engine PONTIAC G8 2009 Owners Manual

Page 61 of 356

L(Vehicle Locator/Panic Alarm):
Press and release one time to locate
the vehicle. The exterior lamps ash
and the horn chirps.
Press and hold
Lfor at least
two seconds to sound the panic
alarm. The horn sounds and the turn
signals ash until
Lis pressed
again or the key is placed in the
ignition and turned to ON/RUN.
/(Remote Vehicle Start):
For vehicles with this feature,
press to start the engine from
outside the vehicle using the
RKE transmitter. SeeRemote
Vehicle Start on page 2-6for
additional information.
Personal Identity Keys
This system stores electronic
settings for two different keys.
The settings are stored when a
personal identity key is removed
from the ignition and recalled when
Qon the RKE transmitter is
pressed. For information on storing
climate control settings, radio
settings and trip computer settings,
see “Personal Identity Memories”
underRadio(s) on page 6-3,
“Ignition Keys” underClimate
Control System on page 7-1and
“Trip Computer” underDIC Vehicle
Customization on page 4-31.
Programming Transmitters
to the Vehicle
Only RKE transmitters programmed
to this vehicle will work. If a
transmitter is lost or stolen, a
replacement can be purchasedand programmed through your
dealer/retailer. When the
replacement transmitter is
programmed to this vehicle, all
remaining transmitters must also be
reprogrammed. Any lost or stolen
transmitters will no longer work once
the new transmitter is programmed.
Battery Replacement
Replace the battery if the Replace
Battery in Remote Key message
displays in the DIC. See “Replace
Battery in Remote Key” under
DIC Warnings and Messages on
page 4-26.
The battery is not rechargeable.
See your dealer/retailer to replace
the battery.
Keys, Doors and Windows 2-5

Page 62 of 356

Remote Vehicle Start
Your vehicle may have this feature
which allows you to start the
engine from outside the vehicle.
/(Remote Vehicle Start):
This button will be on the RKE
transmitter if you have remote start.
To enable and disable remote
start, see “Remote Start” under
DIC Vehicle Customization on
page 4-31.
Vehicles with an automatic climate
control system will default to a
heating or cooling mode depending
on the outside temperature during
a remote start. When the key
is turned to ON/RUN, the climate
control system will turn on at
the setting the vehicle was set to
when the vehicle was last turned off.Laws in some local communities
may restrict the use of remote
starters. For example, some laws
may require a person using remote
start to have the vehicle in view
when doing so. Check local
regulations for any requirements on
remote starting of vehicles.
If your vehicle is low on fuel,
do not use the remote start feature.
The vehicle may run out of fuel.
If your vehicle has the remote start
feature, the RKE transmitter
functions will have an increased
range of operation. However,
the range may be less while the
vehicle is running.
There are other conditions which
can affect the performance of
the transmitter, seeRemote Keyless
Entry (RKE) System on page 2-3
for additional information.Starting the Engine Using
Remote Start
To start the engine using the remote
start feature:
1. PressQon the RKE transmitter.
2. Press and hold
/for about
two seconds. The turn signal
lamps will briey ash to conrm
the vehicle has been started.
The parking lamps will turn
on and remain on as long as the
engine is running. The vehicle’s
doors will be locked.
3. After entering the vehicle during
a remote start, insert and turn
the key to ON/RUN to drive
the vehicle.
After a remote start, the engine
will automatically shut off
after 10 minutes unless a time
extension has been done or
the vehicle’s key is inserted into
the ignition switch and turned
to ON/RUN.
2-6 Keys, Doors and Windows

Page 63 of 356

Extending Engine Run Time
To extend the engine run time by
10 minutes, repeat Steps 1 and 2
while the engine is still running.
The engine run time can only
be extended if it is the rst remote
start since the vehicle has been
driven. Remote start can be
extended one time.
If the remote start procedure is used
again before the rst 10 minute
time frame has ended, the rst
10 minutes will immediately expire
and the second 10 minute time
frame will start.
For example, if the lock button and
then the remote start buttons
are pressed again after the vehicle
has been running for ve minutes,
10 minutes are added, allowing
the engine to run for a total of
15 minutes.A maximum of two remote starts or
remote start attempts are allowed
between ignition cycles.
After your vehicle’s engine has been
started two times using the remote
start button, the vehicle’s ignition
switch must be turned to ON/RUN
and then back to LOCK/OFF
using the key before the remote
start procedure can be used again.
Shutting the Engine Off After
a Remote Start
To manually shut off the engine
after a remote start, do any of the
following:
Press/until the parking lamps
turn off.
Turn on the hazard warning
ashers.
Insert the vehicle’s key into the
ignition switch and turn the
switch to ON/RUN and then
back to LOCK/OFF.Conditions in Which Remote Start
Will Not Work
The remote vehicle start feature
will not operate if any of the
following occur:
The vehicle’s key is in the ignition.
The vehicle’s hood or doors are
not closed.
The hazard warning ashers
are on.
There is an emission control
system malfunction.
The engine coolant temperature
is too high.
The oil pressure is low.
Two remote vehicle starts have
already been used. The maximum
number of remote starts or remote
start attempts between ignition
cycles with the key is two.
The vehicle is not in P (Park).
Keys, Doors and Windows 2-7

Page 66 of 356

Trunk
{CAUTION
It can be dangerous to drive
with the trunk lid open because
carbon monoxide (CO) gas
can come into your vehicle.
You cannot see or smell CO.
It can cause unconsciousness
and even death. If you must
drive with the trunk lid open or
if electrical wiring or other
(Continued)
CAUTION (Continued)
cable connections must pass
through the seal between the
body and the trunk lid:
Make sure all other windows
are shut.
Turn the fan on your heating
or cooling system to its
highest speed and select the
control setting that will force
outside air into your vehicle.
See Climate Control System.
If you have air outlets on or
under the instrument panel,
open them all the way.
SeeEngine Exhaust on page 8-14.
Remote Trunk Release
To open the trunk from the outside
the vehicle, press the
Vbutton
on the Remote Keyless Entry (RKE)
transmitter.
From inside the vehicle, press the
Vbutton located in the glove box.
The trunk can only be opened
while the vehicle is in PARK (P),
and when the doors are unlocked.
Emergency Trunk Release
Handle
Notice:Do not use the
emergency trunk release handle
as a tie-down or anchor point
when securing items in the trunk
as it could damage the handle.
The emergency trunk release
handle is only intended to aid
a person trapped in a latched
trunk, enabling them to open
the trunk from the inside.
2-10 Keys, Doors and Windows

Page 68 of 356

Immobilizer Operation
This vehicle has a passive
theft-deterrent system.
The system is automatically armed
when the key is removed from
the ignition.
The system is disarmed when the
key is turned to ON/RUN.
You do not have to manually arm or
disarm the system.
The key uses a transponder that
matches an immobilizer control unit
in the vehicle and automatically
disarms the system. Only the correct
key starts the vehicle. The vehicle
may not start if the key is damaged.
If the vehicle does not start:
Make sure the fold away key is
fully extended.
Avoid attaching several keys with
the ignition key.
Avoid attaching keys from other
vehicles to the ignition key.
Do not attempt to start the
vehicle with a non-approved key.
Do not disassemble the key.
When trying to start the vehicle,
if the engine does not start, the key
may have a damaged transponder.
Turn the ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key.
If the engine still does not start,
the vehicle needs service.
See your dealer/retailer to service
the theft-deterrent system and
have a new key made.
The following procedure is for
programming additional keys only.
If all vehicle keys are lost or no
longer work, see your dealer/retailer.
A new key must be made prior to
programming.
A maximum of four keys can be
programmed for the vehicle.The key is purchased as two
sections: the key blade and
immobilizer section (A) and the
remote keyless entry and remote
start system section (B).
Do not join the two key sections
until programming is complete.
To program a new section (A):
1. Insert the original, already
programmed key into the
ignition and start the engine.
If the engine does not start,
see your dealer/retailer.
2. Remove the key from the ignition.
2-12 Keys, Doors and Windows

Page 74 of 356

Manually fold the mirrors inward to
prevent damage when going
through an automatic car wash.
To fold, push the mirror toward the
vehicle. Push the mirror outward,
to return to its original position.
Outside Convex Mirror
{CAUTION
A convex mirror can make things
(like other vehicles) look farther
away than they really are. If you
cut too sharply into the right lane,
you could hit a vehicle on the
right. Check the inside mirror or
glance over your shoulder before
changing lanes.
The passenger side mirror is convex
shaped. A convex mirror’s surface
is curved so more can be seen from
the driver’s seat.
Sunroof
The sunroof control is located
between the sun visors. It works
when the ignition is in ON/RUN.
The sunroof will not operate after
the engine is turned off.
From the closed position
9, turn
the control clockwise to one of the
six open positions. The sunshade
opens with the sunroof.
Tilt the sunroof by turning the
control counter-clockwise.
Obstruction Detection
When the sunroof encounters
an obstruction while closing,
it immediately returns to the fully
open or tilt position. The sunroof will
not move again until the control is
pressed upward, or a different
position is selected.
2-18 Keys, Doors and Windows

Page 77 of 356

Instruments and
Controls
Instrument Panel
Overview
Instrument Panel
Overview...........................4-2
Hazard Warning
Flashers............................4-4
Horn...................................4-4
Tilt Wheel...........................4-4
Turn Signal/Multifunction
Lever................................4-4
Cruise Control....................4-5
Turn and Lane-Change
Signals.............................4-7
Headlamp High/
Low-Beam Changer..........4-7
Windshield Wipers..............4-8
Windshield Washer.............4-8
Accessory Power
Outlet(s)............................4-9
Warning Lights, Gages,
and Indicators
Warning Lights, Gages,
and Indicators.................4-10
Instrument Panel
Cluster............................4-11
Speedometer....................4-12
Tachometer.......................4-12
Safety Belt Reminders......4-12
Airbag Readiness Light.....4-13
Passenger Airbag
Status Indicator...............4-14
Voltmeter Gage.................4-15
Charging System Light......4-15
Brake System Warning
Light................................4-15
Antilock Brake System
(ABS) Warning Light.......4-16
Engine Coolant
Temperature Gage..........4-17
Tire Pressure Light...........4-17
Malfunction
Indicator Lamp................4-18
Security Light....................4-20
Fog Lamp Light................4-20
Highbeam On Light...........4-20
Daytime Running
Lamps (DRL)
Indicator Light
.................4-21
Door Ajar Light.................4-21
Oil Pressure Gage............4-21
Fuel Gage........................4-21
Driver Information
Center (DIC)
Driver Information
Center (DIC)...................4-22
DIC Operation and
Displays..........................4-22
DIC Warnings and
Messages........................4-26
DIC Vehicle
Customization..................4-31
OnStar®System
OnStar®System................4-35
Instruments and Controls 4-1

Page 81 of 356

Cruise Control
For vehicles with cruise control,
the lever is located on the left side
of the steering wheel.
The cruise control maintains the
vehicle’s speed without having your
foot on the accelerator pedal.
The cruise control only works at
speeds above 21 mph (33 km/h)
(V6 engines) or above 24 mph
(38 km/h) (V8 engines).
{CAUTION
Cruise control can be dangerous
where you cannot drive safely at
a steady speed. So, do not use
your cruise control on winding
roads or in heavy traffic.
Cruise control can be dangerous
on slippery roads. On such roads,
fast changes in tire traction can
cause excessive wheel slip, and
you could lose control. Do not use
cruise control on slippery roads.Setting Cruise Control{CAUTION
If you leave your cruise control on
when you are not using cruise,
you might hit a button and go into
cruise when you do not want to.
You could be startled and even
lose control. Keep the cruise
control switch off until you want to
use cruise control.
1. Press the
OQbutton at the
end of the cruise control lever.
The CRUISE ON light comes on
in the instrument panel cluster.
SeeInstrument Panel Cluster on
page 4-11.
2. Get up to the desired speed.
3. Turn the band down to SET−and
then release it. The CRUISE
ACTIVE light comes on in
the instrument panel cluster.
4. Take your foot off the accelerator
pedal.
Instruments and Controls 4-5

Page 82 of 356

If the vehicle is in cruise control
and the Electronic Stability
Program (ESP) becomes active,
the cruise control automatically
disengages. SeeElectronic
Stability Program on page 8-19.
When road conditions allow the
cruise control can be used again.
Resuming a Set Speed
If the cruise control is set at a
desired speed and then the brakes
are applied or the
OQbutton
is pressed once, the cruise control
shuts off.
Once the vehicle speed is
21 mph (33 km/h) (V6 engines)
or 24 mph (38 km/h) (V8 engines) or
greater, turn the band briey to
RES+ position. The vehicle returns
to the previously set speed and
stays there.Increasing Speed While Using
Cruise Control
There are two ways to go to a
higher speed:
Turn theIband up to the
RES+ position. Hold it there until
the desired speed is reached,
then release it.
To increase the vehicle speed in
very small amounts, turn the
band to RES+ briey and then
release it. Each time this is done,
the vehicle goes about 1 mph
(1.6 km/h) faster.
Reducing Speed While Using
Cruise Control
There are two ways to reduce the
vehicle speed while using cruise
control:
Turn theIband down to the
SET−position. Hold it there
until the lower speed desired is
reached, then release it.
To slow down in very small
amounts, turn the band to SET−
briey and then release it.
Each time this is done, the
vehicle will go about 1 mph
(1.6 km/h) slower.
Passing Another Vehicle While
Using Cruise Control
Use the accelerator pedal to
increase the vehicle speed.
When you take your foot off the
pedal, the vehicle slows down to
the cruise control speed set earlier.
Using Cruise Control on Hills
How well the cruise control works
on hills depends upon the vehicle
speed, load, and the steepness of
the hills.
When going up steep hills,
you might have to step on the
accelerator pedal to maintain the
vehicle speed.
4-6 Instruments and Controls

Page 86 of 356

Warning Lights,
Gages, and Indicators
Warning lights and gages can
signal that something is wrong
before it becomes serious enough
to cause an expensive repair or
replacement. Paying attention to
the warning lights and gages could
prevent injury.
Warning lights come on when
there may be or is a problem with
one of the vehicle’s functions.
Some warning lights come on briey
when the engine is started to indicate
they are working.Gages can indicate when there may
be or is a problem with one of the
vehicle’s functions. Often gages and
warning lights work together to
indicate a problem with the vehicle.
When one of the warning lights
comes on and stays on while driving,
or when one of the gages shows
there may be a problem, check the
section that explains what to do.
Follow this manual’s advice.
Waiting to do repairs can be costly
and even dangerous.
4-10 Instruments and Controls

Page:   1-10 11-20 21-30 31-40 41-50 ... 120 next >