NISSAN ALMERA 2001 Service Manual

SAT430D
c. Measure distance ªAº to check that torque converter is in
proper position.
Distance ªAº:
15.9 mm (0.626 in) or more
ASSEMBLY
Assembly (4) (Cont'd)
AT-469

General SpecificationsNJAT0179
Applied modelGeneral and except for Euro-OBD
QG15DE QG16DE QG18DE QG13DE QG16DE QG18DE
With catalyzer Without catalyzer
Automatic transaxle assemblyRE4F03B
3AX01 3AX19 3AX10 3AX00 3AX19 3AX10
Transaxle gear
ratio1st 2.861
2nd 1.562
3rd 1.000
4th 0.697
Reverse 2.310
Final drive 3.827 4.072 4.072 4.072 4.072 4.072
Recommended fluid Genuine Nissan ATF or equivalent*1
Fluid capacity!(Imp qt) 7.0 (6-1/8)
Applied modelMiddle East Australia Euro-OBD
RE4F03B
QG13DE QG16DE QG18DE QG16DE QG18DE QG18DE
Automatic transaxle assembly 3AX63 3AX64 3AX10 3AX19 3AX10 3AX18
Transaxle gear
ratio1st 2.861
2nd 1.562
3rd 1.000
4th 0.697
Reverse 2.310
Final drive 4.072 4.072 4.072 4.072 4.072 4.072
Recommended fluid Genuine Nissan ATF or equivalent*1
Fluid capacity!(Imp qt) 7.0 (6-1/8)
*1: Refer to MA-16, ªFluids and Lubricantsº.
Shift ScheduleNJAT0180VEHICLE SPEED WHEN SHIFTING GEARSNJAT0180S011. For General and except for Euro-OBD: QG15DE + 3AX01 model (With catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle54-62
(34 - 39)102 - 110
(63 - 68)162 - 170
(101 - 106)158 - 166
(98 - 103)92 - 100
(57 - 62)41-49
(25 - 30)54-62
(34 - 39)
Half throttle26-34
(16 - 21)51-59
(32 - 37)122 - 130
(76 - 81)70-78
(43 - 48)40-48
(25 - 30)5-13
(3-8)54-62
(34 - 39)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
AT-470

For General and except for Euro-OBD: QG16DE + 3AX19 model (With catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)96 - 104
(60 - 65)152 - 160
(94 - 99)148 - 156
(92 - 97)86-94
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
Half throttle28-36
(17 - 22)55-63
(34 - 39)119 - 127
(74 - 79)76-84
(47 - 52)36-44
(22 - 27)5-13
(3-8)50-58
(31 - 36)
For General and except for Euro-OBD: QG18DE + 3AX10 model (With catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle49-57
(30 - 35)93 - 101
(58 - 63)148 - 156
(92 - 97)144 - 152
(89 - 94)83-91
(52 - 57)41-49
(25 - 30)49-57
(30 - 35)
Half throttle26-34
(16 - 21)50-58
(31 - 36)112 - 120
(70 - 75)63-71
(39 - 44)32-40
(20 - 25)5-13
(3-8)49-57
(30 - 35)
2. For General and except for Euro-OBD: QG13DE + 3AX00 model (Without catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)95 - 103
(59 - 64)152 - 160
(94 - 99)148 - 156
(92 - 97)85-93
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
Half throttle25-33
(16 - 21)50-58
(31 - 36)1 0 3 - 111
(64 - 69)54-62
(34 - 39)32-40
(20 - 25)5-13
(3-8)50-58
(31 - 36)
For General and except for Euro-OBD: QG16DE + 3AX19 model (Without catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)96 - 104
(60 - 65)152 - 160
(94 - 99)148 - 156
(92 - 97)86-94
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
Half throttle28-36
(17 - 22)55-63
(34 - 39)119 - 127
(74 - 79)76-84
(47 - 52)36-44
(22 - 27)5-13
(3-8)50-58
(31 - 36)
For General and except for Euro-OBD: QG18DE + 3AX10 model (Without catalyzer)
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle49-57
(30 - 35)93 - 101
(58 - 63)148 - 156
(92 - 97)144 - 152
(89 - 94)83-91
(52 - 57)41-49
(25 - 30)49-57
(30 - 35)
Half throttle26-34
(16 - 21)50-58
(31 - 36)112 - 120
(70 - 75)63-71
(39 - 44)32-40
(20 - 25)5-13
(3-8)49-57
(30 - 35)
3. For the Middle East: QG13DE + 3AX63 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)95 - 103
(59 - 64)152 - 160
(94 - 99)148 - 156
(92 - 97)85-93
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
SERVICE DATA AND SPECIFICATIONS (SDS)
Shift Schedule (Cont'd)
AT-471

Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Half throttle25-33
(16 - 21)50-58
(31 - 36)1 0 3 - 111
(64 - 69)54-62
(34 - 39)32-40
(20 - 25)5-13
(3-8)50-58
(31 - 36)
For the Middle East: QG16DE + 3AX64 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)96 - 104
(60 - 65)152 - 160
(94 - 99)148 - 156
(92 - 97)86-94
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
Half throttle28-36
(17 - 22)55-63
(34 - 39)119 - 127
(74 - 79)76-84
(47 - 52)36-44
(22 - 27)5-13
(3-8)50-58
(31 - 36)
For the Middle East: QG18DE + 3AX10 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle49-57
(30 - 35)93 - 101
(58 - 63)148 - 156
(92 - 97)144 - 152
(89 - 94)83-91
(52 - 57)41-49
(25 - 30)49-57
(30 - 35)
Half throttle26-34
(16 - 21)50-58
(31 - 36)112 - 120
(70 - 75)63-71
(39 - 44)32-40
(20 - 25)5-13
(3-8)49-57
(30 - 35)
4. For Australia: QG16DE + 3AX19 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle50-58
(31 - 36)96 - 104
(60 - 65)152 - 160
(94 - 99)148 - 156
(92 - 97)86-94
(53 - 58)41-49
(25 - 30)50-58
(31 - 36)
Half throttle28-36
(17 - 22)55-63
(34 - 39)119 - 127
(74 - 79)76-84
(47 - 52)36-44
(22 - 27)5-13
(3-8)50-58
(31 - 36)
For Australia: QG18DE + 3AX10 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle49-57
(30 - 35)93 - 101
(58 - 63)148 - 156
(92 - 97)144 - 152
(89 - 94)83-91
(52 - 57)41-49
(25 - 30)49-57
(30 - 35)
Half throttle26-34
(16 - 21)50-58
(31 - 36)112 - 120
(70 - 75)63-71
(39 - 44)32-40
(20 - 25)5-13
(3-8)49-57
(30 - 35)
5. For Euro-OBD: QG18DE + 3AX18 model
Throttle positionVehicle speed km/h (MPH)
D
1®D2D2®D3D3®D4D4®D3D3®D2D2®D112®11
Full throttle51-59
(32 - 37)97 - 105
(60 - 65)154 - 162
(96 - 101)150 - 158
(93 - 98)87-95
(54 - 59)41-49
(25 - 30)51-59
(32 - 37)
Half throttle28-36
(17 - 22)52-60
(32 - 37)117 - 125
(73 - 78)66-74
(41 - 46)33-41
(21 - 25)5-13
(3-8)51-59
(32 - 37)
SERVICE DATA AND SPECIFICATIONS (SDS)
Shift Schedule (Cont'd)
AT-472

VEHICLE SPEED WHEN PERFORMING LOCK-UP=NJAT0180S02(Throttle opening: 2.0/8, Shift pattern: Comfort)
Engine model Destination OD switchVehicle speed km/h (MPH)
Lock-up ON Lock-up OFF
QG13DEGeneral and except for
Euro-OBD
Middle EastON (D
4) 76-86(48-53) 54-62(34-39)
OFF (D
3) Not applied Not applied
QG15DEGeneral and except for
Euro-OBDON (D
4) 91-99(57-62) 56-64(35-40)
OFF (D
3) Not applied Not applied
QG16DEGeneral and except for
Euro-OBD
Australia
Middle EastON (D
4) 88-96(55-60) 64-72(40-45)
OFF (D
3) 86-94(53-58) 83-91(52-57)
QG18DEGeneral (Except Taiwan)
and except for Euro-OBD
Australia
Middle EastON (D
4) 88-96(55-60) 59-67(37-42)
OFF (D
3) 86-94(53-58) 83-91(52-57)
Euro-OBD
Taiwan
South AfricaON (D
4) 92 - 100 (57 - 62) 67 - 75 (42 - 47)
OFF (D
3) 96 - 104 (60 - 65) 93 - 101 (58 - 63)
Stall RevolutionNJAT0181
Engine model Stall revolution rpm
QG13DE 2,000 - 2,300
QG15DE 2,000 - 2,300
QG16DE 2,200 - 2,700
QG18DE 2,050 - 2,500
Line PressureNJAT0182
Engine model Engine speedLine pressure kPa (bar, kg/cm
2, psi)
R position D position 2 position 1 position
QG13DEIdle 778 (7.78, 7.9, 113) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73)
Stall 1,750 (17.5, 17.9, 254)1,125 (11.25, 11.5,
163)1,125 (11.25, 11.5,
163)1,125 (11.25, 11.5,
163)
QG15DEIdle 778 (7.78, 7.9, 113) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73)
Stall1,639 (16.39, 16.7,
238)1,053 (10.53, 10.7,
153)1,053 (10.53, 10.7,
153)1,053 (10.53, 10.7,
153)
QG16DEIdle 778 (7.78, 7.9, 113) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73)
Stall1,683 (16.83, 17.2,
244)1,082 (10.82, 11.04,
157)1,082 (10.82, 11.04,
157)1,082 (10.82, 11.04,
157)
QG18DEIdle 778 (7.78, 7.9, 113) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73) 500 (5.0, 5.1, 73)
Stall1,705 (17.05, 17.4,
247)1,096 (10.96, 11.2,
159)1,096 (10.96, 11.2,
159)1,096 (10.96, 11.2,
159)
SERVICE DATA AND SPECIFICATIONS (SDS)
Shift Schedule (Cont'd)
AT-473

Control ValvesNJAT0183CONTROL VALVE AND PLUG RETURN SPRINGSNJAT0183S01Unit: mm (in)
No. Parts Part No.* Free length Outer diameter
Upper
body
Refer to
ªControl
Valve
Upper
Bodyº,
AT-397.35 3-2 timing valve spring 31736-01X00 23.0 (0.906) 6.65 (0.2618)
19 Cooler check valve spring 31742-3AX05 28.04 (1.1039) 7.15 (0.2815)
23 Pilot valve spring 31742-3AX03 38.98 (1.5346) 8.9 (0.350)
15 1-2 accumulator valve spring 31742-3AX00 20.5 (0.807) 6.95 (0.2736)
28 1-2 accumulator piston springQG13DE
model31742-3AX08 55.26 (2.1756) 19.6 (0.772)
QG15DE,
QG16DE
&
QG18DE
models31742-3AX09 55.66 (2.1913) 19.5 (0.7677)
33 1st reducing valve spring 31742-80X05 27.0 (1.063) 7.0 (0.276)
2 Overrun clutch reducing valve spring 31742-80X06 37.5 (1.476) 7.0 (0.276)
7 Torque converter relief valve spring 31742-3AX04 33.3 (1.3110) 9.0 (0.354)
10 Torque converter clutch control valve spring 31742-3AX02 53.01 (2.0870) 6.5 (0.256)
Lower
body
Refer to
ªControl
Valve
Lower
Bodyº,
AT-401.34 Shuttle valve spring 31762-41X04 51.0 (2.0079) 5.65 (0.2224)
18 Pressure regulator valve spring 31742-80X13 45.0 (1.772) 15.0 (0.591)
23 Overrun clutch control valve spring 31762-80X00 21.7 (0.854) 7.0 (0.276)
27 Accumulator control valve spring 31742-80X02 22.0 (0.866) 6.5 (0.256)
29 Shift valve A spring 31762-80X00 21.7 (0.854) 7.0 (0.276)
2 Shift valve B spring 31762-80X00 21.7 (0.854) 7.0 (0.276)
11 Pressure modifier piston spring 31742-41X15 30.5 (1.201) 9.8 (0.386)
7 Pressure modifier valve spring 31742-80X16 32.0 (1.260) 6.9 (0.272)
Ð Oil cooler relief valve spring 31872-31X00 17.02 (0.6701) 8.0 (0.315)
Ð T/C pressure spring 31742-3AX07 9.0 (0.354) 7.3 (0.287)
*: Always check with the Parts Department for the latest parts information.
Clutch and BrakesNJAT0184REVERSE CLUTCHNJAT0184S01
Number of drive plates2
Number of driven plates2
Drive plate thickness mm (in)Standard 2.0 (0.079)
Allowable limit 1.8 (0.071)
Clearance mm (in)Standard 0.5 - 0.8 (0.020 - 0.031)
Allowable limit 1.2 (0.047)
Thickness of retaining platesThickness mm (in) Part number*
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)31537-31X00
31537-31X01
31537-31X02
31537-31X03
31537-31X04
*: Always check with the Parts Department for the latest parts information.
SERVICE DATA AND SPECIFICATIONS (SDS)
Control Valves
AT-474

HIGH CLUTCHNJAT0184S021. QG13DE + 3AX00, 3AX63 models
Number of drive plates2
Number of driven plates6
Drive plate thickness mm (in)Standard 2.0 (0.079)
Allowable limit 1.4 (0.055)
Clearance mm (in)Standard 1.4 - 1.8 (0.055 - 0.071)
Allowable limit 2.4 (0.094)
Thickness of retaining platesThickness mm (in) Part number*
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
5.4 (0.213)
5.6 (0.220)
5.8 (0.228)31537-32X03
31537-32X04
31537-32X05
31537-32X06
31537-32X07
31537-32X08
31537-32X09
31537-32X10
*: Always check with the Parts Department for the latest parts information.
2. QG15DE + 3AX01 model/QG16DE + 3AX19, 3AX64 models
Number of drive plates3
Number of driven plates5
Drive plate thickness mm (in)Standard 2.0 (0.079)
Allowable limit 1.8 (0.071)
Clearance mm (in)Standard 1.4 - 1.8 (0.055 - 0.071)
Allowable limit 2.4 (0.094)
Thickness of retaining plateThickness mm (in) Part number*
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
5.4 (0.213)
5.6 (0.220)
5.8 (0.228)
6.0 (0.236)31537-32X05
31537-32X06
31537-32X07
31537-32X08
31537-32X09
31537-32X10
31537-32X11
*: Always check with the Parts Department for the latest parts information.
3. QG18DE + 3AX10, 3AX18 models
Number of drive plates3
Number of driven plates5
Drive plate thickness mm (in)Standard 1.6 (0.063)
Allowable limit 1.4 (0.055)
Clearance mm (in)Standard 1.4 - 1.8 (0.055 - 0.071)
Allowable limit 2.4 (0.094)
Thickness of retaining plateThickness mm (in) Part number*
3.6 (0.142)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)31537-32X12
31537-32X00
31537-32X01
31537-32X02
31537-32X03
31537-32X04
31537-32X05
*: Always check with the Parts Department for the latest parts information.
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch and Brakes (Cont'd)
AT-475

FORWARD CLUTCHNJAT0184S03
Number of drive plates5
Number of driven plates5
Drive plate thickness mm (in)Standard 1.8 (0.071)
Allowable limit 1.6 (0.063)
Clearance mm (in)Standard 0.45 - 0.85 (0.0177 - 0.0335)
Allowable limit 1.85 (0.0728)
Thickness of retaining plateThickness mm (in) Part number*
3.6 (0.142)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)31537-31X60
31537-31X61
31537-31X62
31537-31X63
31537-31X64
31537-31X65
*: Always check with the Parts Department for the latest parts information.
OVERRUN CLUTCHNJAT0184S04
Number of drive plates3
Number of driven plates4
Drive plate thickness mm (in)Standard 1.6 (0.063)
Allowable limit 1.4 (0.055)
Clearance mm (in)Standard 1.0 - 1.4 (0.039 - 0.055)
Allowable limit 2.0 (0.079)
Thickness of retaining plateThickness mm (in) Part number*
3.6 (0.142)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)31567-31X79
31567-31X80
31567-31X81
31567-31X82
31567-31X83
*: Always check with the Parts Department for the latest parts information.
LOW & REVERSE BRAKENJAT0184S051. QG13DE + 3AX00, 3AX63 models
Number of drive plates4
Number of driven plates3+1
Drive plate thickness mm (in)Standard 2.0 (0.079)
Allowable limit 1.8 (0.071)
Clearance mm (in)Standard 1.4 - 1.8 (0.055 - 0.071)
Allowable limit 2.8 (0.110)
Thickness of retaining plateThickness mm (in) Part number*
3.6 (0.142)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)31667-31X16
31667-31X17
31667-31X18
31667-31X19
31667-31X20
31667-31X21
*: Always check with the Parts Department for the latest parts information.
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch and Brakes (Cont'd)
AT-476

2. QG15DE + 3AX01 model/QG16DE + 3AX19, 3AX64 models/QG18DE + 3AX10, 3AX18 models
Number of drive plates5
Number of driven plates4+1
Drive plate thickness mm (in)Standard 2.0 (0.079)
Allowable limit 1.8 (0.071)
Clearance mm (in)Standard 1.4 - 1.8 (0.055 - 0.071)
Allowable limit 2.8 (0.110)
Thickness of retaining plateThickness mm (in) Part number*
3.6 (0.142)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)31667-31X16
31667-31X17
31667-31X18
31667-31X19
31667-31X20
31667-31X21
*: Always check with the Parts Department for the latest parts information.
BRAKE BANDNJAT0184S06
Anchor end pin tightening torque 3.5 - 5.8 N´m (0.35 - 0.6 kg-m, 31 - 52 in-lb)
Number of returning revolutions for anchor end pin 2.5±0.125
Lock nut tightening torque 31 - 36 N´m (3.2 - 3.7 kg-m, 23 - 27 ft-lb)
Clutch and Brake Return SpringsNJAT0185Unit: mm (in)
Parts Free length Outer diameter Part number*
Forward clutch (Overrun clutch)Outer (16 pcs) 26.6 (1.047) 10.6 (0.417) 31505-31X02
Inner (16 pcs) 26.3 (1.035) 7.7 (0.303) 31505-31X03
Reverse clutch (16 pcs) 18.6 (0.732) 8.0 (0.315) 31505-31X00
High clutch (12 pcs) 19.7 (0.776) 11.1 (0.437) 31505-31X01
Low reverse brake (20 pcs) 25.1 (0.988) 7.6 (0.299) 31505-31X04
*: Always check with the Parts Department for the latest parts information.
Oil PumpNJAT0186
Oil pump side clearance mm (in) 0.02 - 0.04 (0.0008 - 0.0016)
Thickness of inner gears and outer gearsInner gear
Thickness mm (in) Part number*
9.99 - 10.00 (0.3933 - 0.3937)
9.98 - 9.99 (0.3929 - 0.3933)
9.97 - 9.98 (0.3925 - 0.3929)31346-31X00
31346-31X01
31346-31X02
Outer gear
Thickness mm (in) Part number*
9.99 - 10.00 (0.3933 - 0.3937)
9.98 - 9.99 (0.3929 - 0.3933)
9.97 - 9.98 (0.3925 - 0.3929)31347-31X00
31347-31X01
31347-31X02
Clearance between oil pump hous-
ing and outer gear mm (in)Standard 0.08 - 0.15 (0.0031 - 0.0059)
Allowable limit 0.15 (0.0059)
Oil pump cover seal ring clearance
mm (in)Standard 0.1 - 0.25 (0.0039 - 0.0098)
Allowable limit 0.25 (0.0098)
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch and Brakes (Cont'd)
AT-477

*: Always check with the Parts Department for the latest parts information.
Input ShaftNJAT0187Unit: mm (in)
Input shaft seal ring clearanceStandard 0.08 - 0.23 (0.0031 - 0.0091)
Allowable limit 0.23 (0.0091)
Planetary CarrierNJAT0188Unit: mm (in)
Clearance between planetary carrier and pin-
ion washerStandard 0.15 - 0.70 (0.0059 - 0.0276)
Allowable limit 0.80 (0.0315)
Final DriveNJAT0189DIFFERENTIAL SIDE GEAR CLEARANCENJAT0189S01
Clearance between side gear and differential case with washer 0.1 - 0.2 mm (0.004 - 0.008 in)
DIFFERENTIAL SIDE GEAR THRUST WASHERSNJAT0189S021. QG13DE + 3AX00, 3AX63 models/QG15DE + 3AX01 modelNJAT0189S0201
Thickness mm (in) Part number*
0.75 - 0.80 (0.0295 - 0.0315)
0.80 - 0.85 (0.0315 - 0.0335)
0.85 - 0.90 (0.0335 - 0.0354)
0.90 - 0.95 (0.0354 - 0.0374)
0.95 - 1.00 (0.0374 - 0.0394)38424-31X00
38424-31X01
38424-31X02
38424-31X03
38424-31X04
*: Always check with the Parts Department for the latest parts information.
2. QG16DE + 3AX19, 3AX64 models/QG18DE + 3AX10, 3AX18 modelsNJAT0189S0202
Thickness mm (in) Part number*
0.75 - 0.80 (0.0295 - 0.0315)
0.80 - 0.85 (0.0315 - 0.0335)
0.85 - 0.90 (0.0335 - 0.0354)
0.90 - 0.95 (0.0354 - 0.0374)
0.95 - 1.00 (0.0374 - 0.0394)38424-D2111
38424-D2112
38424-D2113
38424-D2114
38424-D2115
*: Always check with the Parts Department for the latest parts information.
BEARING PRELOADNJAT0189S03
Differential side bearing preload ªTº 0.04 - 0.09 mm (0.0016 - 0.0035 in)
TURNING TORQUENJAT0189S04
Turning torque of final drive assembly 0.49 - 1.08 N´m (5.0 - 11.0 kg-cm, 4.3 - 9.5 in-lb)
DIFFERENTIAL SIDE BEARING ADJUSTING SHIMSNJAT0189S051. QG13DE + 3AX00, 3AX63 models/QG15DE + 3AX01 model/QG16DE + 3AX19, 3AX64
models
NJAT0189S0501
Thickness mm (in) Part number*
0.40 (0.0157)
0.44 (0.0173)
0.48 (0.0189)
0.52 (0.0205)
0.56 (0.0220)
0.60 (0.0236)
0.64 (0.0252)
0.68 (0.0268)38454-M8001
38454-M8003
38454-M8005
38454-M8007
38454-M8009
38454-M8011
38454-M8013
38454-M8015
*: Always check with the Parts Department for the latest parts information.
SERVICE DATA AND SPECIFICATIONS (SDS)
Input Shaft
AT-478