Adding (82.30.02)  
                     Refrigerant  Oil Adding  
                     Refrigerant  System Tests  
 
             412‐01:  Air  Distribution  and  Filtering  
                 Description  and  Operation  

diverter val
ve (if fitted) and oil filter.
Main
bearings
which are grooved in the upper positions and plain in
the lower positions. They are manufactured from
aluminium / tin material.
A c
rankshaft with under
cuts and rolled fillets for extra strength.
Fracture
-split connecting rods in sintered-forged steel.
Brackets
bolted to the front of
the cylinder
block are used to mo unt all accessories.
A sin
gle, seven ribbed vee belt
drives the accessories.
An au
tomatic belt tensioner for the front accessory drive,
incorporating a wear indicator.
An advanced en
gine management system inco
rporating electronic throttle control.
The un
it meets the requirements of the CARB OBDII USA legislation.
Ancillary Systems
The an
ci
llary systems, driven by the engine, each have a
detailed Description and Operation along with Diagnostic
Procedures, and Removal and Installation instructions ; refer to the following sections of this manual:
Power Steeri
ng Pump - Section 211-02
Ai
r Conditioning Compressor - Sectio
n 412-03
Engine
C
ooling Pump - Section 303-03
Generator
- Sectio
n 414-02
The drive belt, idler pulley and automatic tensioner are described in Section 303-05.
The engine starting system is described in Section 303-06.
En
gine Management and Emission Control System
Engine Control Modu
le (ECM)
Engine
management and exhaust emissions are controlled by the ECM, which has the
following main functions:
Fu
el injection
Idle
s
peed
Ignition Ev

aporative loss system
Engine
cooling fans Clim
ate control compressor clutch demand
The microprocessor within the ECM receiv es signals from various sensors and other modules and uses a pre-determined
program to compute engine management functions.
Adaptive functions are incorporated in the ECM to cater for co ntinuous adjustments to its computations to suit prevailing
conditions. Because the system also controls emissions to suit all modes, neither CO levels nor idle speed require service
attention or adjustment, except if an error should occur.
On Board Diagnostics are controlled by the ECM with the continuous monitoring of incoming signals and the subsequent
verification against what the module expects to 'see'. Should a si gnal be incorrect or missing, the ECM will substitute a fixed
value to provide the 'limp home mode' and alert the driver of the problem. Fixed values may be adopted for:
Transmission oil
temperature
Mechanica
l
guar
d position
Throttle blade angle Camshaft position

Inta
k
e air temperature
Diagnostic trouble codes (DTC), including OBD II codes, are stored in the ECM memo ry and can be read by an appropriate
retrieval tool.
Should either the ECM or TCM fa il, ensure that the control housing cooling fan is operating correctly. Failure of the cooling
fan MUST be rectified before renewing a control module and details of a fa n failure should accompany a returned control
module.

I
nstallation

Tigh
ten each bolt to 8 to 12 Nm initial torque value.
Ti

ghten to a final torque of 57 to 63 Nm.
27. Check that the cranks haft turns freely.
28. Repeat the previous operations for each connecting rod
bearing as necessary.
1. Install the oil pan bo dy assembly. Refer to Operation 12.60.48.


2. Po
sition and align the oil pan gasket to the oil pan body
assembly.
Inse
rt the seal into the locating positions in the groove,
working around from a corner.
Press in the remai
nder of th
e seal, following the same
procedure.

3. Install th
e oil pan to the oil pan body.
1. Position and align the oil pan.
2. Install, but do not tighte n, all eighteen bolts which
secure the oil pan.

4. Tigh
ten the bolts to the correct
torque figure 11-13 Nm, in the
sequence indicated.
Tigh
ten the drain plug to 30-40 Nm.
Install a new oil

filter.

3. Tighten the bolts to the correct torque figure 11 - 13 Nm, in
the sequence indicated.
Tighten the drain plug to 30 - 40 Nm.
Fit a new oil filter.
4. NOTE: When the engine is star ted from cold and run for a
short period only, before being swit ched off, a quantity of oil will
be 'hung up' within the engine because it is not up to operating
temperature.
Should the oil level subsequently be topped-up, the level could
become too high, causing oil burning.
Typically, 0.875 L is hung up.
Lower the ramp. Refill the engine with the correct specification
engine oil.
5. Remove the paint protection sheets and close the engine
compartment.

Engine - Oil Pressure Switch
In-vehicle Repair
Removal
Installation

1.
Raise vehicle on four post ramp.

2. Remove oil pressure switch.
Disconnect connector.
Remove oil pressure switch from oil filter head.

1. NOTE: Fit new sealing washer to oil pressure switch.
Installation is reverse of removal.

Engine - Upper Oil Pan3.2L NA V8 - AJ26
In-vehicle Repair
Removal
Special Tool(s)

Installer/remover, Oil Filter
303-752

1. Disconnect the batt ery ground cable.
Remove the battery cover.
2. Open the engine compartment and fit paintwork protection
sheets.
3. Set the engine compartment cover to the service access
position.
4. Remove the timing cover and al l associated components, as
detailed in Operation 12.65.01.
5. Remove both front wheel and tyre assemblies. Refer to
Operation 74.20.05.
6. Remove the undertray. Re fer to Operation 76.22.90.

7. Remove the two bolts which secu re the generator cooling duct
to the oil pan body and remove the duct.
8. Remove the front cross member for access. Refer to Operation
76.10.05.
9. Drain the engine oil.
1. Position the waste oil bowser.
2. Remove the drain plug from the oil pan and drain the engine oil.
Fit a new sealing washer to the drain plug.

Wipe the drain plug and install it to the oil pan to prevent
oil dripping.
Move the oil bowser away from the vehicle.

10. Remove the oil pan.
1. Remove the eighteen bolt s which secure the oil pan
to the oil pan body.
2. Remove the oil pan.
3. Remove the gasket from the oil pan body assembly.

11. NOTE: Place a suitable container underneath filter to prevent
oil spillage.
Using the special tool, remove the oil filter.
12. Remove the oil pressure switch.
For additional information, refer to Oil Pressure Switch
- in this
section.

13. Remove the crankshaft position sensor.
1. Remove the bolt which secures the crankshaft position sensor to the flywheel housing.
2. Remove the access grommet from the housing.
Remove the sensor and allow it to hang free under the
engine.
Release the harness clips from the oil pan body.
14. Remove the bolt which secures the transmission cooler pipes
and remove the clamping bracket.

Installation


19. Remove the eight screws an d release the windage tray.

20. Remove the oil filter adaptor.
21. Clean all components and releva nt mating faces; cylinder
block, oil pan, oil pan body, wi ndage tray, oil pick-up pipe and
timing cover.
1. Reposition the windage tray and install the eight screws,