NISSAN TEANA 2014 Service Manual

FUEL FILLER LID OPENERDLK-213
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
FUEL FILLER LID OPENER
Exploded ViewINFOID:0000000009461961
FUEL FILLER LID
FUEL FILLER LID : Re moval and InstallationINFOID:0000000009461962
REMOVAL
1. Fully open fuel filler lid.
2. Remove fuel cap pin (1).
1. Fuel filler lid opener cable 2. Spring 3. Fuel filler lid
4. Bumper rubber 5. Fuel filler lid lock A. Clip
B. Cable protector
ALKIA2730ZZ
JMKIA8137ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-214
< REMOVAL AND INSTALLATION >
FUEL FILLER LID OPENER
3. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specifications for a correctly installed fuel filler lid.
• Fitting adjustment cannot be performed.
Unit: mm (in)
FUEL FILLER OP ENER CABLE
FUEL FILLER OPENER CABLE : Removal and InstallationINFOID:0000000009461963
REMOVAL
1. Remove hood and fuel filler handle assembly bolts (A).
2. Disengage fuel filler lid opener cable (2) by pulling downward and then sliding cable end to the side to remove from hood and
fuel filler handle assembly (1).
3. Remove dash side finisher (LH). Refer to INT-20, "DASH SIDE FINISHER : Removal and Installation"
.
4. Remove center pillar lower finisher (LH). Refer to INT-23, "CENTER PILLAR LOWER FINISHER :
Removal and Installation".
5. Remove rear seat bolster (LH). Refer to SE-38, "Removal and Installation - Rear Seat Bolster"
.
ALKIA2732ZZ
Portion Measurement Standard
Fuel filler lid – Body side outer Clearance 3.5 ± 1.0 (0.14 ± 0.04)
Fuel filler lid – Body side outer Surface height 0.0 ± 1.0 (0.0 ± 0.04)
JMKIA7998ZZ
JMKIA7999ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FUEL FILLER LID OPENERDLK-215
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
6. Remove trunk side finisher (LH). Refer to INT-34, "TRUNK SIDE FINISHER : Removal and Installation".
7. Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to DLK-215, "FUEL FILLER LID
LOCK : Removal and Installation".
8. Disengage each harness protector (1), and then remove fuel filler lid opener cable (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and InstallationINFOID:0000000009461964
REMOVAL
1. Fully open fuel filler lid.
2. Insert a suitable tool (A) as shown into bottom of fuel filler lock assembly(1).
3. Release lower pawls (A) using a suitable tool and remove fuel filler lid lock assembly (1) from opening.
CAUTION:
Be careful not to damage gasket (2) when removing.
JMKIA5720ZZ
ALKIA2731ZZ
JMKIA8138ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-216
< REMOVAL AND INSTALLATION >
FUEL FILLER LID OPENER
4. Disconnect fuel filler lid opener cable (1) by pulling downwardand then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
JMKIA8139ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

KEY CYLINDERDLK-217
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
KEY CYLINDER
GLOVE BOX LID KEY CYLINDER
GLOVE BOX LID KEY CYLINDER : Removal and InstallationINFOID:0000000009461965
REMOVAL
1. Remove glove box assembly (2) to access glove box lid key cyl-
inder (1). Refer to IP-22, "Removal and Installation"
.
2. Insert key (1) into glove box lid lock cylinder (2).
3. Pull upward on glove box lid release handle (3).
4. Rotate key (1) and turn glove box lid key cylinder (2) to the lock position.
5. Press tumbler stopper (1) into glove box lid lock cylinder (2) using a suitable tool (A), and then remove key (3) and glove box
lid lock cylinder together from glove box lid release handle (4).
NOTE:
When removing glove box lid lock cylinder (2) note the position
of cylinder to glove box lid release handle (4).
6. Remove sleeve (3) from glove box lid release handle and then install sleeve to glove box lid lock cylinder.
NOTE:
When removing sleeve note the position of sleeve to glove box
lid release handle.
CAUTION:
Do not pull out key (1) from glove box lid lock cylinder (2)
while sleeve (3) is removed. Othe rwise, tumblers (4) may be
lost from glove box lid lock cylinder.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check glove box assem bly open/close, lock/unlock operation.
ALKIA2719ZZ
JMKIA5490ZZ
JMKIA5491ZZ
JMKIA5819ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-218
< REMOVAL AND INSTALLATION >
KEY CYLINDER
SEATBACK LOCK KEY CYLINDER
SEATBACK LOCK KEY CYLINDER : Removal and InstallationINFOID:0000000009461966
REMOVAL
1. Remove rear parcel shelf finisher. Refer to INT-26, "Removal and Installation".
2. Remove bolts (A) and the setback lock key cylinder (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, rear seatback assembl y open/close, lock/unlock operation.
ALKIA2738ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR SWITCHDLK-219
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR SWITCH
Removal and InstallationINFOID:0000000009461967
REMOVAL
1. Remove the door switch bolt (A).
2. Disconnect the harness connector from the door switch (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2509ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-220
< REMOVAL AND INSTALLATION >
INSIDE KEY ANTENNA
INSIDE KEY ANTENNA
CONSOLE
CONSOLE : Removal and InstallationINFOID:0000000009461968
REMOVAL
1. Remove the center console rear finisher (1). Refer to IP-18,
"Removal and Installation".
2. Remove the inside key antenna (console) screws (A) and inside key antenna (console) (2).
INSTALLATION
Installation is in the reverse order of removal.
LUGGAGE ROOM
LUGGAGE ROOM : Removal and InstallationINFOID:0000000009461969
REMOVAL
1. Disconnect the harness connector (A) from the inside keyantenna (luggage room) (1).
2. Remove the inside key antenna (luggage room) clips (B), and then remove inside key antenna (luggage room) (1).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2720ZZ
ALKIA2721ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

OUTSIDE KEY ANTENNADLK-221
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Removal and InstallationINFOID:0000000009461970
REMOVAL
The driver side outside key antenna and driver side outside handle are serviced as an assembly. Refer to
DLK-198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
INSTALLATION
Installation is in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and InstallationINFOID:0000000009461971
REMOVAL
The passenger side outside key antenna and passenger side outside handle are serviced as an assembly.
Refer to DLK-198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
INSTALLATION
Installation is in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Remo val and InstallationINFOID:0000000009461972
REMOVAL
1. Remove rear bumper fascia. Refer to EXT-21, "Removal and Installation".
2. Disconnect the harness connector (B) from the rear bumper key
antenna (1).
3. Remove the nuts (A) that retain the rear bumper key antenna (1) to the body.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2723ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-222
< REMOVAL AND INSTALLATION >
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH
DRIVER SIDE
DRIVER SIDE : Removal and InstallationINFOID:0000000009461973
REMOVAL
The driver side door request switch and driver side outside handle are serviced as an assembly. Refer to DLK-
198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle".
INSTALLATION
Installation is in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and InstallationINFOID:0000000009461974
REMOVAL
The passenger side door request switch and passenger side outside handle are serviced as an assembly.
Refer to DLK-198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
INSTALLATION
Installation is in the reverse order of removal.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM