LAND ROVER FRELANDER 2 2006 Repair Manual

1
2
1
SymptomPossible causesAction
Door lat chi ng andl ocking funct ion t es tDoor l at chCabl e faultDoor handleDoor l ock s wi tchW iring harnes sCent ral juncti on box (CJB)
• NOTE: Complete the diagnostic steps below to confirmany concern prior replacing the component
Check for relevant s t ored DTCsOnce any DTC relat ed fault s have been recti fi edconti nue wit h t he diagnos t ic s t eps bel owThe firs t component that s houl d be checked whenexperi encing l ocki ng or latching i s sues are t he doorl atch release cables , t hen the door lat ch. These canbe tes ted as a dis crete components to confi rm if t hes peci fi c component is working as des igned or isdemons trati ng a faul tSingle door will not open from the outside (butopens from the inside)GO t o Pi npoi nt Tes t A.Single Door Will Not Open From T he Inside (butopens from the outside)GO to Pi npoi nt Tes t B.Door Latching and Locking Function T estGO t oPi npoi nt Tes t C.No lock / unlock function from key-fobGO t oPi npoi nt Tes t E.
Latch mount ed door ajars wit ch t es tDoor l at chW iring harnes sIns trument cl ust er
Latch Mounted Door Ajar Switch T estGO t oPi npoi nt Tes t D.
Vehicle el ect ri cal s yst emt estFus esW iring harnes sW iring connect or(s)
Vehicle Electrical System T estGO t o Pi npoi nt Tes tE.Check for relevant s t ored DTCsRefer t o t he electrical ci rcuit di agrams t o locate thefaultCarry out cont inui ty t es t to confi rm circui t integrit y
DTC Index
For a li st of Di agnos ti c Trouble Codes (DTCs) t hat coul d be logged on t his vehicle, pleas e refer to Sect ion 100-00.REFER to: Di agnos ti c Trouble Code (DTC) Index - DTC: Body Cont rol Module (BCM) (100-00 General Informat ion,Des cript ion and Operat ion) /Diagnost ic Troubl e Code (DTC) Index - DTC: Dri ver/Pas s enger Door Modul e (DDM/PDM) (100-00 General Informat ion,Des cript ion and Operat ion).
Pinpoint Test
PINPOINT TEST A : SINGLE DOOR WILL NOT OPEN FROM THE OUTSIDE (BUT OPENS FROM THE
INSIDE)
T EST CO NDIT IONSDET AILS/RESULT S/ACT IONSA1: CHECK T HE EXT ERIO R DOOR RELEASE CABLE T O EXT ERIOR DOOR HANDLE IS INST ALLED CORRECT LY
Remove the door trim panel as necess ary.REFER t o: Front Door Trim Panel (501-05 Interior Tri m andOrnamentat ion, Removal and Inst all ati on) /Rear Door Tri m Panel (501-05 Int erior Tri m andOrnamentat ion, Removal and Inst all ati on).
Confirm t he exterior door releas e cabl e is correctl y ins t al ledto the ext erior door handle
Is t he cabl e correct ly i nst all ed?YesGO t o A2.NoConnect the door rel eas e cable correctl y. If the cable isdamaged, install a new door release cable. Tes t t hesys t em for normal operat ion.
A2: CHECK T HE EXT ERIO R DOOR HANDLE RELEASE CO NNECT ION T O T HE DOOR LAT CHConfirm t he exterior door handle releas e connecti on to thedoor l at ch is ins tal led correct ly

1
2
3
1
Is t he exterior door handle releas e cabl e ins t al led correct ly?YesGO t o Pinpoint Tes t C.NoConnect the door rel eas e cable correctl y. If the cable isdamaged, install a new door release cable. Tes t t hesys t em for normal operat ion.
PINPOINT TEST B : SINGLE DOOR WILL NOT OPEN FROM THE INSIDE (BUT OPENS FROM THE
OU TSIDE)
T EST CO NDIT IONSDET AILS/RESULT S/ACT IONS
B1: CHECK T HE INT ER IOR DOOR RELEASE CABLE T O INT ERIOR DOOR HANDLE IS INST ALLED CORRECT LY
• NOTE: Fi gure A - Child lock off pos it ion s hown
Make sure t he chi ld lock is di sengaged (rear door only)
Remove the door trim panel as necess aryREFER t o: Front Door Trim Panel (501-05 Interior Tri m andOrnamentat ion, Removal and Inst all ati on) /Rear Door Tri m Panel (501-05 Int erior Tri m andOrnamentat ion, Removal and Inst all ati on).Confirm t he i nt eri or door rel ease cable is correct ly ins tall edto the i nterior door handle
Is t he cabl e correct ly i nst all ed?YesGO t o B2.NoConnect the door rel eas e cable correctl y. If the cable isdamaged, install a new door release cable. Tes t t hesys t em for normal operat ionB2: CHECK T HE INT ER IOR DOOR HANDLE RELEASE CONNECT ION T O T HE DOOR LAT CH
Confirm t he i nt eri or door handl e release connect ion to t hedoor l at ch is ins tal led correct ly
Is t he i nt eri or door handl e rel ease cable ins tal led correct ly?YesGO t o Pinpoint Tes t C.NoConnect the door rel eas e cable correctl y. If the cable isdamaged, install a new door release cable. Tes t t hesys t em for normal operat ion.
PINPOINT TEST C : DOOR LATCHING AND LOCKING FUNCTION TEST

1
2
3
4
5
6
7
8
9
T EST CO NDIT IONSDET AILS/RESULT S/ACT IONS
C1: DOOR LAT CH T EST
• NOTE: Tes t as a s ingle component to ens ure that t he door l atch i s not replaced unnecess ari ly, when another componentmay be at fault
Remove door t ri m from doorREFER t o: Front Door Trim Panel (501-05 Interior Tri m andOrnamentat ion, Removal and Inst all ati on) /Rear Door Tri m Panel (501-05 Int erior Tri m andOrnamentat ion, Removal and Inst all ati on).
Remove modul e plat e / clos ing panel from door
Remove latch modul e from door REFER to: (501-14Handl es , Locks , Latches and Ent ry Sys t ems)Front Door Latch (Removal and Inst all at ion),Rear Door Lat ch (Removal and Ins t al lat ion).
Ins pect l atch module for any vis ual damage
Disconnect i nt eri or releas e bowden cabl e at door l atch
Disconnect exterior rel eas e bowden cabl e at door latch
W i th t he l at ch in hand, connect the el ect ri cal connect or(s )to connect door lat ch to door harnes s• NOTE: T HE LAT CH IS NO W READY T O T EST
Clos e all vehicle doors except the door being i nves ti gat ed
• NOTE: Fi gure 1 - Unlatched posi ti on s hown
• NOTE: Fi gure 2 - Fi rs t s afet y lat ched pos it ion s hown
• NOTE: Fi gure 3 - Ful ly l atched posi ti on s hown
• NOTE: T est w ill not work if latch is only in first safety latchposition
Rot ate lat ch cl aw (usi ng a s mall s crew driver or s imi lar) tothe full y lat ched pos it ion (Figure 3)

10
11
• NOTE: Unl ocked pos it ion s hown
Confirm t hat the latch i nterior rel eas e l ever i s in theunl ocked pos it ion as s hown
• NOTE: Locked pos i ti on s hown
Pres s the lock butt on on t he key-fob or s mart key
Does t he l at ch int eri or releas e lever move from the unlockedpos it ion to t he l ocked posi ti on?YesGO t o C2.NoIf t his i s a repeat t est and the vehicle el ect ri cal t estsect ion has been compl eted and confi rmed that vehi cl e i sworking correct ly, t hen replace t he door l atch. If replaci nglat ch as part of a warranty cl ai m, pleas e quote referencecode LKINOP in t he t echnician comment s s ect ion of t hewarrant y claimC2: T EST 1 DOOR LAT CH

1
1
• NOTE: Locked pos i ti on s hown
W i th t he l at ch in the locked s t ate (i.e. the latch i nteriorreleas e l ever is in t he l ocked posi ti on), pres s t he key-fob orsmart keyunlock but ton
Does t he l at ch int eri or releas e lever move from the l ockedpos it ion to t he unlocked pos i ti on?YesGO t o C3.NoGO t o Pinpoint Tes t E. If pinpoint t est E has beencompl eted and confi rmed t hat vehi cl e is correctl y s uppl yi ngsi gnal s t o lat ch, t hen replace t he door latch. If replacinglat ch as part of a warranty cl ai m, pleas e quote referencecode UNLKINOP in the t echnici an comment s s ect ion of t hewarrant y claim
C3: T EST 2 DOOR LAT CH
• NOTE: Ful ly l atched pos i ti on s hown
W i th t he l at ch in it s unlocked st ate, pus h the latch ext eriorreleas e l ever agains t it s ret urn s pring, whils tsi mult aneous ly applyi ng a l ight pres sure t o rel eas e t helat ch cl aw us ing a smal l screw dri ver or s imilar
Does t he l at ch claw releas e?YesGO t o C4.NoRepeat t es t s C2 and C3 to confi rm t he fault . GO t o C2. Ifthe repeat t es t has confi rmed that t he ext eri or releas elever will not rel ease the claw on an unlocked lat ch replacethe door lat ch. If replacing latch as part of a warrant ycl aim, pl eas e quote reference code EXT INOP in t hetechni cian comments secti on of the warrant y claim
C4: T EST 3 DOOR LAT CH

1
2
3
• NOTE: Ful ly l atched pos i ti on s hown
Usi ng a s mal l screw dri ver or s imi lar, rot at e l atch claw tothe s econd full y l at ched pos it ion
• NOTE: Fi gure A - Child lock off pos it ion s hown
If t est ing a rear door latch, ensure t hat t he child lock isturned to the off pos it ion
Confirm t hat the latch i nterior rel eas e l ever i s in theunl ocked pos it ion as s hown

4
1
2
3
4
W hil s t the l atch i s s ti ll in it s unlocked s t ate, push the latchint erior rel ease lever agains t it s return s pring, whil s tsi mult aneous ly applyi ng a l ight pres sure t o rel eas e t helat ch cl aw us ing a smal l screw dri ver or s imilar
Does t he l at ch claw releas eYesLat ch has pas s ed all t est s t o confirm it s correct functi on.DO NO T REPLACE LAT CH as part of any att empts t ores olve any locking funct ionalit y i ss ues . GO t o PinpointTes t E. To confirm vehi cl e electrical si gnal i s received bythe l atchNoRepeat t hi s t estGO t o C4. If repeat tes t has confirmed t hatthe i nterior rel eas e l ever wi ll not rel eas e t he claw when thelat ch is i n t he unl ocked s t at e, then replace the latch. Ifreplacing l atch as part of a warrant y claim, please quot ereference code INT INOP i n t he technician comment ssect ion of t he warrant y claim
PINPOINT TEST D : LATCH MOUNTED DOOR AJAR SWITCH TEST
T EST CO NDIT IONSDET AILS/RESULT S/ACT IONS
D1: T EST 4 DOOR LAT CH• NOTE: If a cust omer is compl ai ning of is s ues rel at ing to a door ajar si gnal e.g. door lat ch won’t lock, or al arm sys temt ri ggering (indicated vi a DTC’s ), t here may be s everal component s t hat generat e t he fault , including
Door Lat ch ajar s wit chAlarm control modul eCentral junct ion boxBody wiring harnes s / connect orsDoor wiring harnes s / connect ors
• NOTE: To i nves t igate the funct ioning of t he door ajar swi tch contai ned wit hin t he door latch, to prove or eli minate thedoor latch mount ed door ajar swi tch as the root caus e, foll ow t he proces s bel ow. This wil l prevent t he unneces saryrepl acement of a correct ly funct ioning door lat chRemove door t ri m from doorREFER t o: Front Door Trim Panel (501-05 Interior Tri m andOrnamentat ion, Removal and Inst all ati on) /Rear Door Tri m Panel (501-05 Int erior Tri m andOrnamentat ion, Removal and Inst all ati on).
Remove modul e plat e / clos ing panel from door
Remove latch modul e from door REFER to: (501-14Handl es , Locks , Latches and Ent ry Sys t ems)Front Door Latch (Removal and Inst all at ion),Rear Door Lat ch (Removal and Ins t al lat ion).
Ins pect l atch module for any vis ual damage

5
6
• NOTE: Fi gure 1 - Unlatched posi ti on s hown
• NOTE: Fi gure 2 - Fi rs t s afet y lat ched pos it ion s hown
• NOTE: Fi gure 3 - Ful ly l atched posi ti on s hown
• NOTE: Tes t wi ll not work i f lat ch is only in firs t safety l atchpos it ion
Usi ng a s mal l screw dri ver or s imi lar, rot at e l atch claw tothe s econd full y l at ched pos it ion (figure 3)
Carry out conti nui ty tes t between t ermi nals 1 and 4 (leftside) or 8 and 4 (right side) wi th cl aw clos ed
Does t he conti nui ty t es t pas s ?YesThe lat ch ajar swit ch is worki ng correct ly. Do not replacelatch. Inves t igate for fault el s ewhere in vehi cl e s ys t emNoRel ease latch cl aw and repeat tes t from st ep 5 to confi rmres ult . If t his i s a repeat t est and you are s ure t hat theajar s wit ch does not provi de cont inuit y when ful ly l atched.Repl ace the l atch. If repl aci ng lat ch as part of a warrantycl aim, pl eas e quote reference code AJARINOP i n t hetechni cian comments secti on of the warrant y claim
PINPOINT TEST E : VEHICLE ELECTRICAL SYSTEM TEST
T EST CO NDIT IONSDET AILS/RESULT S/ACT IONS
E1: T EST 5 LOCK COMMAND

1
2
3
1
Dis connect el ect ri cal connect or from lat ch
Clos e all vehicle doors apart from door bei ng inves ti gat ed,please not e whi ch door, left s i de or ri ght s ide is underinvest igat ion
Moni tor t he circui t for moment ary power when locki ng t hevehi cl e via t he key-fob or smart key between t ermi nal s 1and 10 left side or 8 and 10 right side
Is t here moment ary power (for approx 8 seconds ) betweenterminals 1 and 10 left side or 8 and 10 right side whenlocki ng the vehicle via t he key-fob or s mart keyYesThe vehi cl e electrical sys tem is locki ng correct ly, providingthe s i gnal t o t he lat ch. GO to E2.NoRefer to the el ect ri cal circui t diagrams and i nves t igate whyvehi cl e electrical sys tem is not provi ding s ignals to t helat ch. Us ing t he manufacturer approved di agnos ti c s ys t emcheck for l ogged DTCs t o l ocali ze t he faultE2: T EST 6 UNLO CK COMMAND
Moni tor t he circui t for moment ary power when unl ocki ng thevehi cl e via t he key-fob or smart key between t ermi nal s 1and 9 left side or 8 and 9 right side
Is t here moment ary power (for approx 8 seconds ) betweenterminals 1 and 9 left side and 8 and 9 right side whenunl ocking t he vehicle vi a t he key-fob or s mart keyYesThe vehi cl e electrical sys tem is unl ocking correctl y,providing t he s ignal to the l atch. Plug elect rical connectorback i n t o lat ch. Rebuil d vehi cl e and check for correctoperati onNoRefer to the el ect ri cal circui t diagrams and i nves t igate whyvehi cl e electrical sys tem is not provi ding s ignals to t helat ch. Us ing t he manufacturer approved di agnos ti c s ys t emcheck for l ogged DTCs t o l ocali ze t he fault

Publi s hed: 11-May-2011
Handles, Locks, Latches and Entry Systems - Liftgate Striker Adjustment
General Procedures
Check for an equal gap and al ignment to the adjacentpanel s . If i ncorrect , fol low the adjus t procedure below.1.
Remove t he s pare wheel cover.2.
Remove t he loadspace s cuff plat e.3.
Loos en t he 2 l iftgate s triker bol ts .4.