RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work Workshop Manual

UPPER SIDE STRUCTURE
Left hand side sill panel
13609R
43G
or
CAS13033R7
D
1
or
CAN11691R7
E
1
2
CAE11546-2R8
F
1 2 3
CAE11546-2R8
G
1 2 4 1
43-27

UPPER REAR STRUCTURE
Rear wing panel
44A
PRB4413
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
For the panel version, this part may be replaced in
two ways (see cuts marked on the diagram be-
low) :
1 - complete replacement with cut A.A
2 - partial replacement with cut B.B
At the end of the section there are special details
for the glazed version and for the version with
roof flap.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with sliding door rail units and
striker plate mounting.
JOINTS WITH :
Lights mounting side panel rain channel
Body side lining
Centre pillar reinforcement
PARTS CONCERNED (thickness in mm):
1Rear wing panel (right hand side) 0.8
2Rear wing panel lining
(right hand side) 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Centre rail mounting 1
7Stretcher lining 0.7
8Roof 0.7
9Centre pillar upper reinforcement 1.2
10Centre pillar reinforcement 1.2
11Sill panel rear closure panel 1.5
12Seat belt mounting reinforcement 1.2
13Roof flap rain channel 0.7
44-1

UPPER REAR STRUCTURE
Rear wing panel
44A
13226R1
or
CAS13033R1
A
11
CAI11550-2R1
B - C
1 9 2
44-2

UPPER REAR STRUCTURE
Rear wing panel
44A
13227R
CAI11550-2R1
D
1 7 2
CAQ11697R3
E
1 2
CAI11550-2R4
F
1 2
12
44-3

UPPER REAR STRUCTURE
Rear wing panel
44A
13229R1
or
CAS13033R1
G
11
CAE11546-2R7
H
1 11
2
CAE11546-2R4
I
11 1
2
44-4

UPPER REAR STRUCTURE
Rear wing panel
44A
13216R
CAB11540-1R1
J
13
CAB11540-1R7
K
1 5
13212R1
or
CAV13468R1
L
11
44-5

UPPER REAR STRUCTURE
Rear wing panel
44A
13356R
CAN11691R7
M
1
2
1
1
22
44-6

UPPER REAR STRUCTURE
Rear wing panel
44A
13218R1
GLAZED
VERSION
CAS13033R8
A
1or
1
CAS13033R8
A
1
1
13217R1
44-7

UPPER REAR STRUCTURE
Rear wing panel
44A
INTRODUCTION
Below there are special details for vehicles fitted
with a roof flap.
VERSION WITH
ROOF FLAP
13475R
CAC11541-1R6
A
1 13
CAC11541-1R6
B
1 5
44-8

UPPER REAR STRUCTURE
Side panel
44B
PRB4414
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
For the panel version, this part may be replaced in
two ways (see cuts on the diagram below) :
1 - complete with cut A.A on the upper section
2 - partial with cut B.B for the glazed version
At the end of the section there are also special de-
tails for the glazed version and the version with a
roof flap.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with sliding door rail units and
striker plate mounting.
JOINTS WITH :
Lights mounting side panel rain channel
Body side lining
Door pillar reinforcement
Wing panel stiffener spacer
PARTS CONCERNED (thickness in mm):
1Rear wing panel 0.8
2Rear wing panel lining 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Centre rail mounting 1
7Stretcher lining 0.7
8Roof 0.7
9Door pillar upper reinforcement 1.2
10Door pillar reinforcement 1.2
11Sill panel closure panel 1.5
12Roof flap rain channel 0.7
13Sill panel pillar reinforcement 1.2
14Wing panel stiffener spacer 0.7
15Wing panel stiffener 0.7
44-9