MITSUBISHI ENDEAVOR 2004 Service Repair Manual
Page 3501 of 3870
Fig. 231: Actuator Test Specifications
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CHECK AT ABS-ECU TERMINAL VOLTAGE CHECK CHART
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3502 of 3870
Required Special Tool
:
MB991952: ABS Check Harness
1. Disconnect the ABS-ECU connector A-32, and then use special tool
MB991952 to measure the voltages between terminals (34) and each terminal
other than terminal (12) as well as between terminal (12) and each terminal
other than terminal (34).
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3503 of 3870
Fig. 232: Disconnecting ABS
-ECU Connector A
-32
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3504 of 3870
2. The terminal layouts are shown in the illustrations below.
Fig. 233: Signal Specification
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
RESISTANCE AND CONTINUITY BETWEEN HARNESS-SIDE CONNECTOR TERMINALS 1. Disconnect the connector A-32, and connect special tool ABS Check Harness
(MB991952) to the wiring harness-side connector.
2. Measure the resistance and continuity between the terminals indicated in the
table below. NOTE: Do not measure terminal voltage for approximately
three seconds after the ignition switch is turned "ON."
The TCL/ASC-ECU performs the initial check during
that period.
NOTE: Do not connect special tool ABS Check Harness
(MB991952) to the TCL/ASC-ECU.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3505 of 3870
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3506 of 3870
Fig. 234: Measuring Resistance And Continuity Between Terminals
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 235: Signal Specification
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SPECIAL TOOLS
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3507 of 3870
Fig. 236: Identifying Special Tools (1 Of 2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3508 of 3870
Fig. 237: Identifying Special Tools (2 Of 2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE WHEEL SPEED SENSOR OUTPUT VOLTAGE MEASUREMENT Required Special Tool:
MB991219: Inspection Harness
1. Release the parking brake and lift up the vehicle.
2. Disconnect the TCL/ASC-ECU connector A-32, and then use special tool
MB991219 to measure the out
put volta
ge at the harness side connector.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3509 of 3870
Fig. 238: Terminal Specification
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3510 of 3870
Fig. 239: Disconnecting TCL/ASC
-ECU Connector A
-32
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor