NISSAN NOTE 2016 Service Repair Manual

BRM-22
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
REPLACEMENT OPERATIONS
DescriptionINFOID:0000000012430802
This section is prepared for technicians who have attained a high level of skill and experience in repairing col-
lision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
Technicians are also encouraged to read Body Repair M anual (Fundamentals) in order to ensure that the orig-
inal functions and quality of the vehicle can be mainta ined. The Body Repair Manual (Fundamentals) contains
additional information, including cautions and warning, that are not including in this manual. Technicians
should refer to both manuals to ensure proper repairs.
Please note that these information are prepared for wo rldwide usage, and as such, certain procedures might
not apply in some regions or countries.
Revision: August 2015 2016 Versa Note

cardiagn.com

REPLACEMENT OPERATIONSBRM-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
The symbols used in this section for cutting and welding / brazing operations are shown below.
PIIA0149E
Revision: August 2015 2016 Versa Note

cardiagn.com

BRM-24
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
• Front pillar butt joint can be determined anywhere within shadedarea (A) as shown in the figure. The best location for the butt joint
is at position (B) due to the construc tion of the vehicle. Refer to the
front pillar section.
• Determine cutting position and record distance from the locating indent (A). Use this distance when cutting the service part. Cut
outer front pillar over 60 mm above inner front pillar cut position
(B).
• Prepare a cutting jig to make outer pillar easier to cut. Also, this will permit service part to be accurately cut at joint position.
• An example of cutting operation using a cutting jig is as follows.
1. Mark cutting lines. A: Cut position of outer pillar
B: Cut position of inner pillar
2. Align cutting line with notch on jig. Clamp jig to pillar.
3. Cut outer pillar along groove of jig. (At position A)
4. Remove jig and cut remaining portions.
5. Cut inner pillar at position in same manner.
PIIA0150E
PIIA0151E
PIIA0152E
PIIA0153E
Revision: August 2015 2016 Versa Note

cardiagn.com

REPLACEMENT OPERATIONSBRM-25
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
HoodledgeINFOID:0000000012430803
Replacement parts A. Front strut housing B. Upper front hoodledge C. Radiator core support lower
D. Hoodledge reinforcement E. Hoodledge connector F. Hoodledge reinforcement rear
G. Dash side extension Front
AWKIA2534ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BRM-26
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Front
AWKIA2552ZZ
Revision: August 20152016 Versa Note

cardiagn.com

REPLACEMENT OPERATIONSBRM-27
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
Front Side MemberINFOID:0000000012430804
AWKIA2548ZZ
Replacement parts
z Front side member outside
Front
Revision: August 2015 2016 Versa Note

cardiagn.com

BRM-28
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Front Pillar
INFOID:0000000012430805
OUTER
Work after hoodledge and hoodledge reinforcement rear has been removed.
AWKIA2538ZZ
Replacement parts
z Front side member inner
Front
Revision: August 2015 2016 Versa Note

cardiagn.com

REPLACEMENT OPERATIONSBRM-29
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
REINFORCEMENT
Work after front pillar outer has been removed.
Replacement parts z Front pillar section of body side outer
Recommended sectioning location Front
AWKIA2539ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BRM-30
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
INNER
Work after front pillar reinforcement has been removed.
Replacement partsz Front pillar reinforcement
Front
AWKIA2540ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REPLACEMENT OPERATIONSBRM-31
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
Dash SideINFOID:0000000012430806
Work with front pillar reinforcement removed.
Replacement parts z Front pillar inner reinforcement A. Mig welds
Front
ALKIA3156ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com