RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work Workshop Manual

UPPER SIDE STRUCTURE
Centre pillar / sill panel
43D
13230R
CAI11550R6
F
12 3
CAI11550R6
G
15 3
CAI11550R1
H
1
5
3
CAI11550R1
I
1
2
3
43-17

UPPER SIDE STRUCTURE
Centre pillar / sill panel
43D
13229R
or
CAS13033R8
J
1
1
43-18

UPPER SIDE STRUCTURE
Centre pillar lower reinforcement / door pillar
43E
PRB4315
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre pillar
for a front side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
On the part supplied by the Parts Department,
the pillar upper reinforcement will need to be un-
picked.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with seat belt mounting nut.
CAA11538-1R4
A
12
CAB11539R6
B
12
43-19

UPPER SIDE STRUCTURE
Centre pillar lower reinforcement / door pillar
43E
JOINTS WITH:
Sill panel closure panel
Centre pillar upper reinforcement
Body side lining
Sill panel reinforcement
NOTE : welding of the joint with the body side
lining will be carried out when the centre pillar is
refitted.
PARTS CONCERNED (thickness in mm) :
1Centre pillar lower reinforcement 1.2
2Centre pillar upper reinforcement 1.2
3Body side lining 0.8
4Sill panel reinforcement 1.2
43-20

UPPER SIDE STRUCTURE
Centre pillar lower reinforcement / door pillar
43E
13355R1
CAA11538-1R4
A
12
CAI11550R8
B
1 2
3
43-21

UPPER SIDE STRUCTURE
Centre pillar lower reinforcement / door pillar
43E
13353R
CAA11537R2
C
1
4
CAE11546R7
D
1
3
5
CAF11547R4
E
1
5
3
CAA11536R6
F
1 3
43-22

UPPER SIDE STRUCTURE
Sill panel reinforcement
43F
PRB4316
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the sill panel for
a side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
LIST OF JOINTS :
Sill panel closure panel
Centre pillar lower reinforcement
Body side lining
Front pillar reinforcement (identical to the centre
pillar reinforcement)
PARTS CONCERNED (thickness in mm) :
1Sill panel reinforcement 1.2
2Sill panel closure panel 1.2
3Centre pillar lower reinforcement 1.2
43-23

UPPER SIDE STRUCTURE
Sill panel reinforcement
43F
13353R1
CAA11537-1R2
A
13
CAB11539-1R3
B
12
CAB11539-1R8
C
1
2
43-24

UPPER SIDE STRUCTURE
Left hand side sill panel
43G
PRB4317
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
This part can be partially replaced (see diagram
and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
This part may be replaced in two ways :
1 - Cut A-A (described below)
2 - Cut B-B (refer to operation N for the front pil-
lar)
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
or
LIST OF JOINTS :
Body side lining
Sill panel closure panel, rear section
Sill panel closure panel, front section
PARTS CONCERNED (thickness in mm) :
1Left hand side sill panel 0.8
2Body side lining 0.7
3Sill panel closure panel, rear section 1.2
4Sill panel closure panel, front section 1.2
43-25

UPPER SIDE STRUCTURE
Left hand side sill panel
43G
13219R
or
CAA11537-1R4
A
1
1
12
or1
2
CAV13468R3
B
2
3
or
1
2
CAS13033R5
C
1
or1
2 1
1
43-26