JAGUAR XFR 2010 1.G Workshop Manual
Page 1231 of 3039
12.
13.
CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
14. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.
Raise and support the vehicle.
15. Refer to: Engine Mount RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
16. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
Left-hand drive vehicles
17.
Page 1232 of 3039
18.
All vehicles
19.
20. NOTE: Engine shown removed for clarity. www.JagDocs.com
Page 1233 of 3039
21.
22. NOTE: Engine shown removed for clarity.
CAUTIONS:
Remove and discard the high-pressure fuel supply lines.
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
NOTE: Engine shown removed for clarity.
Page 1234 of 3039
23.
24.
25.
26. CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
CAUTION: Be prepared to collect escaping fluids.
CAUTION: Be prepared to collect escaping fluids.
Page 1235 of 3039
Installation
All vehicles
1. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with
clean engine oil.
2. CAUTION: Tighten on both sides simultaneously. Torque: 12 Nm
3. Loosen the Torx screws half a turn each. 4.
Page 1236 of 3039
5. CAUTION: Install new high-pressure fuel supply lines.
NOTES:
Engine shown removed for clarity.
Remove and discard the blanking caps.
Install the bolt and unions fully finger tight before final
tightening.
6. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.
NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.
Torque: 12 Nm
7. Lower the vehicle.
8. NOTES:
Do not tighten at this stage.
Remove and discard the blanking caps.
9. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.
Page 1237 of 3039
Raise and support the vehicle.
10.
11. CAUTION: Lubricate only the union threads with clean engine oil.
NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm
NOTE: Engine shown removed for clarity.
Torque: 21 Nm www.JagDocs.com
Page 1238 of 3039
12.
13.
14. NOTES:
Install the bolt and unions finger tight before final tightening.
Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm
Torque: 21 Nm
NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm
Page 1239 of 3039
15.
16. NOTE: Engine shown removed for clarity.
Torque: 25 Nm
Left-hand drive vehicles
17. Torque: 100 Nm
Page 1240 of 3039
18. Torque: 35 Nm
All vehicles
19. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
20. Refer to: Engine Mount RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
21. Lower the vehicle.
22.
23.
NOTES:
Lubricate
the
union
threads
with
clean
engine
oil.
Do
not tighten
at this
stage.
Remove
and
discard
the
blanking
caps.