RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work Workshop Manual

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
13010R1
CAB11540R1
F
5 2
CAC11541R7
G
57
CAS13028R2
H
5
4
3
42-15

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
13005R3
CAP11696-1R4
I
3 2
5
42-16

UPPER FRONT STRUCTURE
Wheel arch
42F
PRB4213
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the cowl side pa-
nel (pillar lining) for a frontal impact.
It also requires the replacement of the cowl side
panel upper reinforcements (pillar lining), and
the use of the repair bench.
In the operation below there are only descriptions
of the joints specific to the part concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- engine mounting height adjuster (right hand
side),
- engine support plate (right hand side),
- wheel arch ,
- shock absorber cup ,
- shock absorber cup height adjuster ,
- ABS mounting (right hand side),
- injection unit and impact sensor mounting
(left hand side).
JOINTS WITH :
Plenum chamber
Side member closure panel
Front side member
Front end lower cross member
PARTS CONCERNED (thickness in mm):
1Shock absorber cup height adjuster 1
2Engine mounting height adjuster 1.5
3Engine mounting reinforcement 1.5
4Shock absorber cup 2
5Plenum chamber 1
6Side member closure panel 1
7Front side member, front section 1.5
8Front side member, rear section 2.5
9Front wheel arch 1
10Front end lower cross member 1.5
11Injection unit and impact sensor
mounting (left hand side) 2
42-17

UPPER FRONT STRUCTURE
Wheel arch
42F
13009R
A
CAQ11697R5
B
9
7
CAI11550-2R5
C
976 10
9
CAR11700R5
42-18

UPPER FRONT STRUCTURE
Wheel arch
42F
12895R1
CAA11536-1R3
D
3
2
CAA11538-1R3
E
1
7
CAS13029R1
F
1
7
8
42-19

UPPER FRONT STRUCTURE
Wheel arch
42F
13005R1
CAA11536-4R2
G1
18
CAA11536R2
G
18
CAA11537-2R5
H1
16
CAA11537-1R5
H
16
42-20

UPPER FRONT STRUCTURE
Wheel arch
42F
CAB11539-1R8
I
1
7
CAE11546R7
J
1
7 6
CAS13028R1
K
9
7
6
CAA11538R7
L
92
13005R2
42-21

UPPER FRONT STRUCTURE
Wheel arch
42F
13000R
CAA11536R8
M
1
5
CAS13024-1R3
N
4
5 1
13007R
42-22

UPPER FRONT STRUCTURE
Wheel arch
42F
13010R2
CAA11538R8
O
5
11
CAS13028R2
P
9
6 7
42-23

UPPER FRONT STRUCTURE
Plenum chamber
42G
PRB4214
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of :
- the wheel arch for a frontal impact,
- cowl side panel for a side impact.
This operation may be carried out partially (see
diagram and method below).
The Parts Department only provides chambers of
the (1) "air conditioning" type, as a result, the
closure panel must also be ordered (2).
In the following operation there are only descrip-
tions of the joints specific to the part concerned.
Information concerning other parts is dealt with
in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 Plenum chamber
Part assembled with :
- bonnet lock mounting,
- windscreen wiper motor mounting.
2 Partition closure panel.
JOINTS WITH :
Wheel arch
Injection unit and impact sensor mounting (left
hand side)
Bulkhead
Pillar lining (cowl side panel)
Windscreen aperture lower cross member
PARTS CONCERNED (thickness in mm) :
1Plenum chamber 1
2Shock absorber cup height adjuster 1
3Shock absorber cup 2
4Injection unit and impact sensor
mounting (left hand side) 2
5Bulkhead 1
6Cowl side panel (pillar lining) 1.5
7Windscreen wiper mounting 1.5
8Windscreen aperture lower cross
member 1.2
or
42-24