charging JAGUAR X308 1998 2.G Workshop Manual

                    Coolant E x
pansion
 Tank  (26.15.01)  
                    
Coolant Outlet  Pipe  (26.31.08)  
                    
                     Cooling Fan  Motor  (26.25.24)  
                     Cooling Fan  Motor  and  Shroud  (26.25.25)  
                     Cooling Fan  Motors  (26.25.25)  
                     Cooling Fan  Shroud  (26.25.30)  
                     Engine Coolant  Level  Switch  (26.40.11)  
                     Radiator (26.40.01)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Radiator (26.40.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Radiator Lower Hose  (26.30.07)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Radiator Lower Hose  (26.30.07)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Radiator Upper Ho
se (26.30.01)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Radiator Upper Hose  (26.30.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  (26.45.07)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Thermostat  (26.45.07)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  Housing  Cover  (26.
45.22)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Thermostat  Housing  Cover  (26.45.22)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  Housing  Cover  Seal  (26.45.20)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Thermostat  Housing  Cover  Seal  (26.45.20)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Water Pump  (26.50.
01) ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Water Pump  (26.50.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Water Pump  Pulley  (26.50.05)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Water Pump  Pulley  (26.50.05)  ‐ 4.0L  SC  V8 ‐ AJ26  
 
             303‐03B : Supercharger  Cooling 
                 Removal and  Installation  
                     Water Pump  
 
             303‐04:  Fu
el Charging  and Controls  
                 Diagnosis  and  Testing  
                     Fuel Charging  and Controls  
                 Inspection  and Verification  
                     Driver Information  Chart  
                     Default mode Definitions  
                     Diagnostic Trouble  Code  (DTC)  index  
                     Pinpoint Tests  

            310‐01:  Fu el Tank  and  Lines  
                 Removal and  Installation  
                     Fuel Level  Sensor  (88.25.32)  
                     Fuel Pump  (19.45.08)  
                     Fuel Tank  (19.55.01)  
 
             310‐02
:
 Acceleration  Control  
                 General Procedures  
                     Accelerator  Cable  Adjustment  (12.20.05)  
                 Removal and  Installation  
                     Accelerator  Cable  (19.20.06)  
 
             310‐03:  Speed  Control  
                 Diagnosis  and  Testing  
                     Speed Con
trol 
 
    4:  Electrical  
 
        412:  Climate  Control  System  
 
             412‐00:  Climate  Control  System  ‐ General  Information 
                 Specification  
                 Description  and  Operation  
                     Climate Control System  
                 Diagnosis  and  Testing  
                     Climate Control System  
                 General Procedures  
                     Air Conditioning  (A/C)  System  Check ‐  Retail Procedure  
                     Air Conditioning  (A/C)  System  Recovery,  Evacuation  and  Charging  (82.30.30)  
                     Contaminated  Refrigerant  Ha
ndling  
                     Manifold Gauge  Set Connection  
                     Refrigerant  Adding (82.30.02)  
                     Refrigerant  Oil Adding  
                     Refrigerant  System Tests  
 
             412‐01:  Air  Distribution  and  Filtering  
                 Description  and  Operation  

 
     413‐08: Information  and  Message  Ce nter  
                 Descriptio
n
 and  Operation  
                     Information  and  Message  Center  
                 Diagnosis  and  Testing  
                     Information  and  Message  Center  
                 Removal and  Installation  
                     Message Center  Switch  (86.66.11)  
 
             413‐13:  Parking  Aid 
                 Description  and  Operation  
                     Parking Aid  
                 Diagnosis  and  Testing  
                     Parking Aid  
                 Removal and Installation  
                     Parking Aid  Module  (86.80.39)  
                     Rear Parking  Aid  Sensor  (86.54.
14) (86.62.01)  
                     Rear Parking  Aid  Speaker  (86.54.19)  (86.62.02)  
 
        414:  Battery  and  Charging  System  
 
             414‐00:  Battery  and  Charging  System ‐ General  Information  
                 Description  and  Operation  
                                         
                     
             414
‐01:  Battery,  Mounting  and  Ca
bles  
                 Description
 and  Operation  
                     Battery
 and  Cables  
                 General
 Procedures  
                     Battery
 Connect  (86.15.15)  
                 Removal
 and  Installation  
                     Battery
 (86.15.01)  
                     Battery
 Ground  Cable  (86.15.19)  
                     Battery
 Positive  Cable  (86.15.17)  
                     Battery
 Retaining  Bracket  (86.15.12)  

Pinpoint tests

W
S
S circuit: short
circuit to power
WSS f
ailure
C1
175Left -hand re
ar wheel speed
sensor (WSS) circuit failure
W S
S circuit: open
circuit
WS
S circuit: short
circuit to ground
W S
S circuit: short
circuit to power
WSS f
ailure
F
or l
eft-hand rear WSS test
s. GO to Pinpoint Test E.
C1267Modulat or valv
e failure
Supply volt
ages
to valve
solenoids or sensors out of range
Fo
r power and ground tests. GO to Pinpoint Test
A.
B1342CAN co
mmunication circuit
failure
CAN :
open circuit fault

CAN:
short circuit to
ground
CAN :
short circuit to
power
Fo
r CAN tests. GO to Pinpoint Test
F.
B1676Supply volt
age out of range
Supply voltage:
too
low
Supply volt age:
too
high
Check fo
r DTCs indicating a charging system fault.
Rectify as necesssary.
PI
NPOINT TEST A : MODULE
POWER AND GROUND SUPPLIES
TES
T
CONDITIONS
D E
TAILS/RESULTS/ACTIONS
A
1
: CHECK THE POWER SUPPLY FUSES
Make sure the igniti
on is turned off. 1
Chec
k fuses 04, 16 and 18 of the engine compartment junction box.
2
Are th
e fus
es in good condition?
Yes GO to A2
.
No
Install a new f
use as
necessary. Check the syst em for normal operation. If the fuse fails again,
check the circuit for a short circuit to ground. Refer to the electrical guides.
A2: CHECK THE PERMANENT
POWER SUPPLY (1) TO THE MODULE
Disc

onnect the ABS module connector, LF27.
1
Measure the voltage between LF
2
7, pin 09 (NR) and ground.
2
Is the vol
t
age greater than 10 volts?
Yes GO to A3
.
No Re
pair the circuit between the engine compartment
junction box, fuse 16, and LF27 pin 09. Refer to
the electrical guides. Clear the DTC, check for normal operation.
A3: CHECK THE PERMANENT
POWER SUPPLY (2) TO THE MODULE
Meas
ure t
he voltage between LF27, pin 25 (NW) and ground.
1
Is the vol
t
age greater than 10 volts?
Yes GO to A4
.
No
Re
pair the circuit between the engine compartment ju
nction box, fuse 18, and LF27 pin 25. Refer to
the electrical guides. Clear the DTC, check for normal operation.
A4: CHECK
THE IGNITION POWER SUPPLY TO THE MODULE
Make sure the ignition is on. 1
Measure the
voltage between LF 2
7, pin 20 (WU) and ground.
2
Is the vol
t
age greater than 10 volts?
Yes GO to A5
.
No Re
pair the circuit between the engine compartment ju
nction box, fuse 04, and LF27 pin 20. Refer to
the electrical guides. Clear the DTC, check for normal operation.
A5: CHECK
THE GROUND SUPPLY TO THE MODULE

Fuel Char
ging and Controls - Fuel Charging and Controls
Description an
d Operation

This section provides service informatio n for the fuel distribution components located on the engine and includes the
supercharger, where fitted. Refer to Section 310-01 for informatio n on the fuel tank, fuel lines and related fuel supply items.

Fuel Charging and Controls -
Normally Aspirated Vehicles

P
a
rts List
It
e
m
Par
t
Number
De
scr
iption
1—F
u
el feed from tank to bank 2
2—Fue
l
injector
3—Inta
k
e manifold/fuel rail
4—Te
st
/de-pressurization valve
5—F
u
el cross-over pipe
6—F
u
el pressure regulator
7—F
u
el return to tank

Fuel Char
ging and Controls - Fuel Charging and Controls
D
iagn
osis and Testing
I
n
spection and Verification
1.
1. Veri fy the customer concern.
2. 2. Confi
rm which, if any, warning li
ghts and/or messages were displayed on the instrument cluster.
• NOTE: If any warning lights and/or me ssages were displayed when the fault occurred, refer to the Driver Information
table for DTCs associated with the display, then to the DTC index table for possible sources and actions. Some warnings will
appear to clear when the ignition is cycl ed. This is often because the warning has flagged as a resu lt of one of the vehicle's
on-board diagnostic routines having run to detect the fault. If the same routine is not run when the ignition is switched ON,
the warning will not reflag until the routine does run. See the DTC summaries for drive cycle routines.
3. 3. Visually inspect for obvious signs of mechanical or electrical damage.
Vi
sual Inspection Chart
4.
4. Veri fy the foll
owing syst
ems are working correctly:
Air intake
system
Cooling system


Charging system
5. 5. If
an obvious cause for an observed or
reported concern is found, correct th e cause (if possible) before proceeding
to the next step.
6. 6. Where the Jaguar approved diagnostic sy stem is available, complete the S93 report before clearing any or all fault
codes from the vehicle.
• NOTE: If a DTC cannot be cleared, then there is a permanent fault present that flag s again as soon as it is cleared (the
exception to this is P1260, which will only clear following an ignition OFF/ON cycle after rectification).
7. 7. If the cause is not visually evident and the Jaguar approv ed diagnostic system is not available, use a fault code
reader to retrieve the fault codes be fore proceeding to the Diagnostic Trou ble Code (DTC) Index Chart, or the
Symptom Chart if no DTCs are set.
• NOTE: If the DTC flagged was not present for two or more co nsecutive cycles, it is classed as temporary, and will be
deleted following three cycl es during which no fault was present. This could result in a reported wa rning light/message with
no stored DTCs. If a fault is present for three consecutive cycles, the DTC becomes permanent, and will remain in the
module's memory for 40 drive cycl es (a cycle is an ignition OFF/ON, which will occur during the owner's normal use of the
vehicle. No action on the part of the technician is necessary to perform this cycle. A drive cycle is a series of conditions
needed to make the on-board diagnostic ro utine run, and may need a specific action on the part of the technician. See the
DTC summaries for drive cycle routines).
8. 8. Using the Jaguar approved diagnostic system where available, and a scan tool where not, check the freeze frame
data for information on the conditions applicable when the fault was flagged. The format of this will vary,
depending on the tool used, but can pr ovide information useful to the technician in diagnosing the fault.
MechanicalElectrical
Engine
oil level
Coo
ling system coolant
lev
el
Fuel contamination
Throttle body Poly-ve
e belt
Fu
ses
W
i
ring harness
E
l
ectrical connector(s)
Sens
o
r(s)
Engine
control module (E
CM)
Tran
s
mission control module
Check spark plu
g type. Only r
e
sisted plugs should be fitted. Refer to specifications
section for gap
Relay date codes. I
f the date on the rela
y is between R6 k1 and R6 k8, replace the
relay

Fuel Charging and Controls
- Fuel Injector4.0L SC V8 - AJ26
Rem
oval and Installation
Remov

al
Installation

1.

Disconnect battery ground cabl e (IMPORTANT, see SRO 86.15.19
for further information).
2. WARNING: BEFORE PROCEEDING, IT IS ESSENTIAL THAT
THE WARNING NOTES GIVEN IN SECTION 100-00 (UNDER THE
HEADING 'SAFETY PRECAUTIONS') ARE READ AND UNDERSTOOD.
Depressurize fuel system; refer to 19.50.02.

3.

Disconnect injector connector.
1. Disconnect and reposition bank 1 or 2 fuel injector harness connector to allow access to injector.
2. Loosen but do not remove nut securing injector harness support bracket to camshaft cover. Reposition injector
harness to allow access to injector.
3. Detach injector connector.

4.

Remove fuel injector.
1. Prise out injector retaining clip, ensuring that it is not ejected and lost. Note orientation of clip.
2. Using a suitable implement, carefully lever injector from
fuel rail.
3. Discard injector O-rings.
5. Clean all mating faces.
1. Install fuel injector.
1. Install new O-rings, lubricat ed with petroleum jelly, to
fuel injector.
2. Install fuel injector into fuel rail. Press firmly until it is felt to click into place.
3. Hold injector firmly down and install injector securing clip in correct orientation.
2. Re-connect injector and harness connectors.
3. Tighten harness nut to 4-5Nm.
4. Reconnect battery ground cable (IMPORTANT, see SRO 86.15.15
for further information).

Fuel Charging and Controls - Throt
tle Body Gasket
Re
mo
val and Installation
Remov
a
l
Installation

1.
Re
move throttle body; refer to 19.70.04.
1. Installation is a reversal of the removal procedure.

Engine Igni
tion -
Engine Ignition
D
iagnosis and Testing
I

nspection and Verification
1.
1. Veri
fy the customer concern.
2. 2. Confirm which, if any, warning li ghts and/or messages were displayed on the instrument cluster.
• NOTE: If any warning lights and/or me ssages were displayed when the fault occurred, refer to the Driver Information
table for DTCs associated with the display, then to the DTC index table for possible sources and actions. Some warnings will
appear to clear when the ignition is cycl ed. This is often because the warning has flagged as a resu lt of one of the vehicle's
on-board diagnostic routines having run to detect the fault. If the same routine is not run when the ignition is switched ON,
the warning will not reflag until the routine does run. See the DTC summaries for drive cycle routines.
3. 3. Visually inspect for obvious signs of mechanical or electrical damage.
V
isual Inspection Chart
4.
4. Veri
fy the following syst
ems are working correctly:
Air in
take system
Coo

ling system
Charging system


F

uel charging system
5. 5. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding
to the next step.
6. 6. Where the Jaguar approved diagnostic sy stem is available, complete the S93 report before clearing any or all fault
codes from the vehicle.
• NOTE: If a DTC cannot be cleared, then there is a permanent fault present that flag s again as soon as it is cleared (the
exception to this is P1260, which will only clear following an ignition OFF/ON cycle after rectification).
7. 7. If the cause is not visually evident and the Jaguar approv ed diagnostic system is not available, use a fault code
reader to retrieve the fault codes be fore proceeding to the Diagnostic Trou ble Code (DTC) Index Chart, or the
Symptom Chart if no DTCs are set.
• NOTE: If the DTC flagged was not present for two or more co nsecutive cycles, it is classed as temporary, and will be
deleted following three cycl es during which no fault was present. This could result in a reported wa rning light/message with
no stored DTCs. If a fault is present for three consecutive cycles, the DTC becomes permanent, and will remain in the
module's memory for 40 drive cycles (a cy cle is an ignition ON/OFF, which will occur during the owner's normal use of the
vehicle. No action on the part of the technician is necessary to perform this cycle. A drive cycle is a series of conditions
needed to make the on-board diagnostic ro utine run, and may need a specific action on the part of the technician. See the
DTC summaries for driv e cycle routines).
8. 8. Using the Jaguar approved diagnostic system where available, and a scan tool where not, check the freeze frame
data for information on the conditions applicable when the fault was flagged. The format of this will vary,
depending on the tool used, but can pr ovide information useful to the technician in diagnosing the fault.
CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit,
part number 3548-1358-00.
MechanicalElectrical
Engi
ne oil level
Coo

ling system coolant
level
Fuel contamination

Throttle body Poly

-vee belt
F
uses
W

iring harness
E

lectrical connector(s)
Sens

or(s)
Engine

control module (ECM)
Relay date codes.

If the date on the relay is between R6 k1 and R6 k8, replace
the relay

• NO
TE: When performing electrical voltag
e or resistance tests, always use a digital multimeter (DMM) accurate to 3
decimal places, and with an up-t o-date calibration certificate. When testing resistance, always take the resistance of the
DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic ro utines involving pinpoint tests.
Sym
ptom Chart
Sy
m
ptom
Possib
l
e source
Acti
o
n
Engine
cranks, but does
not fire
Secu
rit
y system /Immobiliser
engaged
Harness Fue l
system
ECM fault

Contact deal er techni
cal support for
information on security system. Check fuel
system pressure,
REFER to: Fuel System Pressure Check
(310
-
00 Fuel System - Genera l Information, General
Procedures).
For ECM tests,
REFER to: Electronic Engine Controls
(303
-14
Electronic Engine Co ntrols, Diagnosis and
Testing).
Engine cranks and
fi
res, but will not
start
Fu
el pump relay
Fuel

pump
Cyl
i
nder compression loss
(short-term. Refer to bulletin; 303-52)
Engine coolan t
temperature
(ECT) sensor
Spark plugs fouled, gapp
ed
incorrectly
Ignition coil fail
ure(s)
Check f
o
r water ingress into
spark plug wells
HT sho rt to ground (tracking)
check rubber
boots for
cracks/damage
Fo
r fuel pump relay tests,
REFER to: Fuel Charging and Controls
(303
-04

Fuel Charging and Controls, Diagnosis and Testing).
Check fuel pressure,
REFER to: Fuel System Pressure Check
(310
-
00 Fuel System - Genera l Information, General
Procedures).
For compression loss, REFER to the technical service bulletins. For ECT sensor tests,
REFER to: Electronic Engine Controls
(303
-14
Electronic Engine Co ntrols, Diagnosis and
Testing).
For spark plug tests, GO to Pinpoint Test B.
.
For ign i
tion system tests, GO to Pinpoint Test
A.
.
Diff
icult to start cold
Batt
ery Fuel
pump
Cyl
i
nder compression loss
(short-term. Refer to bulletin; 303-52)
Spark plugs fouled, gapp
ed
incorrectly
F o
r battery information,
REFER to: Battery and Cables
(414
-01 Battery,

Mounting and Cables, Description and Operation).
Check fuel pressure.
REFER to: Fuel System Pressure Check
(310
-
00 Fuel System - Genera l Information, General
Procedures).
For compression loss, REFER to the technical service bulletins. For spark plug tests, GO to
Pinpoint Test B.
. For ig
nition system tests, GO
to Pinpoint Test A.
.
Diff
icult to start hot
Roc
h
ester valve
Injec
t
or leak
Purge
val
ve
Fue
l
pump
Engine coolan
t
temperature
(ECT) sensor
F or R
ochester
valve test,
REFER to: Electronic Engine Controls
(303
-14
Electronic Engine Co ntrols, Diagnosis and
Testing).
For injector leak test, REFER to technical
service bulletins. Check fuel pressure. For evaporative emissions components,
REFER to: Evaporative Emissions
(303
-13
Evaporative Emissions, Diagnosis and Testing).
For ECT sensor tests,
REFER to: Electronic Engine Controls
(303
-14
Electronic Engine Co ntrols, Diagnosis and
Testing).
D iff
icult to start after hot soak
(vehicle standing after engine has reached operating temperature)
Roc h
ester valve
Injec
t
or leak
Purge
val
ve
Fue
l
pump
Engine coolan
t
temperature
(ECT) sensor
F or R
ochester
valve test,
REFER to: Electronic Engine Controls
(303
-14
Electronic Engine Co ntrols, Diagnosis and
Testing).
For injector leak test, REFER to technical service bulletins. Check fuel pressure,
REFER to: Fuel System Pressure Check
(310
-
00 Fuel System - Genera l Information, General
Procedures).