NISSAN TEANA 2008 Service Manual

MIR-18
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000003815765
GLASS MIRROR : Disassembly and AssemblyINFOID:0000000003815749
DISASSEMBLY
1. Place the glass mirror upward.
2. Put a strip of protective tape (B) on housing assembly.
3. As shown in the figure, insert a small flat-bladed screwdriver (A)
between glass mirror (1) and actuator (2). Push up both pawls
simultaneously to remove glass mirror lower half side.
NOTE:
Insert screwdriver, and push up while rotating (twisting) to make
work easier.
4. Remove two terminals of mirror heater attachment.
5. Lightly lift up lower side of glass mirror, and detach both pawls of upper side as if pulling it out. Disassem-
ble glass mirror from actuator.
NOTE:
Be careful not to allow grease on sealing agent in center of mirror or back side of glass mirror.
ASSEMBLY
Assemble in the reverse order of disassembly.
1. Door mirror cover 2. Side turn signal lamp assembly 3. Corner cover
4. Glass mirror 5. Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0158ZZ

OUTSIDE MIRROR
MIR-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
DOOR MIRROR COVER : Exploded ViewINFOID:0000000003815766
DOOR MIRROR COVER : Disassembly and AssemblyINFOID:0000000003815751
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1. Remove the glass mirror. Refer to MIR-18, "GLASS MIRROR : Disassembly and Assembly".
2. Remove the pawls, and disassemble the door mirror cover from
the mirror assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
1. Door mirror cover 2. Side turn signal lamp assembly 3. Corner cover
4. Glass mirror 5. Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0159ZZ

MIR-20
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
CAUTION:
After installation, visually check that pawls are securely engaged.

DOOR MIRROR REMOTE CONTROL SWITCH
MIR-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded ViewINFOID:0000000003815752
Refer to INT-30, "DRIVER SIDE : Exploded View".
Removal and InstallationINFOID:0000000003815753
REMOVAL
1. Remove the power window main switch finisher. Refer to PWC-85, "Exploded View".
2. Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using screwdriver (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0130ZZ

MWI
MWI-1
DRIVER INFORMATION & MULTIMEDIA
C
D
E
F
G
H
I
J
K
L
MB
SECTION MWI
A
O
P
CONTENTS
METER, WARNING LAMP & INDICATOR
BASIC INSPECTION ....................................4
DIAGNOSIS AND REPAIR WORKFLOW ..........4
Work flow ..................................................................4
FUNCTION DIAGNOSIS ...............................6
METER SYSTEM .................................................6
METER SYSTEM .........................................................6
METER SYSTEM : System Diagram ........................6
METER SYSTEM : System Description ....................6
METER SYSTEM : Component Parts Location ........9
METER SYSTEM : Component Description ...........10
SPEEDOMETER ........................................................10
SPEEDOMETER : System Diagram .......................10
SPEEDOMETER : System Description ...................10
SPEEDOMETER : Component Parts Location .......11
SPEEDOMETER : Component Description ............12
TACHOMETER ..........................................................12
TACHOMETER : System Diagram .........................12
TACHOMETER : System Description .....................12
TACHOMETER : Component Parts Location .........13
TACHOMETER : Component Description ..............14
ENGINE COOLANT TEMPERATURE GAUGE ........14
ENGINE COOLANT TEMPERATURE GAUGE :
System Diagram ......................................................
14
ENGINE COOLANT TEMPERATURE GAUGE :
System Description .................................................
14
ENGINE COOLANT TEMPERATURE GAUGE :
Component Parts Location ......................................
15
ENGINE COOLANT TEMPERATURE GAUGE :
Component Description ...........................................
16
FUEL GAUGE ............................................................16
FUEL GAUGE : System Diagram ...........................16
FUEL GAUGE : System Description .......................16
FUEL GAUGE : Component Parts Location ...........17
FUEL GAUGE : Component Description ................18
ODO/TRIP METER .....................................................18
ODO/TRIP METER : System Diagram ....................18
ODO/TRIP METER : System Description ................18
ODO/TRIP METER : Component Parts Location ....19
ODO/TRIP METER : Component Description .........20
SHIFT POSITION INDICATOR ..................................20
SHIFT POSITION INDICATOR : System Diagram ....20
SHIFT POSITION INDICATOR : System Descrip-
tion ...........................................................................
20
SHIFT POSITION INDICATOR : Component
Parts Location ..........................................................
21
SHIFT POSITION INDICATOR : Component De-
scription ...................................................................
22
WARNING LAMPS/INDICATOR LAMPS ..................22
WARNING LAMPS/INDICATOR LAMPS : System
Diagram ...................................................................
22
WARNING LAMPS/INDICATOR LAMPS : System
Description ...............................................................
22
WARNING LAMPS/INDICATOR LAMPS : Com-
ponent Parts Location ..............................................
23
WARNING LAMPS/INDICATOR LAMPS : Com-
ponent Description ...................................................
24
METER ILLUMINATION CONTROL .........................24
METER ILLUMINATION CONTROL : System Di-
agram ......................................................................
24
METER ILLUMINATION CONTROL : System De-
scription ...................................................................
24
METER ILLUMINATION CONTROL : Component
Parts Location ..........................................................
26
METER ILLUMINATION CONTROL : Component
Description ...............................................................
27
INFORMATION DISPLAY ..........................................27
INFORMATION DISPLAY : System Diagram ..........27
INFORMATION DISPLAY : System Description .....27
INFORMATION DISPLAY : Component Parts Lo-
cation .......................................................................
30
INFORMATION DISPLAY : Component Descrip-
tion ...........................................................................
31

MWI-2
DIAGNOSIS SYSTEM (METER) .......................32
Diagnosis Description .............................................32
CONSULT-III Function (METER/M&A) ...................33
COMPONENT DIAGNOSIS ........................37
U1000 CAN COMM CIRCUIT ............................37
Description ..............................................................37
DTC Logic ...............................................................37
Diagnosis Procedure .............................................37
U1010 CONTROL UNIT (CAN) .........................38
Description ..............................................................38
DTC Logic ...............................................................38
Diagnosis Procedure ..............................................38
B2205 VEHICLE SPEED ...................................39
Description ..............................................................39
DTC Logic ...............................................................39
Diagnosis Procedure .............................................39
B2267 ENGINE SPEED .....................................40
Description ..............................................................40
DTC Logic ...............................................................40
Diagnosis Procedure ..............................................40
B2268 WATER TEMP ........................................41
Description ..............................................................41
DTC Logic ...............................................................41
Diagnosis Procedure ..............................................41
POWER SUPPLY AND GROUND CIRCUIT .....42
COMBINATION METER ...........................................42
COMBINATION METER : Diagnosis Procedure ....42
BCM (BODY CONTROL MODULE) .........................42
BCM (BODY CONTROL MODULE) : Diagnosis
Procedure ...............................................................
42
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) .............................
43
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) : Diagnosis Pro-
cedure .....................................................................
43
FUEL LEVEL SENSOR SIGNAL CIRCUIT .......45
Description ..............................................................45
Component Function Check ...................................45
Diagnosis Procedure .............................................45
Component Inspection ............................................46
METER CONTROL SWITCH SIGNAL CIR-
CUIT ...................................................................
48
Description ..............................................................48
Diagnosis Procedure ..............................................48
Component Inspection ............................................49
OIL PRESSURE SWITCH SIGNAL CIRCUIT ...50
Description ..............................................................50
Component Function Check ...................................50
Diagnosis Procedure ..............................................50
Component Inspection ............................................50
PARKING BRAKE SWITCH SIGNAL CIR-
CUIT ...................................................................
52
Description ..............................................................52
Diagnosis Procedure ...............................................52
Component Inspection ............................................52
ECU DIAGNOSIS .......................................53
COMBINATION METER ....................................53
Reference Value .....................................................53
Wiring Diagram - METER - .....................................59
Fail-Safe ..................................................................66
DTC Index ...............................................................67
BCM (BODY CONTROL MODULE) ..................68
Reference Value .....................................................68
Wiring Diagram - BCM - ..........................................91
Fail-safe ..................................................................97
DTC Inspection Priority Chart ...............................99
DTC Index ............................................................100
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ................
102
Reference Value ...................................................102
Wiring Diagram - IPDM E/R - ................................110
Fail-safe ................................................................113
DTC Index ............................................................115
SYMPTOM DIAGNOSIS ...........................116
THE FUEL GAUGE POINTER DOES NOT
MOVE ................................................................
116
Description ............................................................116
Diagnosis Procedure .............................................116
THE METER CONTROL SWITCH IS INOPER-
ATIVE ................................................................
117
Description ............................................................117
Diagnosis Procedure .............................................117
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN ON ......................................
118
Description ............................................................118
Diagnosis Procedure .............................................118
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN OFF ....................................
119
Description ............................................................119
Diagnosis Procedure .............................................119
THE PARKING BRAKE RELEASE WARNING
CONTINUES DISPLAYING, OR DOES NOT
DISPLAY ...........................................................
120
Description ............................................................120
Diagnosis Procedure .............................................120
THE DOOR OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY ........
121
Description ............................................................121

MWI
MWI-3
C
D
E
F
G
H
I
J
K
L
MB A
O
P Diagnosis Procedure .............................................
121
THE TRUNK OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY ........
122
Description ............................................................122
Diagnosis Procedure .............................................122
THE AMBIENT TEMPERATURE DISPLAY IS
INCORRECT .....................................................
123
Description ............................................................123
Diagnosis Procedure .............................................123
NORMAL OPERATING CONDITION ...............124
INFORMATION DISPLAY .......................................124
INFORMATION DISPLAY : Description ................124
PRECAUTION ............................................125
PRECAUTIONS ...............................................125
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
125
ON-VEHICLE REPAIR ...............................126
COMBINATION METER .................................126
Exploded View .......................................................126
Removal and Installation .......................................126
Disassembly and Assembly ...................................126
METER CONTROL SWITCH ..........................127
Exploded View .......................................................127
Removal and Installation .......................................127

MWI-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work flowINFOID:0000000003792506
OVERALL SEQUENCE
• Reference 1···MWI-32, "Diagnosis Description".
 Reference 2···MWI-67, "
DTC Index".
 Reference 3···MWI-42, "
COMBINATION METER : Diagnosis Procedure".
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.CHECK SYMPTOM
JSNIA0542GB

MWI
DIAGNOSIS AND REPAIR WORKFLOW
MWI-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 Check the symptom based on the information obtained from the customer.
 Check that any other malfunctions are present.
>> GO TO 3.
3.CHECK ON BOARD DIAGNOSIS OPERATION
Check that the on board diagnosis function operates. Refer to MWI-32, "
Diagnosis Description".
Does the on board diagnosis function operate normally?
YES >> GO TO 4.
NO >> GO TO 6.
4.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS
Connect CONSULT-III and perform self-diagnosis. Refer to MWI-33, "
CONSULT-III Function (METER/M&A)".
Are self-diagnosis results normal?
YES >> GO TO 5.
NO >> GO TO 8.
5.NARROW DOWN THE MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 7.
6.CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUITS
Inspect combination meter power supply and ground circuits. Refer to MWI-42, "
COMBINATION METER :
Diagnosis Procedure".
Is inspection result OK?
YES >> GO TO 7.
NO >> GO TO 8.
7.REPLACE COMBINATION METER
Replace combination meter.
>> GO TO 9.
8.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace the malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repair or replace malfunctioning parts.
>> GO TO 9.
9.FINAL CHECK
Check that the combination meter operates normally.
Do they operate normally?
YES >> INSPECTION END
NO >> GO TO 1.

MWI-6
< FUNCTION DIAGNOSIS >
METER SYSTEM
FUNCTION DIAGNOSIS
METER SYSTEM
METER SYSTEM
METER SYSTEM : System DiagramINFOID:0000000003792507
METER SYSTEM : System DescriptionINFOID:0000000003792508
COMBINATION METER
 The combination meter receives the information required to control the operation of each gauge, indicator/
warning lamp, and information display via CAN communication from each unit, each switch, and sensor.
 The combination meter incorporates a trip computer that displays warnings and messages on the informa-
tion display according to the information received from various units.
 The combination meter incorporates a buzzer function that sounds an audible alarm with the integrated
buzzer device. Refer to WCS-5, "
WARNING CHIME SYSTEM : System Description" for further details.
 The combination meter integrates the meter circuit check function and the segment check function that
checks the information display operation.
IPDM E/R
 IPDM E/R reads the ON/OFF signals of the oil pressure switch and transmits the oil pressure switch signal to
the combination meter via BCM with the CAN communication line.
 IPDM E/R is equipped with the diagnosis function. It can perform the operation check of oil pressure warning
lamp with the auto active test and the diagnosis with CONSULT-III.
METER CONTROL FUNCTION LIST
JPNIA1011GB