LEXUS SC400 1991 Service Repair Manual

FLOOR CARPET
COMPONENTS
BO±116±
BODY Floor Carpet
WhereEverybodyKnowsYourName

REMOVAL OF FLOOR CARPET
1. REMOVE FOLLOWING PARTS:
wFront seat (See step 3 on page BO±58)
wRear seat (See steps 1 to 2 on page BO±66)
wRoof side inner garnish (See step 8 on page BO±123)
wFront pillar garnish (See step 2 on page BO±122)
wFront scuff plate (See step 11 on page BO±123)
wConsole box (See step 14 on page BO±111)
2. REMOVE FLOOR CARPET (a) Using a clip remover, remove the clips.
(b) Remove the front seat belt lower bolt.
[Driver 's Side]
(c) Raise the end of the carpet and disconnect the hook.
[Passenger 's Side]
(d) Raise the end of the carpet and disconnect the hook.
(e) Slide the carpet backward and remove it.
±
BODY Floor CarpetBO±117
WhereEverybodyKnowsYourName

INSTALLATION OF FLOOR CARPET
(See page BO±117)
INSTALL FLOOR CARPET PARTS BY FOLLOWING REMOVAL
SEQUENCE IN REVERSE HINT: Torque following parts.
(a) Front seat belt lower anchor bolt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(b) Front Seat
Torque: 37 N Vm (375 kgf Vcm, 27 ft Vlbf)
BO±118±
BODY Floor Carpet
WhereEverybodyKnowsYourName

ROOF HEADLINING
COMPONENTS
±
BODY Roof HeadliningBO±119
WhereEverybodyKnowsYourName

REMOVAL OF ROOF HEADLINING
(See page BO±119)
1. REMOVE FOLLOWING PARTS:
wFront pillar garnish
wSun visor
wRear seat back and cushion
wRoof side inner garnish
wQuarter trim
wInterior Light
wCenter visor
2. REMOVE ROOF HEADLINING (a) Disconnect four clips from the roof panel rear end.
(b) Using a clip remover, remove six clips.
(c) R e l e a s e t h e f a s t ener tapes, then remove the
headlining.
(d) Fully recline the front seat back.
(e) Bring out the headlining as shown.
NOTICE: Do not fold down the headlining.
INSTALLATION OF ROOF HEADLINING
(See page BO±119)
INSTALL ROOF HEADLINING PARTS BY FOLLOWING RE-
MOVAL SEQUENCE IN REVERSE HINT: Torque following parts:
(a) Rear seat back
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(b) Rear seat belt inner belt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(c) Front seat belt shoulder anchor bolt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
BO±120±
BODY Roof Headlining
WhereEverybodyKnowsYourName

TRIM, ASSIST GRIP AND VISOR
COMPONENTS
B06803
±
BODY Trim, Assist Grip and VisorBO±121
WhereEverybodyKnowsYourName

REMOVAL OF TRIM, ASSIST GRIP AND
VISOR
(See page BO±121)
1. REMOVE ASSIST GRIP (a) Lift up the grip so that the screwdriver can be inserted.
(b) Insert the screwdriver into the groove in the cushion.
(c) Turn the screwdriver while pulling the assist grip upward.
(d) After the top of the assist grip is freed, pull the lower part
downward.
2. REMOVE FRONT PILLAR GARNISH (a) Remove two screws and the assist grip.
(b) Pry out clips by your hand.
(c) Pull the garnish upward to remove it.
3. REMOVE SUN VISOR (a) Pry out the cover.
(b) Remove two screws, disconnect the connector and thesun visor.
(c) Remove the screw and the holder.
4. REMOVE CENTER VISOR (a) Pry out the cover.
(b) Remove two screws, disconnect the connector and thevisor.
5. REMOVE REAR SEAT CUSHION AND BACK
6. REMOVE FRONT SEAT OUTER BELT
7. REMOVE QUARTER TRIM AND ASSIST GRIP (a) Remove two caps, two screws and assist grip.
(b) Remove the clip and the belt guide.
(c) Remove the bolt and the front seat belt anchor.
BO±122
±
BODY Trim, Assist Grip and Visor
WhereEverybodyKnowsYourName

(d) Using a clip remover, remove three clips.
(e) Insert a screwdriver between the retainers and quartertrim to pry it loose.
(f) Remove the quarter trim.
8. REMOVE ROOF SIDE INNER GARNISH (a) Remove four screws.
(b) Insert a screwdriver between the retainers and innergarnish to pry it loose.
(c) Remove the inner garnish.
9. REMOVE PACKAGE TRAY TRIM (a) Using a clip remover, remove two clips.
(b) Pull the belt guide forward to remove it.
(c) Pull the trim forward to remove it.
10. REMOVE ROOM PARTITION TRIM
11. REMOVE FRONT SCUFF PLATE Using a screwdriver, remove the plate.
HINT: Tape the screwdriver tip before use.
12. REMOVE OUTSIDE SCUFF PLATE Insert a screwdriver between the retainers and the plate to
pry it loose.
HINT: Tape the screwdriver tip before use.
±
BODY Trim, Assist Grip and VisorBO±123
WhereEverybodyKnowsYourName

13. (w/ Sliding Roof)REMOVE SUN SHADE TRIM
(See steps 1 to 10 on pages BO±85 to 86)
INSTALLATION OF TRIM, ASSIST GRIP
AND VISOR
(See page BO±121)
1. (w/ Sliding Roof) INSTALL SUN SHADE TRIM
2. INSTALL OUTSIDE SCUFF PLATE Place the plate on the body and install it by tapping.
3. INSTALL FRONT SCUFF PLATE Place the plate on the body and install it by tapping.
4. INSTALL ROOM PARTITION TRIM Install the trim as shown.
5. INSTALL PACKAGE TRAY TRIM (a) Align the six retainers with the holes of the panel, thenpush the trim backward.
(b) Install two clips.
(c) Install the belt guide to the trim.
BO±124
±
BODY Trim, Assist Grip and Visor
WhereEverybodyKnowsYourName

6. INSTALL ROOF SIDE INNER GARNISH(a) Place the inner garnish on the quarter panel and installit by tapping it in.
(b) Install four screws.
7. INSTALL QUARTER TRIM AND ASSIST GRIP (a) Place the trim on the quarter panel and install it bytapping it in.
(b) Install the belt guide with the clip.
(c) Install the front seat belt anchor with the bolt.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(d) Install the assist grip with two screws and two caps.
8. INSTALL REAR SEAT CUSHION AND BACK (See page BO±67)
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
9. INSTALL CENTER VISOR
(a) Connect the connector.
(b) Install the visor with two screws and the cover.
10. INSTALL SUN VISOR (a) Install the holder with the screw.
(b) Install the sun visor with two screws and the cover.
±
BODY Trim, Assist Grip and VisorBO±125
WhereEverybodyKnowsYourName