NISSAN TEANA 2003 Service Manual

TRUNK LID FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI

TRUNK LID FINISHERPFP:84810
Removal and InstallationBIS0011Q
REMOVAL
1. Fully open trunk lid.
2. Remove trunk lid finisher (inner). Refer to EI-35, "
DOOR FINISHER" .
3. Remove trunk lid finisher upper mounting nuts.
PIIA6259E
1. Nut 2. Seal 3. Stud bolt
4. Clip (C101) 5. Trunk lid finisher (upper) 6. Request switch harness connector
7. Trunk lid finisher (lower) 8. Clip 9. Grommet
10. Trunk lid 11. Double-faced adhesive tape
PIIA7080E

EI-34
TRUNK LID FINISHER

4. Remove trunk lid finisher upper mounting clips, and then pull out
trunk lid finisher upper toward rear of vehicle.
5. Disconnect request switch harness connector (only for models with intelligent key) after pulling out, then
remove trunk lid finisher upper.
6. Continuously, remove trunk lid finisher lower mounting clips the same as in step 4, and then remove trunk
lid finisher lower.
CAUTION:
After removal, visually inspect finisher, and if it is deformed, replace it with new molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Replace double-faced adhesive tape on back of finisher with a new tape if trunk lid finisher (lower)
is reused.

Remove double-faced adhesive tape remaining on body and back of finisher using double-faced
adhesive tape remover (SUMITOMO 3M Cleaner 30 or equivalent) when removing finisher (lower).

Install after cleaning adhesive parts of body side and back of finisher (lower).

Do not wash the vehicle within 24 hours after installing so as to keep adhesive.
PIIA7081E

DOOR FINISHER
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI

DOOR FINISHERPFP:80900
Removal and InstallationBIS0011R
1. Cap 2. Power window switch finisher (front) 3. Front door finisher
4. Front door inside seal 5. Door grip upper bracket 6. Door grip
7. Door grip finisher 8. Step lamp 9. Trunk & fuel lid opener switch
10. Seat memory switch 11. Seat memory switch finisher 12. Metal clip
13. Power window switch finisher (rear) 14. Rear door finisher
Clip Pawl Metal clip
PIIB8684E

EI-36
DOOR FINISHER

FRONT AND REAR DOOR FINISHER
Removal
1. Fully open door window.
2. Remove inside handle escutcheon cap.
3. Remove inside handle escutcheon screw.
4. Insert a remover tool A into power window switch finisher (front)
(1), lift up front end and disengage metal clip. Pull out finisher
toward front of vehicle.
CAUTION:
Lift up rear end of power window switch finisher (rear) and
disengage metal clips, and then pull out finisher toward
rear of vehicle.
5. Disconnect power window switch harness connector after pulling out, and then remove power window
switch finisher.
6. Remove power window switch screws.
7. Insert a clip clamp remover into clips on back of door trim, and
disengage clips.
CAUTION:
Insert a clip clamp remover into the part shown by the
arrow (between the clips and the body side panel). Remove
door trim.
8. Disconnect harness connector for trunk lid opener after disengaging.
9. Disconnect harness connector for seat memory switch (1) and
indirect lighting (2).
10. Disconnect harness connector for step lamp.
11. Pull up door trim and pull out toward vehicle inside, and then dis-
connect inside handle cable (3) and lock knob cable (2) from
inside handle (1).
PIIB8685E
SIIA0810E
PIIB8687E
PIIB8686E

DOOR FINISHER
EI-37
C
D
E
F
G
H
J
K
L
MA
B
EI

12. Remove door trim.
13. Remove the following parts after removing door trim.

Inside handle assembly

Trunk lid opener switch

Step lamp (front only)

Door grip

Front door inside handle

Door grip upper bracket

Seat memory switch (With automatic drive positioner)
Installation
Install in the reverse order of removal.
CAUTION:
When installing door trim, make sure that clips are securely fitted in panel holes on body, and then
press them in.

EI-38
BODY SIDE TRIM

BODY SIDE TRIMPFP:76913
Removal and InstallationBIS0011S
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
1. Front pillar garnish 2. Metal clip 3. Front body side welt
4. Front kicking plate outer 5. Front kicking plate inner 6. Center pillar lower garnish
7. Rear kicking plate inner 8. Clip (C101) 9. Rear seatback finisher
10. Rear pillar finisher 11. Rear body side welt 12. Rear kicking plate outer
13. Center pillar upper garnish
PIIA6261E

BODY SIDE TRIM
EI-39
C
D
E
F
G
H
J
K
L
MA
B
EI

FRONT PILLAR GARNISH
Removal
Remove pillar garnish mounting clips using a clip clamp remover,
and then remove pillar garnish.
Installation
Install in the reverse order of removal.
FRONT KICKING PLATE OUTER
Removal
Remove front kicking plate outer mounting clips using a clip clamp
remover, and then remove kicking plate outer.
Installation
Install in the reverse order of removal.
FRONT KICKING PLATE INNER
Removal
Remove kicking plate inner mounting clips using a clip clamp
remover, and then remove kicking plate inner.
Installation
Install in the reverse order of removal.
FRONT BODY SIDE WELT
Removal
1. Remove center pillar lower garnish.
2. Remove center kicking plate inner.
3. Remove front body side welt.
Installation
Install in the reverse order of removal.
PIIA7072E
PIIA7070E
PIIA7073E

EI-40
BODY SIDE TRIM

CENTER PILLAR LOWER GARNISH
Removal
Remove center pillar lower garnish mounting clips using a screw-
driver, and then remove center pillar lower garnish.
Installation
Install in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove center pillar lower garnish.
2. Remove front seat belt floor anchor bolt and front seat belt
shoulder anchor bolt. Refer to SB-3, "
SEAT BELTS" .
3. Remove front body side welt and rear body side welt.
4. Remove center pillar upper garnish.
Installation
Install in the reverse order of removal.
REAR KICKING PLATE OUTER
Removal
Remove rear kicking plate outer mounting clips using a clip clamp
remover, and then remove kicking plate outer.
Installation
Install in the reverse order of removal.
REAR KICKING PLATE INNER
Removal
1. Remove rear seat cushion. Refer to SE-112, "REAR SEAT" .
PIIA7077E
PIIA7078E
PIIA7071E

BODY SIDE TRIM
EI-41
C
D
E
F
G
H
J
K
L
MA
B
EI

2. Remove kicking plate inner mounting clips using a clip clamp
remover, and then remove kicking plate inner.
Installation
Install in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove center pillar lower garnish.
2. Remove rear seat cushion. Refer to SE-112, "
REAR SEAT" .
3. Remove rear kicking plate inner.
4. Remove rear body side welt.
Installation
Install in the reverse order of removal.
REAR SEATBACK FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
REAR PILLAR FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
5. Remove pillar finisher mounting clips using a screwdriver, and
then remove pillar finisher.
PIIA7074E
PIIA7075E
PIIA7076E

EI-42
BODY SIDE TRIM

CAUTION:
Insert a clip clamp remover wrapped with a shop cloth or
clip clamp remover into the part shown by the arrow
(between the clips and the body side panel). Remove clips.
Installation
Install in the reverse order of removal.
CAUTION:
Make sure that clips are securely fitted in panel holes on body when installing, and then press them in.
SIIA0810E