LEXUS RC350 2023 Owner's Manual

20
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Wiper intervals can be adjusted when inter-
mittent operation is selected.
5Increases the intermittent windshield
wiper frequency
6Decreases the intermittent windshield
wiper frequency
7 Washer/wiper dual operation
Pulling the lever operates the wipers
and washer.
The wipers will automatically operate a
couple of times after the washer
squirts.
Vehicles with headlight cleaners:
When the engine switch is in IGNI-
TION ON mode and the headlights
are on, if the lever is pulled, the head-
light cleaners will operate once. After
this, the headlight cl eaners will operate
every 5th time the lever is pulled.
 Rain-sensing windshield wipers
1 (U.S.A.) or (Canada)
Move the lever up by 2 levels
2 Move the lever up by 1 level
3 (U.S.A.) or (Canada)
Move the lever down by 1 level
4 (U.S.A.) or (Canada)
Move the lever down by 2 levels
5 AUTO mode on/off switch
The AUTO mode indicator will turn
on when AUTO mode is selected.
A

21
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Depending on the operating state of the wipers when the wiper lever is operated, the wipers
will operate as follows.
• Current wiper operation: Off
• Current wiper operation: Low speed operation
• Current wiper operation: High speed operation
• Current wiper operation: AUTO mode (Intermittent operation)
Wiper lever operationWiper operation
or Temporary operation
Temporary operation
or Low speed operation
or High speed operation
Wiper lever operationWiper operation
or Off
Off
or High speed operation
or High speed operation
Wiper lever operationWiper operation
or Off
Low speed operation
or No change
or No change
Wiper lever operationWiper operation
or Off
Temporary operation*1
or Low speed operation*2
or High speed operation*2

22
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
• Current wiper operation: AUTO mode (Continuously)
*1: After temporary operation, the mode will return to AUTO mode.
*2: AUTO mode will be canceled.When AUTO mode is selected, the sensor
sensitivity can be adjusted by turning the
switch ring.
6Increases the sensitivity
7Decreases the sensitivity
8 Washer/wiper dual operation
Pulling the lever operates the wipers
and washer.
The wipers will automatically operate a
couple of times after the washer
squirts.
Vehicles with headlight cleaners:
When the engine switch is in IGNI-
TION ON mode and the headlights
are on, if the lever is pulled, the head-
light cleaners will operate once. After
this, the headlight cl eaners will operate
every 5th time the lever is pulled.
Wiper lever operationWiper operation
or Off
No change
or Low speed operation*2
or High speed operation*2

23
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Turns the intuitive parking assist on/off
When on, the indicator light comes on to
inform the driver that the system is opera-
tional.
Intuitive Parking Assist (if equipped)
The distance from your vehicle to nearby obstacles when parallel parking or maneuvering
into a garage is measured by the sensors and communicated via the multi-information dis-
play, Center Display and a buzzer. Always check the surrounding area when using this
system.
Intuitive parking assist switch

24
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
BSM main switch
This switch is for both the BSM function
and RCTA function.
Pressing the switch turns the system on
or off. When the switch is turned on,
the indicator on the switch illuminates.
Outside rear view mirror indicators
BSM function:
When a vehicle is detected in a blind
spot of the outside rear view mirrors or
approaching rapidly from behind into a
blind spot, the outside rear view mirror
indicator on the detected side will illu-
minate. If the turn signal lever is oper-
ated toward the detected side, the
outside rear view mirror indicator will
flash.
RCTA function:
When a vehicle approaching from the
right or left at the rear of the vehicle is
detected, both outside rear view mirror
indicators will flash.
Center Display
If a vehicle approaching from the right or left at the rear of the vehicle is detected, the
RCTA icon for the detected side will be displayed on the Center Display.
This illustration shows an example of a vehi cle approaching from both sides of the vehi-
cle.
RCTA buzzer (RCTA function only)
If a vehicle approaching from the right or left at the rear of the vehicle is detected, a
buzzer will sound. The buzzer also sounds for approximately 1 second immediately
after the BSM main switch is op erated to turn the system on.
BSM (Blind Spot Monitor)
The Blind Spot Monitor is a system that has 2 functions:
● The BSM (Blind Spot Monitor) function
Assists the driver in making a decision when changing lanes
● The RCTA (Rear Cross Traffic Alert) function
Assists the driver when backing up
These functions use same sensors.
A
B
C
D

25
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
The tire pressure detected by the tire pres-
sure warning system can be displayed on
the multi-information display.
The illustration used is intended as an exam-
ple, and may differ from the image that is
actually displayed on the multi-information
display.
1Park the vehicle in a safe place, turn the engine switch off and wait 20 minutes or more.
Initialization cannot be performe d while the vehicle is moving.
2Adjust the tire inflation pressure to the sp ecified cold tire inflation pressure level.
Make sure to adjust the tire pressure to the specified cold tire inflation pressure level.
The tire pressure warning system will operate based on this pressure level.
3Start the engine.
4Press and hold the tire pressure warn-
ing reset switch until the tire pressure
warning light blinks slowly 3 times.
Then a message will be displayed on
the multi-information display.
5Drive straight (with occasional left and righ t turns) at approximately 25 mph (40 km/h)
or more for approximat ely 10 to 30 minutes.
Initialization is complete when the position of each tire is determined and the inflation
pressure of each tire is displayed on the multi-information display.
Tire Pressure Warning System
Your vehicle is equipped with a tire pressure warning system that uses tire pressure warn-
ing valves and transmitters to detect low tire inflation pressure before serious problems
arise.
The tire inflation pressure display function
Initializing the tire pressure warning system

26
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
1Louder
2Lower
The indicator comes on when the ASC sys-
tem is on.
When the dial is turned to the lowest vol-
ume, the ASC system will be turned off and
the indicator will go off.
ASC (Active Sound Control) (if equipped)
The ASC system is an electronic sound syst em that generates engine sound, conveying
the kinetic situations of the vehicle’s acceler ation and deceleration to the driver through
the speakers inside the instrument panel.
The vehicle’s response to the driver’s acceler ation behavior and shift operations are also
conveyed in sound.
When sport mode is selected, the sound conveyed to the driver will be louder.
Controlling volume

27
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Driving Comfort
Vehicles with a 10.3-inch display
“MAP” button
Press this button to display the vehicle’s
current position.
“MENU” button
Press this button to display the menu
screen.
Back button
Press this button to display the previ-
ous screen.
Touchpad
Slide your finger on the touchpad and move the pointer to select a function, letter and
screen button.
Press the touchpad to enter the selected function, letter or screen button. Certain fin-
ger movements on the touchpad can perform functions, such as changing map scalings
and scrolling list screens.
Sub function button
When is displayed on the screen, a functi on screen assigned to the screen can be
displayed.
Remote Touch
The Remote Touch can be used to operate the Center Display.
Remote Touch is the name for the device that includes the “MAP” button, “HOME” but-
ton, “MENU” button, back button, touchpad and sub function button.
Names and operations of each part
A
B
C
D
E

28
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Vehicles with a 8-inch display
“HOME” button
Press this button to display the “Home”
screen.
“MENU” button
Press this button to display the menu
screen.
Back button
Press this button to display the previ-
ous screen.
Touchpad
Slide your finger on the touchpad and move the pointer to select a function, letter and
screen button.
Press the touchpad to enter the selected function, letter or screen button. Certain fin-
ger movements on the touchpad can perform functions, such as scrolling list screens.
Sub function button
When is displayed on the screen, a functi on screen assigned to the screen can be
displayed.
A
B
C
D
E

29
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Press the “MENU” button on the Remote Touch to display the menu screen.
*1: Refer to the “NAVIGATION AND MU LTIMEDIA SYSTEM OWNER’S MANUAL”.
*2: This function is not available on some models.
Center Display
Menu screen
Vehicles with a 10.3-inch display Vehicles with a 8-inch display
SwitchFunction
Select to display the “Destination” screen. ( P.34)
Select to display the audio control screen. (P.43, 44, 45, 46)
Select to display the hands-free control screen. ( P.37)
Select to display the “Apps” screen.*1, 2
//
When an Apple CarPlay/Android Auto connection is established
and this button displays “Apple CarPlay”/“Android Auto”, select to
display the Apple CarPlay/Android Auto screen.
*1, 2
Select to display th e information screen. (P.32)
Select to display the setup screen.*1
Select to display the air co nditioning control screen. ( P.48)
Select to adjust the contrast and brightness of the screens, turn the
screen off, etc.
*1, 2