ABS RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Owner's Guide

17B-81V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF362
PRESENT OR
STOREDIGNITION COIL 2-3 CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after starting the engine and under the following conditions:
– engine running at idling speed
Special note:
For CC.1 and CO, the OBD warning light and level 1 fault warning light illuminate.
For CC.0, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
The D4D and K7M engines are equipped with a quadruple ignition coil module.
The K4M engine is equipped with 4 "pencil" type coils.
D4D and K7M engines
Check the cleanliness and condition of the injection computer connector, component code 120 and of the coil
connector, component code 778.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CV or 3CZ (for Clio II F 6) between components 120 and 778,
–3CW or 3CV (for Clio II F 6) between components 120 and 778.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check the supply of the ignition coil, component code 778 using a test light on connection 3NA.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1047 or 1016 (for Clio II F 6) and 778.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF362/V42_V05_DF362/V42_V06_DF362/V42_V14_DF362/V42_V16_DF362/V42_V18_DF362

17B-82V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF362
CONTINUED
K4M engine
Check the cleanliness and condition of the injection computer connector, component code 120, the pencil coil no.
2 connector, component code 1078 and the pencil coil no. 3 connector, component code 1079.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CP between components 120 and 1078 (for Logan, Sandero, Duster),
–3CH between components 120 and 1078 (for Thalia 2/Symbol 2),
–3CF between components 120 and 1078 (for Kangoo VLL),
–3CW between components 1078 and 1079.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the ignition coils, component code 1078 and 1079 using a test light on
connection 3NA of the injection relay, component code 1047 (for Logan, Sandero, Duster), on connection 3NA
of the fuel pump relay, component code 236 (for Kangoo VLL) or on connection 3N of the fuel pump relay,
component code 236 (for Thalia 2/Symbol 2).
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1079 and 1047 (for Logan, Sandero, Duster) or 236 for Kangoo VLL),
–3N between components 1079 and 236 (for Thalia 2/Symbol 2).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-92
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
V2 MR-376-X76-17B050$083.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF409
PRESENT OR
STOREDFUEL LEVEL SENSOR CIRCUIT1.DEF: Voltage too low
2.DEF: Voltage too high
NOTESSpecial notes:
OBD warning light comes on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
instrument panel connector, component code 247.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–47H between components 120 and 247,
–3NX between components 120 and 247,
–137C between components 120 and 247,
–31A between components 120 and 247.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF409/V42_V05_DF409/V42_V06_DF409/V42_V14_DF409/V42_V16_DF409/V42_V18_DF409
PETROL INJECTION
Fault finding – Interpretation of faults

17B-96V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
*TDC: Top Dead Centre
DF457
PRESENT OR
STOREDFLYWHEEL TARGET1.DEF: Component in bad condition
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine running, engine speed > 3500 rpm.
Special notes:
OBD warning light comes on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the TDC*
sensor connector, component code 149.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the TDC* sensor component code 149 between connections 3BL and 3BG on the
injection computer connector, component code 120.
If the resistance of the crankshaft position sensor is not between 175 X  295  or 200  X 270  (F4R
engine of Duster) (between 0°C and 40°C), replace the crankshaft position sensor (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Crankshaft position sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3BG between components 120 and 149,
–3BL between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Check the cleanliness and condition of the flywheel (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 10A, Engine and cylinder
block assembly, Flywheel: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF457/V42_V05_DF457/V42_V06_DF457/V42_V14_DF457/V42_V16_DF457/V42_V18_DF457

17B-99
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF532
PRESENT OR
STOREDALTERNATOR CHARGE SIGNAL1.DEF: Voltage too low
2.DEF: Voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes:
the OBD warning light is on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
–2K between components 103 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the check is correct, replace the alternator, component code 103 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 16A,
Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF532/V42_V05_DF532/V42_V06_DF532/V42_V14_DF532/V42_V16_DF532/V42_V18_DF532

17B-100
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF556
PRESENT OR
STOREDPEDAL/THROTTLE POSITION CONSISTENCY1.DEF: Signal incoherent
2.DEF: Detection of micro-cut
NOTESThe inlet throttle valve no longer operates.
Special notes:
For 1.DEF, the OBD and level 1 fault warning lights are illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the injection computer connector, component code 120 and the damper
valve connector, component code 1076 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Petrol injection
computer: Removal - Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJB between components 1076 and 120,
–3AJC between components 1076 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
V42_V04_DF556/V42_V05_DF556/V42_V06_DF556/V42_V14_DF556/V42_V16_DF556/V42_V18_DF556

17B-102
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF631
CONTINUED
Check the brake pedal switch connector, component code 160 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal
switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical
component controls, Brake pedal: Removal - Refitting).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring
Check fuse F03 (for Logan, Sandero, Duster), F4 (for Thalia 2/Symbol 2, Clio II F 6 or F16 (for Kangoo VLL) and
replace it if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–AP1 between components 160 and 1016 (for Logan, Sandero, Duster),
–AP10 between components 160 and 1016 (for Thalia 2/Symbol 2, Clio II F 6)
–AP10 between components 160 and 260 (for Kangoo VLL),
–5A between components 160 and 120,
–65A between components 160 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-123
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF884
PRESENT OR
STOREDADDITIONAL FUEL CIRCUIT PUMP RELAYCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for application to a stored fault:
The fault is declared present after running command
AC224 Additional fuel circuit pump relay.
See the Wiring Diagrams Technical Note for Logan, Sandero, Kangoo VLL.
Check the supply of the control circuit of the additional fuel supply pump relay with a test light by running command
AC224.
Check the cleanliness and condition of the connector of the additional petrol pump relay, component code 1639
and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–3ACK between components 1639 and 120,
–3FB between components 1639 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the power circuit of the additional fuel supply pump relay with a test light by running command
AC224. If the check is correct, replace the pump, component code 1639 (see MR 388 (Logan and Sandero) or
MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel pump of the additional fuel tank: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF884/V42_V05_DF884/V42_V06_DF884/V42_V14_DF884/V42_V16_DF884/V42_V18_DF884

17B-126
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF894
PRESENT OR
STOREDADDITIONAL FUEL CIRCUIT SOLENOID VALVECC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
For engines: K4M, K7M, D4D
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Kangoo VLL.
Check the connection and condition of the connector of the additional fuel circuit solenoid valve, component code
1640 and the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation, and absence of interference resistance on the following connections:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the solenoid valve using a test light, by running command AC217 Additional fuel circuit
solenoid valve.
Check the internal resistance of the solenoid valve, component code 1640 on the computer connector; its value
must be between: 12  < X  16  (Duster F4R engine) or 22  < X  30  (Duster K4M engine). If the resistance
is incorrect, replace the solenoid valve.
If the fault is still present, contact the Techline.
V42_V04_DF894/V42_V05_DF894/V42_V06_DF894/V42_V14_DF894/V42_V16_DF894/V42_V18_DF894
PETROL INJECTION
Fault finding – Interpretation of faults

17B-127
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF894
CONTINUED 1
For engines: F4R 404, 405, 408
NOTESThis fault corresponds to an electrical fault of the additional fuel circuit injector, which is
fitted directly on the throttle valve. It is not a solenoid valve fault.
See the Wiring Diagrams Technical Note for Duster.
Check the fitting and sealing of the additional fuel circuit injector
If there is leakage, replace the defective component (the injector inlet hose, the injector seal, the additional fuel
circuit injector).
Check the connection and condition of the connector of the additional fuel circuit injector, component code 1640
and the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and the absence of interference resistance on the following connections:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.