JAGUAR XFR 2010 1.G Workshop Manual
Page 1461 of 3039
Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Driveshaft - TDV6 3.0L Diesel (205-01 Driveshaft, Removal and Installation).
4. Refer to: Transmission Support Insulator - TDV6 3.0L Diesel (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal and Installation).
5. CAUTION: Discard the nut.
Special Tool(s): 205-053
6. Special Tool(s): 303-D121 7. CAUTION: Discard the seal.
Special Tool(s): 100-012, 100-012-01, 308-375
Page 1462 of 3039
Installation
1. CAUTIONS:
Make sure that the mating faces are clean and free of
foreign material.
Install a new seal.
Special Tool(s): 204-264
2. WARNING: Make sure that a new nut is installed.
Torque: 60 Nm
3. Refer to: Transmission Support Insulator - TDV6 3.0L Diesel (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Driveshaft - TDV6 3.0L Diesel (205-01 Driveshaft, Removal and Installation).
5. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures). www.JagDocs.com
Page 1463 of 3039
Published: 11-May-2011
Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Transmission Control Module (TCM) and Main Control Valve
Body
Removal and Installation
Removal
NOTE: The transmission control module (TCM) is part of the main control valve body and cannot be serviced separately.
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Transmission Fluid Pan, Gasket and Filter (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, Removal and Installation).
4.
5.
Page 1464 of 3039
6. CAUTION: Discard the component.
7. CAUTION: Be prepared to collect escaping fluids.
NOTE: Note the position of the manual park brake
release.
8.
Page 1465 of 3039
9.
Installation
1. CAUTIONS:
Make sure that when fully fitted, all seals protrude by
the same amount.
Install the new seals.
Install a new seal block.
2. CAUTIONS:
Install the new seals.
Make sure that when fully fitted, all seals protrude by
the same amount.
Page 1466 of 3039
3. CAUTION: Make sure the manual park release is
correctly engaged.
Torque: 8 Nm
4. CAUTION: Make sure that a new component is
installed.
5.
Page 1467 of 3039
Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, Removal and Installation).
8. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
9. If a new component has been installed, configure using Jaguar approved
diagnostic equipment. www.JagDocs.com
Page 1468 of 3039
Published: 11-May-2011
Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Transmission Fluid Pan, Gasket and Filter
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. Raise and support the vehicle.
3. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).
4. Refer to: Transmission Fluid Drain and Refill (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, General Procedures).
5.
6. NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.
Page 1469 of 3039
Installation 7. CAUTIONS:
Make sure that the area around the component is
clean and free of foreign material.
Be prepared to collect escaping fluids.
Torque: 8 Nm
1. To install, reverse the removal procedure.
Page 1470 of 3039
Published: 11-May-2011
Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Transmission Support Insulator V8 5.0L Petrol/V8 S/C 5.0L
Petrol
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).
Installation
3. CAUTION: During this procedure the transmission
crossmember is removed, make sure the transmission is
correctly supported to avoid damaging associated
components.
Torque: 48 Nm
4. NOTE: Do not disassemble further if the component is
removed for access only.
Torque: 55 Nm
1. To install, reverse the removal procedure.