JAGUAR XFR 2010 1.G Workshop Manual

Bolts 8 Nm










25. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

26.
27. 28.













29. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and

5.0L Petrol (501-02 Front End Body Panels, Removal and Installation).
31. Refer to: Secondary Bulkhead Panel LH - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-02 Front End Body Panels, Removal and Installation).
32. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
www.JagDocs.com

Fuel Charging and Controls - V8 S/C 5.0L Petrol - Throttle Body
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 08-Nov-2013


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. Refer to: Cooling System Partial Draining, Filling and Bleeding (303-03E,
General Procedures).

4. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

5. Refer to: Air Cleaner Outlet Pipe (303-12E, Removal and Installation).

6.

Installation
10.
















11.

























12.


















Torque: 10 Nm
























CAUTIONS:


Take extra care when removing the throttle body,
failure to follow this instruction may result in damage to
the manifold absolute pressure and temperature (MAPT)
sensor.


Do not attempt to clean the throttle body bore, build
up of deposits reduces air leakage past the throttle plate at
the fully closed position.
Remove and discard the gasket.

1. To install, reverse the removal procedure.

Accessory drive belt tensioner retaining bolt 40 30 - Accessory drive belt idler pulley retaining bolt - all vehicles 40 30 - Accessory drive belt center idler pulley retaining bolt - vehicles without supercharger 25 19 - Accessory drive belt idler pulley retaining bolt to tensioner bracket - vehicles with supercharger 40 30 - Supercharger belt tensioner bracket retaining bolt 25 19 - Supercharger belt tensioner retaining bolt 40 30 - Supercharger belt 76mm idler pulley retaining bolt 40 30 - Supercharger belt 90mm idler pulley retaining bolt 56 41 -

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive - Component Location
Description and Operation
COMPONENT LOCATION










































Item Description A Primary accessory drive B Secondary accessory drive 1 Coolant pump 2 Power steering pump 3 Primary drive belt 4 A/C (air conditioning) compressor 5 Belt tensioner 6 Crankshaft pulley/torsional vibration damper 7 Idler pulley

9 Idler pulley 10 Supercharger 11 Idler pulley 12 Belt tensioner 13 Secondary drive belt 14 Idler pulley www.JagDocs.com

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive - Overview
Description and Operation

OVERVIEW

The accessory drive is a belt system powered by a pulley attached to the front of the crankshaft. The crankshaft pulley, which
incorporates a torsional vibration damper, drives two drive belts. An automatic belt tensioner in each belt run maintains the
drive belt at the correct tension. Together with idler pulleys, the belt tensioners also guide the drive belts clear of obstructions
and set the correct 'wrap-around' of the accessory component drive pulleys to ensure a slip-free drive.

PRIMARY DRIVE BELT
The primary drive belt is a six-ribbed poly-V belt that drives the:
Coolant pump
Power steering pump
A/C (air conditioning) compressor
Generator.

SECONDARY DRIVE BELT

The secondary drive belt is an eight-ribbed poly-V belt that drives the SC (supercharger).

BELT TENSIONERS

Each belt tensioner consists of an idler pulley on the end of a spring loaded pivot arm. The pivot arms can be turned manually
for removal and installation of the drive belts.
Each belt tensioners is calibrated to automatically maintain the correct tension in the related drive belt.

Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive Belt
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger Belt (303-05, Removal and Installation).


3. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

4. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

5. Torque: 55 Nm 6. Torque: 25 Nm