LAND ROVER FRELANDER 2 2006 Repair Manual

Publi s hed: 11-May-2011
Clutch Controls - Clutch PedalRHD AWD
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he s econdary bulkhead cent er panel.
Refer t o: Secondary Bulkhead Cent er Panel - TD4 2.2L Dies el(501-02 Front End Body Panel s, Removal and Ins tal lati on).
2.
3. CAUTION: Brake flui d wil l damage pai ntfinis hed s urfaces . If s pil led, immedi ately remove t hefluid and cl ean the area wit h wat er.
• NOTE: Pos it ion clot h t o col lect fl uid s pil lage.
3.
4. NOTE: If equiped4.
Remove t he dri ver l ower ai r bag.
Refer t o: Dri ver Lower Air Bag Module (501-20B SupplementalRes traint Sys t em, Removal and Inst all at ion).
5.

6. W ARNING: Make sure t hat a new bolt i s
i ns t alled.
T orque: 25 Nm 6.
7.
8.

9.
10.
11.

T orque:
24 Nm 12.
13. CAUTION: "Make sure t hat a new component
i s ins tal led. "
• NOTE: Do not di sas s emble furt her i f the component is
removed for acces s onl y.
13.

14.
Installation
1. CAUTION: "Make sure t hat a new component isi ns t alled. "1.
To i nst all , revers e t he removal procedure.2.
Bleed t he clut ch sys t em.
Refer t o: Clutch Sys tem Bleeding (308-00 ManualTrans mi ss ion/Transaxle and Clut ch - General Informati on, GeneralProcedures ).
3.

Publi s hed: 11-May-2011
Clutch Controls - Clutch PedalLHD AWD
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,Removal and Ins tall ati on).
2.
3. CAUTION: Brake flui d wil l damage pai ntfinis hed s urfaces . If s pil led, immedi ately remove t hefluid and cl ean the area wit h wat er.
• NOTE: Pos it ion clot h t o col lect fl uid s pil lage.
3.
4. NOTE: If equiped4.
Remove t he ins trument panel as sembl y.
Refer t o: Ins trument Panel - TD4 2.2L Dies el (501-12 Inst rumentPanel and Cons ole, Removal and Inst all at ion).
5.

6.
7.
T orque:
24 Nm 8.

9. CAUTION: "Make sure t hat a new component isi ns t alled. "
Cut t he head off the cl evi s pin to al low removal.
9.
10.
Installation
1. CAUTION: "Make sure t hat a new component isi ns t alled. "1.
To i nst all , revers e t he removal procedure.2.

Bleed t he clut ch sys t em.
Refer t o: Clutch Sys tem Bleeding (308-00 ManualTrans mi ss ion/Transaxle and Clut ch - General Informati on, GeneralProcedures ).
3.

Publi s hed: 11-May-2011
Manual Transmission/Transaxle - Transmission Draining and Filling
General Procedures W ARNING: Observe due care when drai ning, as the flui d can be very hot .
1. W ARNING: Do not work on or under a vehi cle s upported onl y
by a jack. Al ways support t he vehi cl e on s afet y s tands .
• NOTE: Make s ure that t he vehi cl e is st andi ng on a level s urface.
Rais e and s upport t he vehi cl e.
1.
Remove t he front unders hiel d.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
2.
Clean t he area around the trans mi s si on fl uid l evel /fil ler plug.
3. Remove the trans mi ss i on fl uid fil ler/level plug.
4.
Clean t he area around the trans mi s si on fl uid drain pl ug.
5.
Place a contai ner under the t rans mi ss i on.
6. Remove the trans mi ss i on fl uid drai n plug.
7.
8. CAUTION: Replace t he washer.
Inst all t he transmis si on fluid drain pl ug.
T orque: 30 Nm 8.
Fil l the t rans mi ss ion wit h t he correct fl uid unt il it runs from t he
l evel/fi ll er pl ug.
9.