PEUGEOT 4007 2012 Service Manual

1
INSTRUMENTS and CONTROLS
MONOCHROME SCRCHROME SCREEN

This provides the following information:


- the time,

- audio system information (refer to
the "Audio and Telematics" section).



Setting the time

The digital clock can be set in automatic
mode
or in manual mode
.


Selecting the Setting

Select the automatic mode
or the
manual mode
as follows:


)
Press button A
"PWR" to switch on
the audio system.

)
Access the setting mode by press-
ing button B
"TUNE" for approxi-
mately 2 seconds.

)
Press button B
"TUNE" several
times to scroll through the various
menus and select the CT menu

(clock time).
The order of the menus is the
following: AF/CT/REG/TP-S/PTY
display language/SCV/PHONE/
Functions setting mode OFF.
Automatic mode
This mode permits automatic setting
of the local time using the signal from
RDS stations.
The symbol "CT"
appears on the
screen.

Manual mode
This mode permits manual setting of
the time using the audio equipment but-
tons.
It can also be used when the "Automatic
mode" displays an inaccurate time,
when the local RDS stations are broad-
casting from a different time zone.

1
INSTRUMENTS and CONTROLS
Set the time using the buttons as indi-
cated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to
zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.


)
After setting the time, press the
DISP
button; the time display stops
fl ashing.


Manual mode

Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations. The digital clock does not dis-
play seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the bat-
tery is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.

1
INSTRUMENTS and CONTROLS
COLOUR SCREENCOLOUR SCREEN

This permits display of the following
main menus: On the control panel, press button B
(SET)
to access the "Settings"
screen
and select:


- "Display Off"
to switch off the dis-
play,

- "Sound control"
for the sound dis-
tribution or volume, the type of music and the sound fi eld (surround),

- "Picture control"
to set the colour,
the intensity, the brightness, the
contrast and the level of black,

- "System"
to change the time zone,
the language, the units and other
settings,

- "Wide Screen"
to change the size
of the DVD picture to 4/3 format,
wide screen mode, centred wide
screen mode or enlargement,

- "Equipment"
to set certain equip-
ment offered in the vehicle,

- "Colour Contrast"
to select the
contrast of the display in relation
to the ambient light (Day, Night or
Auto),

- "TP standby"
to activate or deacti-
vate the traffi c information.

"Audio-video" menu
"Navigation-guidance" menu
On the control panel, press button A
(MODE)
to access the "AV mode"

screen and select:


- radio (FM, MW, LW),

- CD (audio, MP3 or WMA),

- Music Server,

- DVD.
"Settings" menu
On the control panel, press button C
(MENU)
to access the "Menu"
screen
and select:


- "Address/Junction"
to search for
a location using the address or the
name of the street,

- "POI name"
to search for a location
using the name of a point of interest
(POI),

- "Advanced search"
to search for a
location using an advanced search
based on a POI,

- "Previous 20"
to search for a loca-
tion using one of the 20 previous
destinations,

- "Address book"
to search for a lo-
cation using a stored address,

- "Home"
to navigate to your home
address,

- "Navigation settings"
to set func-
tions linked with the navigation,

-
"Navigation tools"
to access the
basic information or a pre-set demon-
stration.


The "CD" and "DVD" buttons
are active if you insert a CD or
DVD in the player.

1
INSTRUMENTS and CONTROLS

Setting the time

The digital clock is set automatically
.
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.


)

On the control panel, press button B

(SET) to access the "Settings"
menu.


)
On the touch screen, press button B

to access the "System"
menu.
The system settings screen is dis-
played.
"Info" menu
On the control panel, press button D
(INFO)
to access the "Info"
screen and
consult:


- "Support info"
to display the soft-
ware and data versions,

- "Vehicle position"
to display the
GPS location of the vehicle,

- "Calendar"
to make a note of
events, birthdays, etc.,

- "Journey"
to display the average
speed, fuel consumption, distances
and driving time,

- "Environment"
to display the alti-
tude, the atmospheric pressure, the
exterior temperature (the ice symbol
is displayed if there is a risk of ice),

- "Air conditioning"
to display the
information relating to the air condi-
tioning,

- "Mobile phone"
to enter a number,
delete a character, make or receive
a call.

"Route" menu
On the control panel, press button E
(NAVI)
to access the "Route Menu"

screen and select:


- "Detour"
to make a detour through
a specifi ed region,

- "Itinerary"
to change the route,

- "View route"
to display a route in
different ways,

- "Delete route"
to delete a route,

-
"Nearby POI"
to search for the
POIs in the surrounding area.

1
INSTRUMENTS and CONTROLS


1.
RDS Auto Correct:

Activate/deactivate automatic ad-
justment.

2.
GMT/GMT+1/GMT+2

Select the time zone.

3.
Summer Time:

Summer time On/Off.


)
Press button D
to confi rm and re-
turn to the previous menu.

)
Press button C
to access the "Time"
menu .

You must deactivate automatic
adjustment (RDS Auto Correct)
to change the time zone and
summer time settings.
On each screen, you can return
to the previous screen by press-
ing button D "Return"
.

Once this menu has been selected, you
can access the following functions: LIGHTING RHEOSTAT
With the lighting on or off, press the but-
ton to change the intensity of the light-
ing of the instruments and controls in
"day" or "night" mode.
When the lighting reaches the maxi-
mum setting, press again to change to
the minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF. An audible signal is heard and the
intensity of the lighting increases
each time the button is pressed.
System for manual adjustment of the
brightness of the instruments and con-
trols in relation to the exterior bright-
ness.

2
COMFORT
For even air distribution, take care not
to obstruct the exterior air intake grille
located at the bottom of the windscreen,
the vents, the air outlets under the front
seats and the air extractor located be-
hind the fl aps in the boot. The water formed by the air conditioning
condensation is discharged via an open-
ing provided for this purpose. Therefore,
a puddle of water may form underneath
the vehicle when stationary.
If the system does not produce cold air,
do not use it and have it checked by a
PEUGEOT dealer or a qualifi ed workshop.
AUTOMATIC REGULATION OF ON OF
THE DIGITAL AIR CONDITIONING

Do not cover the temperature and
humidity sensor 2
and the sunshine
sensor 7
.
They are required for regulation of the
air conditioning.

Advice on operation

In hot weather, in order to obtain
intense ventilation, it is advis-
able to use vents 1
and 4
only.
If, when the vehicle has been
parked in the sun for a long time,
the interior temperature remains
very high, fi rst ventilate the pas-
senger compartment for a few
minutes. Switch off the air conditioning
when the climatic conditions
permit. Use of the automatic regulation of the
air conditioning is recommended. It per-
mits automatic and optimised control of
all of the following functions: air fl ow,
passenger compartment temperature
and air distribution, by means of various
sensors (ambient temperature, interior
temperature, sunshine), so preventing
the need for you to change your set-
tings other than the value displayed. In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient in hot weather), switch-
ing off the air conditioning saves engine
power and therefore improves the tow-
ing capacity.
Close the windows to benefi t from the
full effectiveness of the air conditioning.
Ensure that the passenger compart-
ment fi lter is in good condition. Have
the fi lter elements replaced periodically.
If you drive in a dusty environment, re-
place it twice as often.
The air conditioning system does not
contain chlorine and is not harmful to
the ozone layer.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in good working order.

1.
Central vents.

2.
Temperature sensor.

3.
Air outlet to passenger footwells.

4.
Side vents.

5.
Front window demisting/defrosting
vents.

6.

Windscreen demisting/defrosting vents.


7.
Sunshine sensor.

2
COMFORT

2
COMFORT
AUTOMATIC AIR
CONDITIONING

Automatic operation


)
Set the temperature control dial 1
to
the temperature required.

)
Place the air fl ow control dial 2
in
the "AUTO"
position.

)
Place the air distribution adjustment
dial 3
in the "AUTO"
position. When the engine is cold, to avoid
an excessive distribution of cold
air, the ventilation will reach its
optimum level gradually.
On entering the vehicle, the in-
terior temperature may be much
colder (or warmer) than the
comfort temperature. There is
no need to change the tempera-
ture displayed in order to reach
the comfort required rapidly.
The automatic regulation of the
air conditioning will operate to
correct the temperature difference
as quickly as possible.


1.
Temperature adjustment

2.
Air fl ow adjustment

3.
Air distribution adjustment

4.
Intake of exterior air/Recirculation of
interior air

5.
Air conditioning On/Off

6.
Rear screen demist/defrost
In automatic mode:


)
when the temperature is set to maxi-
mum (Rapid heating), the intake of
exterior air is activated and the air
conditioning stops.

)
when the temperature is set to mini-
mum (Rapid cooling), the air re-
circulation is activated and the air
conditioning operates.
The system controls the air distribu-
tion, the fl ow, the temperature and the
air intake to ensure the level of comfort
selected and adequate air circulation in
the passenger compartment. No further
action on your part is required.

2
COMFORT

Manual operation
It is possible to set one or more func-
tions manually while leaving the other
functions in automatic mode.

Switching to manual mode may result
in discomfort (temperature, humidity,
odour, condensation) and does not of-
fer optimum comfort.

Temperature adjustment (1)
Air fl ow adjustment (2)


)
Turn the dial to the
right to increase the
air fl ow or to the left to
decrease it.


)
Turn the temperature
control dial to the right
to increase the tem-
perature and to the left
to decrease it.


)
Place the dial in the
position required to di-
rect the air towards:
To avoid condensation and dete-
rioration of the quality of the air
in the passenger compartment,
ensure that a suffi cient fl ow of
air is maintained. the central and side vents,
the central and side vents and
the footwells,
the footwells,
the windscreen, the side
windows and the footwells,
the windscreen and the side
windows.
The air distribution can be adapted by
placing the adjustment dial in the inter-
mediate positions.
Air distribution adjustment (3)

2
COMFORT

Air conditioning On/Off (5)


)
Press button 5
to activate the air
conditioning.
The indicator lamp comes on.
Intake of exterior air/
Recirculation of interior air (4)

This function insulates the passenger
compartment from exterior odours and
smoke.


)
Press button 4
to select the air in-
take mode.
When the indicator lamp on button 4
is
off, the exterior air intake function is on.
When the indicator lamp on button 4
is
on, the intake of exterior air is off and
the system is in air recirculation mode.

Do not drive for long periods in
interior air recirculation mode,
except in truly exceptional atmo-
spheric conditions.
Personalisation of the Exterior
air intake/Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.

Personalisation of the Air
Conditioning On/Off function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to activate
or deactivate the air conditioning at
any time.
The settings are retained, even
after switching off the ignition.
Changing the status
Press the Air intake/Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator lamp fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator lamp fl ashes three times.

Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the "AUTO" position, the Air intake/
Interior air recirculation function is also
controlled automatically.

Automatic control inactive
Even if the air distribution adjustment
dial and the air fl ow adjustment dial are
placed in the "AUTO" position, the Air
intake/Interior air recirculation function
is no longer controlled automatically.
Changing the status
Press the Air Conditioning On/Off button
for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator lamp fl ashes three times.

When the status changes from inactive
to active, two bleeps are heard and the
indicator lamp fl ashes three times.

Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed in
the "AUTO" position, or if the tempera-
ture control dial is set to the minimum
temperature, the air conditioning system
is controlled automatically.

Automatic control inactive
The air conditioning system is no longer
controlled automatically.