lock MITSUBISHI MONTERO 1998 Service Manual

Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally









\









\









\









\









\









\









\







AIR CONDITIONING & HEAT
AIR CONDITIONING TROUBLE SHOOTING
WARNING: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC AIR CONDITIONING TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE








\









\









\









\









\









\









\







Compressor Not Working
Compressor clutch circuit open.

Compressor clutch coil inoperative.

Poor clutch ground connection.

Fan belts loose.

Thermostatic switch inoperative.

Thermostatic switch not adjusted.

Ambient temperature switch open.

Superheat fuse blown.








\









\









\









\









\









\









\







Excessive Noise or Vibration
Missing or loose mounting bolts.

Bad idler pulley bearings.

Fan belts not tightened correctly.

Compressor clutch contacting body.

Excessive system pressure.

Compressor oil level low.

Damaged clutch bearings.

Damaged reed valves.

Damaged compressor.








\









\









\









\









\









\









\







Insufficient or No Cooling;
Compressor Working
Expansion valve inoperative.

Heater control valve stuck open.

Low system pressure.

Blocked condenser fins.

Blocked evaporator fins.

Vacuum system leak.

Vacuum motors inoperative.

Control cables improperly adjusted.

Restricted air inlet.

Mode doors binding.

Blower motor inoperative.

Temperature above system capacity.








\









\









\









\









\









\









\







HEATER SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to

problem symptoms. For model-specific Trouble Shooting,
refer to DIAGNOSTIC, or TESTING articles available in the
section(s) you are accessing.
BASIC HEATER SYSTEM TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE








\









\









\









\









\









\









\







Insufficient, Erratic,
or No Heat
Low Coolant Level

Incorrect thermostat.

Restricted coolant flow through
heater core.


Heater hoses plugged.

Misadjusted control cable.

Sticking heater control valve.

Vacuum hose leaking.

Vacuum hose blocked.

Vacuum motors inoperative.

Blocked air inlet.

Inoperative heater blower motor.

Oil residue on heater core fins.

Dirt on heater core fins.








\









\









\









\









\









\









\







Too Much Heat
Improperly adjusted cables.

Sticking heater control valve.

No vacuum to heater control valve.

Temperature door stuck open.








\









\









\









\









\









\









\







Air Flow Changes During
Acceleration
Vacuum system leak.

Bad check valve or reservoir.








\









\









\









\









\









\









\







Air From Defroster At All
Times
Vacuum system leak.

Improperly adjusted control cables.

Inoperative vacuum motor.








\









\









\









\









\









\









\







Blower Does Not Operate
Correctly
Blown fuse.

Blower motor windings open.

Resistors burned out.

Motor ground connection loose.

Wiring harness connections loose.

Blower motor switch inoperative.

Blower relay inoperative.

Fan binding or foreign object
in housing.


Fan blades broken or bent.








\









\









\









\









\









\









\







BRAKES
BRAKE SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.

in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Lopes At Intake manifold-to-head Replace manifold
Idle leaks gasket, See ENGINES
Blown head gasket Replace head gasket,
See ENGINES
Worn timing gears, chain Replace gears, chain or
or sprocket sprocket
Worn camshaft lobes Replace camshaft, See
ENGINES
Overheated engine Check cooling system,
See COOLING
Blocked crankcase vent Remove restriction
valve
Leaking EGR valve Repair leak and/or
replace valve
Faulty fuel pump Replace fuel pump









\









\









\









\









\









\









\







Engine Has Low Leaking fuel pump Repair leak and/or
Power replace fuel pump
Excessive piston-to-bore Install larger pistons,
clearance See ENGINES
Sticking valves or weak Check valve train
valve springs components, See ENGINES
Incorrect valve timing Reset valve timing, See
ENGINES
Worn camshaft lobes Replace camshaft, See
ENGINES
Blown head gasket Replace head gasket.
See ENGINES.
Clutch slipping Adjust pedal and/or
replace components, See
ENGINES
Engine overheating Check cooling system,
See COOLING
Auto. Trans. pressure
regulator valve faulty Replace pressure
regulator valve
Auto. Trans. fluid level Add fluid as necessary
too low
Improper vacuum diverter
valve operation Replace vacuum diverter
valve
Vacuum leaks Inspect vacuum system
and repair as required
Leaking piston rings Replace piston rings,
See ENGINES









\









\









\









\









\









\









\







Faulty High Low fuel pump volume Replace fuel pump
Speed Operation
Leaking valves or worn Replace valves and/or
springs, See ENGINES
Incorrect valve timing Reset valve timing,See
ENGINES
Intake manifold restricted Remove restriction
Worn distributor shaft Replace distributor









\









\









\









\









\









\









\







Faulty Improper fuel pump stroke Remove pump and reset
Acceleration pump stroke

Incorrect ignition timing Reset ignition timing,
See TUNE-UP
Leaking valves Replace valves, See
ENGINES
Worn fuel pump diaphragm Replace diaphragm or
or piston piston









\









\









\









\









\









\









\







Intake Backfire Improper ignition timing Reset ignition timing,
See TUNE-UP
Faulty accelerator pump Replace accelerator
discharge pump
Improper choke operation Check choke and adjust
as required
Defective EGR valve Replace EGR valve
Fuel mixture too lean Reset air/fuel mixture,
See TUNE-UP
Choke valve initial Reset choke valve
clearance too large initial clearance









\









\









\









\









\









\









\







Exhaust Backfire Vacuum leak Inspect and repair
vacuum system
Faulty vacuum diverter Replace vacuum diverter
valve valve
Faulty choke operation Check choke and adjust
as required
Exhaust system leak repair exhaust system
leak









\









\









\









\









\









\









\







Engine Ignition timing too far Reset ignition timing,
Detonation advanced See TUNE-UP
Faulty ignition system Check ignition timing,
See TUNE-UP
Spark plugs loose or Retighten or replace
faulty plugs
Fuel delivery system Inspect lines, pump and
clogged filter for clog
EGR valve inoperative Replace EGR valve
PCV system inoperative Inspect and/or replace
hoses or valve
Vacuum leaks Check vacuum system and
repair leaks
Excessive combustion
chamber deposits Remove built-up
deposits
Leaking, sticking or Inspect and/or replace
broken valves valves









\









\









\









\









\









\









\







External Oil Fuel pump improperly seated Remove pump, replace
Leakage or worn gasket gasket and seat
properly
Oil pan gasket broken or Straighten pan and
pan bent replace gasket
Timing chain cover gasket Replace timing chain
broken cover gasket
Rear main oil seal worn Replace rear main oil
seal
Oil pan drain plug not Remove and reinstall
seated properly drain plug
Camshaft bearing drain Remove restriction
hole blocked
Oil pressure sending Remove and reinstall
switch leaking sending switch









\









\









\









\









\









\









\

Excessive Oil Worn valve stems or guides Replace stems or
Consumption guides, See ENGINES
Valve "O" ring seals Replace "O" ring seals,
damaged See ENGINES
Plugged oil drain back holes Remove restrictions
Improper PCV valve Replace PCV valve
operation
Engine oil level too high Remove excess oil
Engine oil too thin Replace thicker oil
Valve stem oil deflectors Replace oil deflectors
damaged
Incorrect piston rings Replace piston rings,
See ENGINES
Piston ring gaps not Reinstall piston rings,
staggered See ENGINES
Insufficient piston ring Replace rings, See
tension ENGINES
Piston ring grooves or oil Replace piston rings,
return slots clogged See ENGINES
Piston rings sticking in Replace piston rings,
grooves See ENGINES
Piston ring grooves Replace piston and
excessively worn rings, See ENGINES
Compression rings installed Replace compression
upside down rings correctly, See
ENGINES
Worn or scored cylinder Rebore cylinders or
walls replace block
Mismatched oil ring Replace oil ring
expander and rail expander and rail, See
ENGINES
Intake gasket dowels too Replace intake gasket
long dowels
Excessive main or connecting Replace main or
rod bearing clearance connecting rod
bearings, See ENGINES









\









\









\









\









\









\









\







No Oil Pressure Low oil level Add oil to proper level
Oil pressure sender or Replace sender or gauge
gauge broken
Oil pump malfunction Remove and overhaul oil
pump, See ENGINES
Oil pressure relief valve Remove and reinstall
sticking valve
Oil pump passages blocked Overhaul oil pump, See
ENGINES
Oil pickup screen or tube remove restriction
blocked
Loose oil inlet tube Tighten oil inlet tube
Loose camshaft bearings Replace camshaft
bearings, See ENGINES
Internal leakage at oil Replace block or
passages cylinder head









\









\









\









\









\









\









\







Low Oil Pressure Low engine oil level Add oil to proper level
Engine oil too thin Remove and replace with
thicker oil
Excessive oil pump Reduce oil pump
clearance clearance, See ENGINES
Oil pickup tube or screen Remove restrictions
blocked
Main, rod or cam bearing Replace bearing to
clearance excessive reduce clearance, See

ENGINES








\









\









\









\









\









\









\







High Oil Improper grade of oil Replace with proper oil
Pressure Oil pressure relief valve Eliminate binding
stuck closed
Oil pressure sender or Replace sender or gauge
gauge faulty









\









\









\









\









\









\









\







Noisy Main Inadequate oil supply Check oil delivery to
Bearings main bearings
Excessive main bearing Replace main bearings,
clearance See ENGINES
Excessive crankshaft end Replace crankshaft, See
play ENGINES
Loose flywheel or torque Tighten attaching bolts
converter
Loose or damaged vibration Tighten or replace
damper vibration damper
Crankshaft journals Re-grind crankshaft
out-of-round journals
Excessive belt tension Loosen belt tension









\









\









\









\









\









\









\







Noisy Connecting Excessive bearing clearance Replace bearing, See
Rods or missing bearing ENGINES
Crankshaft rod journal Re-grind crankshaft
out-of-round journal
Misaligned connecting rod Remove rod or cap and
or cap realign
Incorrectly tightened rod Remove and re-tighten
bolts rod bolts









\









\









\









\









\









\









\







Noisy Pistons Excessive piston-to-bore Install larger pistons,
and Rings clearance See ENGINES
Bore tapered or out-of-round Rebore block
Piston ring broken Replace piston rings,
See ENGINES
Piston pin loose or seized Replace piston pin, See
ENGINES
Connecting rods misaligned Realign connecting rods
Ring side clearance too Replace with larger or
loose or tight smaller rings
Carbon build-up on piston Remove carbon









\









\









\









\









\









\









\







Noisy Valve Worn or bent push rods Replace push rods, See
Train ENGINES
Worn rocker arms or bridged Replace push rods, See
pivots ENGINES
Dirt or chips in valve Remove lifters and
lifters remove dirt/chips
Excessive valve lifter Replace valve lifters,
leak-down See ENGINES
Valve lifter face worn Replace valve lifters,
See ENGINES
Broken or cocked valve replace or reposition
springs springs
Too much valve stem-to-guide Replace valve guides,
clearance See ENGINES
Valve bent Replace valve, See
ENGINES
Loose rocker arms Retighten rocker arms,
See ENGINES
Excessive valve seat Reface valve seats, See
run-out ENGINES

Missing valve lock Install new valve lock
Excessively worn camshaft Replace camshaft, See
lobes ENGINES
Plugged valve lifter oil Eliminate restriction
holes or replace lifter
Faulty valve lifter check Replace lifter check
ball ball, See ENGINES
Rocker arm nut installed Remove and reinstall
upside down correctly
Valve lifter incorrect for Remove and replace
engine valve lifters
Faulty push rod seat or Replace plunger or push
lifter plunger rod









\









\









\









\









\









\









\







Noisy Valves Improper valve lash Re-adjust valve lash,
See ENGINES
Worn or dirty valve lifters Clean and/or replace
lifters
Worn valve guides Replace valve guides,
See ENGINES
Excessive valve seat or Reface seats or valve
face run-out face
Worn camshaft lobes Replace camshaft, See
ENGINES
Loose rocker arm studs Re-tighten rocker arm
studs, See ENGINES
Bent push rods Replace push rods, See
ENGINES
Broken valve springs Replace valve springs,
See ENGINES









\









\









\









\









\









\









\







Burned,Sticking Weak valve springs or Replace valves and/or
or Broken Valves warped valves springs, See ENGINES
Improper lifter clearance Re-adjust clearance or
replace lifters
Worn guides or improper Replace valve guides,
guide clearance See ENGINES
Out-of-round valve seats Re-grind valve seats
or improper seat width
Gum deposits on valve Remove deposits
stems, seats or guides
Improper spark timing Re-adjust spark timing









\









\









\









\









\









\









\







Broken Undersize pistons Replace with larger
Pistons/Rings pistons, See ENGINES
Wrong piston rings Replace with correct
rings, See ENGINES
Out-of-round cylinder bore Re-bore cylinder bore
Improper connecting rod Remove and realign
alignment connecting rods
Excessively worn ring Replace pistons, See
grooves ENGINES
Improperly assembled Re-assemble pin-to
piston pins -piston, See ENGINES
Insufficient ring gap Install new rings, See
clearance ENGINES
Engine overheating Check cooling system
Incorrect ignition timing Re-adjust ignition
timing, See TUNE-UP









\









\









\









\









\









\









\







Excessive Leaks at manifold to Replace manifold or
Exhaust Noise head, or to pipe pipe gasket
Exhaust manifold Replace exhaust

incorrect index, see FUEL
SYSTEMS
Hot fast idle RPM too low Reset fast idle RPM,
see TUNE-UP









\









\









\









\









\









\









\







BASIC HOT START SYMPTOMS TROUBLE SHOOTING CHART








\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Won't Engine flooded Allow fuel to
Start evaporate









\









\









\









\









\









\









\







BASIC COLD ENGINE DRIVEABILITY SYMPTOMS TROUBLE SHOOTING CHART








\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Stalls in Choke vacuum kick setting Reset choke vacuum
Gear incorrect kick, see FUEL
SYSTEMS
Fast idle RPM incorrect Reset fast idle RPM,
see TUNE-UP
Fast idle cam index Reset fast idle cam
incorrect see FUEL SYSTEMS









\









\









\









\









\









\









\







Acceleration Sag Defective choke control Replace choke
or Stall switch control switch
Choke vacuum kick setting Reset choke vacuum
incorrect kick see, FUEL
SYSTEMS
Float level incorrect Adjust float level,
(too low) FUEL SYSTEMS
Accelerator pump defective Repair or replace
pump see FUEL
SYSTEMS
Secondary throttles not Inspect lockout
closed adjustment,see FUEL
SYSTEMS









\









\









\









\









\









\









\







Sag or Stall Defective choke control Replace choke
After Warmup switch control switch, see
FUEL SYSTEMS
Defective accelerator pump Replace pump, see
FUEL SYSTEMS
Float level incorrect Adjust float level,
(too low) see FUEL SYSTEMS









\









\









\









\









\









\









\







Backfiring & Plugged heat crossover Remove restriction
Black Smoke system









\









\









\









\









\









\









\







BASIC WARM ENGINE DRIVEABILITY SYMPTOMS TROUBLE SHOOTING CHART








\









\









\









\









\









\









\

batteries
Bad starter connections Check connections
or bad starter and/or replace
batteries









\









\









\









\









\









\









\







Engine Cranks Bad battery connections Check connections
Slowly, Won't or dead batteries and/or replace
Start batteries
Engine oil too heavy Replace engine oil









\









\









\









\









\









\









\







Engine Cranks Glow plugs not functioning Check glow plug system,
Normally, But see FUEL SYSTEMS
Will Not Start Glow plug control not Check controller, see
functioning FUEL SYSTEMS
Fuel not injected into Check fuel injectors,
cylinders see FUEL SYSTEMS
No fuel to injection pump Check fuel delivery
system
Fuel filter blocked Replace fuel filter
Fuel tank filter blocked Replace fuel tank
filter
Fuel pump not operating Check pump operation
and/or replace pump
Fuel return system blocked Inspect system and
remove restriction
No voltage to fuel solenoid Check solenoid and
connections
Incorrect or contaminated Replace fuel
fuel
Incorrect injection pump Re-adjust pump timing,
timing see FUEL SYSTEMS
Low compression Check valves, pistons,
rings, see ENGINES
Injection pump malfunction Inspect and/or replace
injection pump









\









\









\









\









\









\









\







Engine Starts, Incorrect slow idle Reset idle adjustment,
Won't Idle adjustment see TUNE-UP
Fast idle solenoid Check solenoid and
malfunctioning connections
Fuel return system blocked Check system and remove
restrictions
Glow plugs go off too soon See glow plug diagnosis
in FUEL SYSTEMS
Injection pump timing Reset pump timing, see
incorrect FUEL SYSTEMS
No fuel to injection pump Check fuel delivery
system
Incorrect or contaminated Replace fuel
fuel
Low compression Check valves, piston,
rings, see ENGINES
Injection pump malfunction Replace injection pump,
see FUEL SYSTEMS
Fuel solenoid closes in RUN Check solenoid and
position connections









\









\









\









\









\









\









\







Engines Starts/ Incorrect slow idle Reset slow idle, see
Idles Rough W/out adjustment TUNE-UP
Smoke or Noise Injection line fuel leaks Check lines and
connections
Fuel return system blocked Check lines and
connections

Air in fuel system Bleed air from system
Incorrect or contaminated Replace fuel
fuel
Injector nozzle malfunction Check nozzles, see
FUEL SYSTEMS









\









\









\









\









\









\









\







Engines Starts Injection pump timing Reset pump timing, see
and Idles Rough incorrect FUEL SYSTEMS
W/out Smoke or Engine not fully broken in Put more miles on
Noise, But Clears engine
After Warm-Up Air in system Bleed air from system
Injector nozzle malfunction Check nozzles, see
FUEL SYSTEMS









\









\









\









\









\









\









\







Engine Idles Blocked fuel filter Replace fuel filter
Correctly, Injection pump timing Reset pump timing, see
Misfires Above incorrect FUEL SYSTEMS
Idle Incorrect or contaminated Replace fuel
fuel









\









\









\









\









\









\









\







Engine Won't Fast idle adjustment Reset fast idle, see
Return To Idle incorrect TUNE-UP
Internal injection pump Replace injection pump,
malfunction see FUEL SYSTEMS
External linkage binding Check linkage and
remove binding









\









\









\









\









\









\









\







Fuel Leaks On Loose or broken fuel line Check lines and
Ground connections
Internal injection pump Replace injection pump,
seal leak see FUEL SYSTEMS









\









\









\









\









\









\









\







Cylinder Injector nozzles sticking Test injectors, see
Knocking Noise open FUEL SYSTEMS
Very low nozzle opening Test injectors and/or
pressure replace









\









\









\









\









\









\









\







Loss of Engine Restricted air intake Remove restriction
Power EGR valve malfunction Replace EGR valve
Blocked or damaged exhaust Remove restriction
system and/or replace
components
Blocked fuel tank filter Replace filter
Restricted fuel filter Remove restriction
and/or replace filter
Block vent in gas cap Remove restriction
and/or replace cap
Tank-to-injection pump fuel Check fuel lines and
supply blocked connections
Blocked fuel return system Remove restriction
Incorrect or contaminated Replace fuel
fuel
Blocked injector nozzles Check nozzle for
blockage, see FUEL
SYSTEMS
Low compression Check valves, rings,
pistons, see ENGINES









\









\









\









\









\









\









\







Loud Engine Basic timing incorrect Reset timing, see
Noise With Black FUEL SYSTEMS
Smoke EGR valve malfunction Replace EGR valve
Internal injection pump Replace injection pump,
malfunction see FUEL SYSTEMS