NISSAN TEANA 2014 Service Manual

DIAGNOSIS SYSTEM (ECM)EC-611
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
DTC WORK SUPPORT MODE
Test Item
FUEL PUMP RE-
LAY • Ignition switch: ON (Engine
stopped)
• Turn the fuel pump relay “ON” and “OFF” using CONSULT and
listen to operating sound. Fuel pump relay makes the operat-
ing sound. • Harness and connectors
• Fuel pump relay
VIAS S/V-1 • Ignition switch: ON
• Turn solenoid valve “ON” and “OFF” using CONSULT and listen
to operating sound. Solenoid valve makes the operating
sound. • Harness and connectors
• Solenoid valve
ENGINE
MOUNTING • Ignition switch: ON
• Turn electronic controlled engine mount “IDLE” and “TRVL” with
CONSULT. Electronic controlled engine mount
makes the operating sound. • Harness and connectors
• Electronic controlled engine mount
VIAS S/V-2 • Ignition switch: ON
• Turn solenoid valve “ON” and “OFF” using CONSULT and listen
to operating sound. Solenoid valve makes the operating
sound. • Harness and connectors
• Solenoid valve
IGNITION TIM-
ING • Engine: Return to the original
non-standard condition
• Timing light: Set
• Retard the ignition timing using
CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. Perform Idle Air Volume Learning.
POWER BAL-
ANCE • Engine: After warming up, idle the
engine.
• A/C switch OFF
• Selector lever: P or N position
• Cut off each injector signal one at a time using CONSULT. Engine runs rough or stops. • Harness and connectors
• Compression
• Fuel injector
• Power transistor
•Spark plug
• Ignition coil
VENT CON-
TROL/V • Ignition switch: ON (Engine
stopped)
• Turn solenoid valve “ON” and “OFF” with the CONSULT and lis-
ten to operating sound. Solenoid valve makes an operating
sound. • Harness and connectors
• Solenoid valve
V/T ASSIGN AN-
GLE • Engine: Return to the original
non-standard condition
• Change intake valve timing using
CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Intake valve timing control sole- noid valve
COOLING FAN* • Ignition switch: ON
• Turn the cooling fan “HI”, “MID”, “LOW” and “OFF” using CON-
SULT. Cooling fan moves and stops.
• Harness and connectors
• Cooling fan motor
•IPDM E/R
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
Test mode Test item Corresponding DTC No. Reference page
A/F SEN1 A/F SEN1(B1) P1276 P0130
EC-753
A/F SEN1(B2) P1286 P0150EC-753
EVAPORATIVE SYSTEMPURG FLOW P0441 P0441
EC-828PURG VOL CN/V P1444 P0443EC-833
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-612
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
SRT & P-DTC MODE
SRT STATUS Mode
• For items whose SRT codes are set, “CMPLT” is
displayed on the CONSULT screen; for items whose SRT
codes are not set, “INCMP” is displayed.
• “SRT STATUS” provides the presence or absenc e of permanent DTCs stored in ECM memory.
PERMANENT DTC STATUS Mode
How to display permanent DTC status
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC ST ATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
NOTE:
Permanent DTCs stored in ECM memory are display ed on the CONSULT screen to show if a driving pat-
tern required for erasing permanent DTCs is complete (CMPLT) or incomplete (INCMP).
CAUTION:
Since the “PERMANENT DTC STATUS” screen displ ays the previous trip information, repeat the
following twice to update the in formation: “Ignition switch OFF” , “Wait for more than 10 seconds”
and “Ignition switch ON”.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
PERMANENT DTC WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to comp lete the driving pattern that is required for erasing
permanent DTC.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
HO2S2HO2S2(B1) P1146 P0138
EC-768
HO2S2(B1) P1147 P0137EC-763
HO2S2(B1) P0139 P0139EC-775
HO2S2(B2) P1166 P0158EC-768
HO2S2(B2) P1167 P0157EC-763
HO2S2(B2) P0159 P0159EC-775
Test mode Test item Corresponding DTC No. Reference page
JSBIA0062GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-613
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000009462542
VALUES ON THE DIAGNOSIS TOOL
NOTE:
• The following table includes information (items) inapplicable to this vehicle. For information (items) applica- ble to this vehicle, refer to CONSULT display items.
• Numerical values in the following table are reference values.
• These values are input/output values that ECM receiv es/transmits and may differ from actual operations.
Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the
data monitor.
This occurs because the timing light shows a value calculated by ECM according to signals received from
the camshaft position sensor and other sensors related to ignition timing.
• For outlines of following items, refer to EC-601, "CONSULT Function"
.
Monitor Item Condition Values/Status
ENG SPEED Run engine and compare CONSULT value with the tachometer indication.Almost the same speed as
the tachometer indication.
MAS A/F SE-B1 See EC-701, "Description"
.
B/FUEL SCHDL See EC-701, "Description"
.
A/F ALPHA-B1 See EC-701, "Description"
.
A/F ALPHA-B2 See EC-701, "Description"
.
COOLAN TEMP/S Engine: After warming up More than 70 °C (158 °F)
A/F SEN1 (B1) Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
A/F SEN1 (B2) Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
HO2S2 (B1) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 (B2) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 MNTR(B1) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
←→ RICH
HO2S2 MNTR(B2) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
←→ RICH
VHCL SPEED SE Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
speedometer indication
BATTERY VOLT Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1 Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
ACCEL SEN 2*
1Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-614
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
TP SEN 1-B1• Ignition switch: ON
(Engine stopped)
• Selector lever: D position Accelerator pedal: Fully re
leased More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*
1• Ignition switch: ON (Engine stopped)
• Selector lever: D position Accelerator pedal: Fully re
leased More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE Ignition switch: ON Indicates fuel tank tempera-
ture
EVAP SYS PRES Ignition switch: ON Approx. 1.8 - 4.8 V
FUEL LEVEL SE Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL Ignition switch: ON → START → ON Off → On → Off
CLSD THL POS Ignition switch: ON
(Engine stopped) Accelerator pedal:
Fully released On
Accelerator pedal: Slightly depressed Off
AIR COND SIG Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates.) On
PW/ST SIGNAL Engine: After warming up, idle the
engine Steering wheel: Not being turned Off
Steering wheel: Being turned On
LOAD SIGNAL Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2nd position On
Rear window defogger switch and lighting
switch: OFF Off
IGNITION SW Ignition switch: ON → OFF → ON On → Off → On
HEATER FAN SW Engine: After warming up, idle the
engine Heater fan switch: ON On
Heater fan switch: OFF Off
BRAKE SW Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
INJ PULSE-B1 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
INJ PULSE-B2 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
IGN TIMING • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 7 - 17
°BTDC
2,000 rpm 25 - 45 °BTDC
CAL/LD VALUE • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 5 - 35%
2,500 rpm 5 - 35%
MASS AIRFLOW • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 6.0 g/s
2,500 rpm 7.0 - 20.0 g/s
PURG VOL C/V • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.) 0%
2,000 rpm —
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-615
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
INT/V TIM (B1)
• Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V TIM (B2) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V SOL(B1) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
INT/V SOL(B2) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
VIAS S/V-1 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→On → Off
VIAS S/V-2 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→On → Off
AIR COND RLY Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates) On
ENGINE MOUNT Engine: After warming up Below 950 rpm IDLE
Above 950 rpm TRVL
FUEL PUMP RLY • For 1 second after turning ignition switch: ON
• Engine running or cranking On
Except above Off
VENT CONT/V Ignition switch: ON Off
THRTL RELAY Ignition switch: ON On
A/F S1 HTR(B1) Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
A/F S1 HTR(B2) Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
COOLING FAN • Engine: After warming up, idle the
engine
• Air conditioner switch: OFF Engine coolant temperature: 97
°C
(206 °F) or less OFF
Engine coolant temperature: Between
98 °C (208
°F) and 99 °C (210 °F) LOW
Engine coolant temperature: Between
100 °C (212 °F) and 104 °C (219 °F) MID
Engine coolant temperature: 105 °C
(221 °F) or more HI
HO2S2 HTR (B1) Engine speed: Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load On
Engine speed: Above 3,600 rpm Off
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-616
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
HO2S2 HTR (B2)Engine speed: Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load On
Engine speed: Above 3,600 rpm Off
ALT DUTY SIG Power generation voltage variable control: Operating On
Power generation voltage variable control: Not operating Off
I/P PULLY SPD Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
the speedometer indication
IDL A/V LEARN Engine: Running Idle air volume learning has not been per-
formed yet. YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL Ignition switch: ON Vehicle has traveled after MIL has illumi-
nated. 0 - 65,535 km
(0 - 40,723 miles)
ENG OIL TEMP Engine: After warming up More than 70 °C (158 °F)
VHCL SPEED SE Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
the speedometer indication
SET VHCL SPD Engine: Running ASCD: Operating The preset vehicle speed is
displayed
MAIN SW Ignition switch: ON MAIN switch: Pressed On
MAIN switch: Released Off
CANCEL SW Ignition switch: ON CANCEL switch: Pressed On
CANCEL switch: Released Off
RESUME/ACC SW Ignition switch: ON RESUME/ACCELERATE switch:
Pressed On
RESUME/ACCELERATE switch: Re-
leased Off
SET SW Ignition switch: ON SET/COAST switch: Pressed On
SET/COAST switch: Released Off
BRAKE SW1
(Brake pedal posi-
tion switch) Ignition switch: ON Brake pedal: Fully released On
Brake pedal: Slightly depressed Off
BRAKE SW2
(Stop lamp switch) Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
VHCL SPD CUT Ignition switch: ON Non
LO SPEED CUT Ignition switch: ON Non
AT OD MONITOR Ignition switch: ON Off
AT OD CANCEL Ignition switch: ON Off
CRUISE LAMP Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time On
→ Off
SET LAMP • MAIN switch: ON
• When vehicle speed is between 40 km/h (25 MPH) and 144 km/h
(89 MPH) ASCD: Operating On
ASCD: Not operating Off
ALT DUTY Engine: Idle 0 - 80%
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-617
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
BAT CUR SEN
• Engine speed: Idle
• Battery: Fully charged*
2
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Approx. 2,600 - 3,500 mV
A/F ADJ-B1 Engine: Running −0.330 - 0.330
A/F ADJ-B2 Engine: Running −0.330 - 0.330
P/N POSI SW Ignition switch: ON Selector lever: P or N position On
Selector lever: Except above position Off
INT/A TEMP SE Ignition switch: ON Indicates intake air tempera-
ture
AC PRESS SEN • Engine: Idle
• Both A/C switch and blower fan switch: ON (Compressor operates) 1.0 - 4.0 V
VTC DTY EX B2
*3— —
EVAP LEAK DIAG Ignition switch: ON Indicates the condition of
EVAP leak diagnosis.
EVAP DIAG READY Ignition switch: ON Indicates the ready condition
of EVAP leak diagnosis.
BAT TEMP SEN • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
Indicates the temperature
around the battery.
THRTL STK CNT
B1
*3— —
HO2 S2 DIAG1(B2) DTC P0159 self-diagnosis (delayed response) has not been performed yet. INCMP
DTC P0159 self-diagnosis (delayed response) has already been performed suc-
cessfully. CMPLT
A/F SEN1 DIAG1
(B2) DTC P015C and P015D self-dia
gnosis is incomplete. INCMP
DTC P015C and P015D self-dia gnosis is complete. CMPLT
A/F SEN1 DIAG1
(B1) DTC P015A and P015B self-diagnosis is incomplete. INCMP
DTC P015A and P015B self-diagnosis is complete. CMPLT
A/F SEN1 DIAG2
(B2) DTC P014E and P014F self-diagnosis is incomplete. INCMP
DTC P014E and P014F self-diagnosis is complete. CMPLT
A/F SEN1 DIAG2
(B1) DTC P014C and P014D self-dia
gnosis is incomplete. INCMP
DTC P014C and P014D self-dia gnosis is complete. CMPLT
A/F SEN1 DIAG3
(B2) The vehicle condition is not within the diagnosis range of DTC P014E, P014F,
P015C or P015D. ABSNT
The vehicle condition is within the diagnosis range of DTC P014E, P014F,
P015C or P015D. PRSNT
A/F SEN1 DIAG3
(B1) The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B. ABSNT
The vehicle condition is within the diagnosis range of DTC P014C, P014D,
P015A or P015B. PRSNT
HO2 S2 DIAG2(B2) DTC P0159 self-diagnosis (slow response) has not been performed yet. INCMP
DTC P0159 self-diagnosis (slow response) has already been performed suc-
cessfully. CMPLT
HO2 S2 DIAG2(B1) DTC P0139 self-diagnosis (slow response) has not been performed yet. INCMP
DTC P0139 self-diagnosis (slow response) has already been performed suc-
cessfully. CMPLT
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

E C -618
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
*1: Accelerator pedal position sensor 2 signal and throttle
position sensor 2 signal are converted by ECM inter-
nally. Thus, they differ from ECM terminals voltage signal.
*2: Before measuring the terminal voltage, confir m that the battery is fully charged. Refer to PG-4, "How to
Handle Battery".
*3: The item is indicated, but not used.
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
• ECM is located in the engine room left side near battery.
• Specification data are reference values.
• Pulse signal is measured by CONSULT.
EOP SENSOR • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle Approx. 1,450 mV
2,000 rpm Approx. 2,850 mV
HO2 S2 DIAG1(B1) DTC P0139 self-diagnosis (delayed response) has not been performed yet. INCMP
DTC P0139 self-diagnosis (delayed response) has already been performed suc-
cessfully. CMPLT
A/F-S ATMSPHRC
CRCT B1 Engine: After warming up, idle the engine Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT B2 Engine: After warming up, idle the engine
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT UP B1 Engine: Running Varies depending on the
number of updates.
A/F-S ATMSPHRC
CRCT UP B2 Engine: Running Varies depending on the
number of updates.
Monitor Item Condition Values/Status
JSBIA0505ZZ
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
1
(R) 128
(GR) Throttle contro
l motor power
supply Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
2
(BG) 128
(GR) Throttle control mo
tor (Close) Output [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re-
leased 0 - 14 V
JMBIA1125GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-619
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
3
(SB) 128
(GR) A/F sensor 1 heater (bank 2) Output [Engine is running]
• Warm-up condition
• Idle speed (More than 140 seconds after
starting engine) 2.9 - 8.8 V
4
(LG) 107
(P) Engine oil pressure sensor Input [Engine is running]
• Warm-up condition
• Idle speed 1.3 V
[Engine is running]
• Warm-up condition
• Engine speed is 2,000 rpm 2.7 V
5
(P) 128
(GR) Throttle control motor (Open) Output [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully de-
pressed 0 - 14 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re- leased 0 - 14 V
6
(BR) 128
(GR) A/F sensor 1 heater
(bank 1) Output[Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine) 2.9 - 8.8 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0030GB
JPBIA3359ZZ
JPBIA3360ZZ
JMBIA0031GB
JMBIA0032GB
JMBIA0902GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-620
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
9
(LG)
128
(GR) Ignition signal No. 3
Output[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes de-
pending on rpm at idle 0 - 0.2 V
10
(LG) Ignition signal No. 2
11
(LG) Ignition signal No. 1
13
(LG) Ignition signal No. 6
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 0.1 - 0.4 V
14
(LG) Ignition signal No. 5
15
(LG) Ignition signal No. 4
12
(B) — ECM ground — — —
16
(B) — ECM ground — — —
19
(B) —Sensor ground
(Throttle position sensor) —— —
22
(W) 128
(GR) Throttle position sensor 1 Input [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re- leased More than 0.36 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully de- pressed Less than 4.75 V
23
(R) 128
(GR) Throttle position sensor 2 Input [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re-
leased Less than 4.75 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully de- pressed More than 0.36 V
24
(G) 19
(B) Sensor power supply
(Throttle position sensor) — [Ignition switch: ON] 5 V
26
(SB) 128
(GR) Power supply for ECM (Back-
up) Input [Ignition switch: OFF] BATTERY VOLTAGE
(11 - 14 V)
31
(Y) 128
(GR) ECM relay
(Self shut-off) Output• [Engine is running]
• [Ignition switch: OFF] A few seconds after turning
ignition switch OFF 0 - 1.5 V
[Ignition switch: OFF]
More than a few seconds after
turning ignition switch OFF BATTERY VOLTAGE
(11 - 14 V)
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0035GB
JMBIA0036GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM