Peugeot 206 Dag 2002.5 Owner's Guide

24-02-2003
INSTRUMENTS AND CONTROLS
32
Engine oil temperature indicator With the engine running, this indi- cates the oil temperature:
Ð needle in zone (C), the tempera-
ture is correct,
Ð needle in zone (D), the tempera-
ture is too high. To lower the oil temperature, reduce your speed.
Coolant temperature indicator
Ð needle in zone (A), the temperature
is correct,
Ð needle in zone (B), the temperature
is too high. The central STOPwarn-
ing light flashes.
You must stop.
Consult a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS33
Instrument panel display After switching on the ignition, three functions are shown in succession:
Ð service indicator (see corresponding section),
Ð engine oil level indicator,
Ð total distance recorder/total and trip distances.Note: the total and trip distances are displayed for 30 seconds when the ignition is switched off, on opening the driver's door,
as well as on locking and unlocking the vehicle. Engine oil level When the ignition is switched on, the engine oil level is indicated for approximately 10 seconds, after the servicing informati on.
Maximum Check the level using the dipstick to confirm whether the level indicated is correct; a surplus of oil can cause damage to the engine.
Consult a PEUGEOT dealer without delay. Minimum.
Check the level with the dipstick and top it up. The level indicated is only correct if the vehicle has been on stable, level ground, with the engine stopped, for 10 minutes. Oil level gauge fault The 6 segments flash to indicate a fault in the oil level gauge.There is a risk the engine will be damaged.
Consult a PEUGEOT dealer.
24-02-2003

24-02-2003
INSTRUMENTS AND CONTROLS
34
Total distance recorde Briefly pressing button
1alternates
between the total and trip distance displays.
To reset the trip recorder to zero, when it is displayed press the buttonfor more than 3 seconds. Hazard warning lights
Press the button, the direction indica-tors flash.
They can operate with the ignition off. Automatic lighting of hazard warning lights*
When braking in an emergency, depending on the force of decelera-tion, the hazard warning lights come
on automatically. They switch off auto-matically the first time you accelerate.
It is also possible to switch them off by pressing the button.
* According to destination.
Lighting rheostat With the lights on, press the button to vary the intensity of the lighting ofthe instrument panel and the multi-
function display. When the lightingreaches the minimum (or maximum)setting, release the button thenpress it again to increase (or reduce)the brightness. As soon as the lighting is of the required brightness, release thebutton.

24-02-2003
YOUR 206 IN DETAIL35
DISPLAY A This displays the following information:
Ð the time,
Ð the date,
Ð the outside temperature (this
flashes if there is a risk of ice),
Ð the audio system displays,
Ð a door check (e.g.: ''left front door open''),
Ð warning messages (e.g. ''remote control battery flat'') or information messages (e.g. ''economy mode
active''), displayed temporarily. Adjusting the parameters Press and hold button
1for two seconds to access the settings; the data
flashes, indicating it is ready to be modified. Then, each press of button 1scrolls through the various data in the following
order:
Ð language of information displayed,
Ð hours (12 then 24 hour mode),
Ð minutes,
Ð year,
Ð month,
Ð day,
Ð unit of temperature (degrees Celsius or Fahrenheit).Pressing button 2alters the value of the parameter selected. Press and hold for
rapid advance (return to start after the last possible value). After 7 seconds with no action, the main display returns; the modified data are now recorded. Note: Pressing button 2briefly displays the outside temperature for a few
seconds.

24-02-2003
YOUR 206 IN DETAIL
36
Setting the parameters Press and hold button 1for two seconds to access the settings. The data
flashes, indicating it is ready to be modified. Then, individual presses on button 1allow you to scroll through the various data
in the following sequence:
Ð language in which the information is displayed,
Ð unit of distance (kms or miles),
Ð unit of temperature (degrees Celsius or Fahrenheit),
Ð time format (12 then 24 hour mode),
Ð hour,
Ð minutes,
Ð year,
Ð month,
Ð day.Pressing button 2allows you to change the data selected. Maintain the pressure
for rapid scrolling.After 7 seconds without moving, the main display returns; the modified data are now recorded.
DISPLAY B This enables the following informa- tion to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (this flashes when there is a risk of ice),
Ð the radio displays,
Ð a door check. The display shows you, by means of a graphic, whether a door is open.
Ð warning messages (e.g. ''battery charge low'') or information mes-sages (e.g. "fuel level low''), dis-
played temporarily. These can becleared by pressing button 1or 2,
Ð the trip computer.

24-02-2003
YOUR 206 IN DETAIL37
DISPLAY C This enables the following informa- tion to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (this flashes when there is a risk of ice),
Ð the radio displays,
Ð a door check. The display shows you, by means of a graphic, whether a door is open, Ð the warning messages (e.g. "fuel level low''), displayed temporarily. These can
be cleared using the remote control,
Ð the trip computer (see corresponding section),
Ð the satellite navigation system (see corresponding section). Setting the parameters
The remote control allows you to access the settings. Accessing the different menus is described in the section ''Satellite Navigation System''.

24-02-2003
AUDIO RB3
YOUR 206 IN DETAIL
40
Stalk movement
Function
1 - Press (behind) Increase volume
2 - Press (behind) Decrease volume
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound by pressing any button
3 - Press Automatic search of higher frequencies (radio)
Selection of the next track (CD)
4 - Press Automatic search of lower frequencies (radio)
Selection of the previous track (CD)
5 - Press the end Change of source (radio/cassette/CD changer)
6 - Rotation Selection of next station stored in memory (radio) - Selection of next CD
(clockwise)
7 - Rotation Selection of previous station stored in memory (radio) - Selection of previous CD
(anti-clockwise)

24-02-2003
YOUR 206 IN DETAIL41
Button
Function
A Radio on/off.
BÐDecrease volume.
C+Increase volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
ETATraffic information priority on/off.
F Press fully: cassette rewind.
G Press fully: cassette fast forward.
F+G jk Press half way: reversal of direction of play of the cassette.
jj kk Press fully: ejection of the cassette.
H Increase of the functions associated with button J.
I Decrease of the functions associated with button J.
J Adjustment of bass, treble, loudness, sound distribution and automatic
volume correction.
K SRC Selection of source: radio, cassette or CD changer.
Press for more than 2 seconds: CD shuffle.
L kk Automatic search of higher frequency.
Selection of next CD track.
M MAN
Manual/automatic operation of buttons Land Nin radio mode.
N jj Automatic search of lower frequency.
Selection of previous CD track.
O BND Selection of FM1, FM2, FMast and AM wavebands.
ASTPress for more than 2 seconds: automatic storing of stations in the memory (autostore).
1 to 6 Selection of station stored in the memory.
Press for more than 2 seconds: storing of a station in the memory.Selection of a CD changer disc.

24-02-2003
GENERAL FUNCTIONSOn/off With the ignition key in the accessories or ignition on position, press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ignition being switched on.
Anti-theft systemThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Press button Cto increase the volume, or button Bto decrease it.
Continuous pressure on buttons Band Callows a gradual adjustment of the volume.
AUDIO SETTINGS Press button Jseveral times in succession to access the bass (BASS), treble (TREB), loudness (LOUD),
fader (FAD) , balance (BAL)and automatic volume correction.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing button J
after configuration of the automatic volume correction. Note: bass and treble settings are specific to each source. It is possible to set them differently for radio,
cassette (RB3), CD (RD3) and CD changer.
YOUR 206 IN DETAIL
44

24-02-2003
Adjusting the bassWhen "BASS" is displayed, press button Hor Ito vary the setting.
Ð "BASS Ð9" for a minimum bass setting,
Ð "BASS 0" for a normal setting,
Ð "BASS +9" for a maximum bass setting.
Adjusting the treble When "TREB" is displayed, press button Hor Ito vary the setting.
Ð "TREB Ð9" for a minimum treble setting,
Ð "TREB 0" for a normal setting,
Ð "TREB +9" for a maximum treble setting.
Adjusting the loudnessThis function automatically emphasises bass and treble tones. Press button Hor Ito switch the function on or off.
Adjusting the front/rear sound distribution (Fader) When "FAD" is displayed, press button Hor I.
Button Hincreases the volume in the front.
Button Iincreases the volume in the rear.
Adjusting the right/left sound distribution (Balance)When "BAL" is displayed, press button Hor I.
Button Hincreases the volume on the right-hand side.
Button Iincreases the volume on the left-hand side.
Automatic volume correctionThis function enables the volume to be automatically adjusted depending on the level of noise produced by the speed of the vehicle. Press buttons Hor Ito switch the function on or off.
YOUR 206 IN DETAIL 45