TOYOTA GR86 2022 Owners Manual (in English)

59
5
5-2. Apple CarPlay
Apps
5-2.Apple CarPlay
●Use an undamaged genuine USB
cable when using this function.
●Enable Apple CarPlay in the Apple CarPlay device’s restriction settings
before using this function.
1 Connect an Apple CarPlay
device to the USB port. ( P. 1 9 )
2 Check the confirmation mes-
sage, and then select “Yes”.
 The Apple CarPlay screen will be
displayed.
 If “Don’t show again.” is selected,
the confirmation message will
not be displayed again.
Select “Apple Ca rPlay” on the
home screen or the apps screen
( P.8, 9) to display the Apple
CarPlay screen.
Displays the application buttons.
Select to start the application.
Select to change the home
screen of Apple CarPlay.
*: The displayed screen will differ
depending on the connected Apple
CarPlay device.
■About the supported devices
This system compatible with iOS
13.2 or later are supported.
Whether a registered device con-
nects as an Apple CarPlay device
or an iPod/iPhone can be set.
This setting can be changed only if
“Don’t show again.” was selected
Apple CarPlay
Apple CarPlay can be used to
view Apple Maps, play music,
and place calls by connecting
an Apple CarPlay device to the
system. Supported applica-
tions can also be run.
 For details on the services or
the operations, check the
Apple CarPlay site
(https://www.apple.com/ios/
carplay/).
To use the Apple CarPlay appli-
cation, connect an Apple
CarPlay device to the USB
port.
When using the application,
read the precautions indicated
in “Before using applica-
tions”. ( P. 5 6 )
Connecting the Apple
CarPlay device
Overview
Control screen*
Selecting device to connect
to Apple CarPlay
A
B

605-2. Apple CarPlay
on the confirmation message dis-
played when an Apple CarPlay
device was connected.
1 Display the phone settings
screen. ( P. 2 4 )
2 Select “Apple CarPlay”.
3 Select “Device List”.
4 Select “Edit”.
5 Select for the desired Apple
CarPlay device.
6 Select “OK”.
This setting can be changed only if
“Don’t show again.” was selected
on the confirmation message dis-
played when an Apple CarPlay
device was connected.
1 Display the phone settings
screen. ( P. 2 4 )
2 Select “Apple CarPlay”.
3 Select “Device List”.
4 Select “Edit”.
5 Select next to the desired
device name.
6 Select “Yes”.
7 Select “OK”.
Deleting the Apple CarPlay
device

61
5
5-3. Android Auto
Apps
5-3.Android Auto
●Use an undamaged genuine USB
cable when using this function.
●To use this function, check to make
sure that your Android device is set to accept connection with a new vehicle.
●Depending on the model, the talkback volume of the voice recognition func-
tion of Android Auto may differ from
the volume setting of other functions. Set the volume to a level that is easy
to hear.
1 Connect an Android Auto device
to the USB port. ( P. 1 9 )
2 Check the confirmation mes-
sage, and then select “Yes”.
 The Android Auto screen will be
displayed.
 If “Don’t show again.” is selected,
the confirmation message will
not be displayed again.
Select “Android Auto” on the home
screen or the apps screen ( P. 8 ,
9) to display the Android Auto
screen.
Displays the application buttons.
Select to start the application.
■About the supported devices
This system compatible with
Android 8.1 or later are supported.
Android Auto
Android Auto can be used to
view Google Maps, play music,
and place calls by connecting
your Android device to the
system, using USB cable and
Bluetooth®. Supported appli-
cations can also be used.
 For details on the services or
the operations, check the
Android Auto site
(https://www.android.com/
auto/) and
(https://support.google.com/
androidauto/).
To use the Android Auto appli-
cation, connect your Android
device to the USB port.
When using the application,
read the precautions indicated
in “Before using applica-
tions”. ( P. 5 6 )
Connecting the Android
Auto device
Overview
Control screen
A

625-3. Android Auto
Automatic display of the Android
Auto screen when an Android
device is connected to the system
via USB, can be enabled/disabled.
1 Display the phone settings
screen. ( P. 2 4 )
2 Select “Android Auto”.
3 Turn “Auto Show Connected
Device” on.
Whether a registered Android
device connects as an Android
Auto device or a USB memory
device can be set.
1 Display the phone settings
screen. ( P. 2 4 )
2 Select “Android Auto”.
3 Select “Device List”.
4 Select “Edit”.
5 Select for the desired
Android device.
1 Display the phone settings
screen. ( P. 2 4 )
2 Select “Android Auto”.
3 Select “Device List”.
4 Select “Edit”.
5 Select next to the desired
device name.
6 Select “Yes”.
7 Select “OK”.
Enabling auto show of
Android Auto screen
Selecting Android devices
to connect to Android Auto
Deleting the Android Auto
device

6
63
6
Audio
Audio
.6-1. Basic operation
Some basics ....................... 64
6-2. Radio operation
AM radio/FM radio .............. 67
DAB .................................... 69
6-3. Media operation
USB memory ...................... 72
iPod/iPhone ........................ 74
Bluetooth® audio................. 76
AUX .................................... 79
Android Auto ....................... 80
6-4. Audio remote controls
Steering switches ............... 82
6-5. Tips for operating the
audio/visual system
Operating information ......... 83

646-1. Basic operation
6-1.Basic operation
“VOLUME” knob: Press and hold
until a message is displayed, and
then select “OK” or wait a few
seconds for the audio/visual sys-
tem to turn off. Press and hold to
turn the system on again. The
system will turn on with the last
audio source used. Turn this
knob to adjust the volume. Press
to mute the audio/visual system.
 button: Press to display
screen buttons for the radio.
●The audio/visual system will remain off if you change the position of
engine switch Off to ACC/ON while
the audio/visual system is off. If you had set the volume to mute, the
audio/visual system will remain mute
and the track will start playing from where it was last stopped.
1 Press the button and select
the “Media”, or press the
button.
2 Select the desired audio source.
Media screen
Radio screen
 Each time button is
pressed, the radio modes can
also be changed.
Some basics
This section describes some of
the basic features of the
audio/visual system. Some
information may not pertain to
your system.
Your audio/visual system
works when the engine switch
is changed to ACC or ON.
NOTICE
●To prevent the 12-volt battery from
being discharged, do not leave the
audio/visual system on longer than necessary when the engine is not
running.
Turning the system on and
off
Selecting an audio source

65
6
6-1. Basic operation
Audio
■Displaying the sound customi-
sation screen
1 Press the button.
2 Select “Settings”.
3 Select “Sound”.
4 Select “Audio”.
5 Select “Sound Customisation”.
■Equaliser settings
How good an audio programme
sounds is largely determined by the
mix of the treble, mid and bass lev-
els. In fact, different kinds of music
and vocal programmes usually
sound better with different mixes of
treble, mid and bass.
1 Display the “Sound Customisa-
tion” screen. ( P. 6 5 )
2 Select “Equaliser”.
3 Set the desired item.
Select the sliders to adjust
low-pitched tones.
Select the sliders to adjust
mid-pitched tones.
Select the sliders to adjust
high-pitched tones.
Select to reset all setup items.
■Balance/Fader settings
A good balance of the left and right
stereo channels and of the front
and rear sound levels is also impor-
tant.
Keep in mind that when listening to
a stereo recording or broadcast,
changing the right/left balance will
increase the volume of 1 group of
sounds while decreasing the vol-
ume of another.
1 Display the “Sound Customisa-
tion” screen. ( P. 6 5 )
2 Select “Balance/Fader”.
3 Adjust to the desired position.
Select the icon to adjust sound
balance.
Select to reset the adjusted
position.
■Vocal Image Control settings
Extract only vo cal sound from
whole sound and adjust volume
balance of it.
1 Display the “Sound Customisa-
tion” screen. ( P. 6 5 )
2 Select “Vocal Image Control”.
Sound settings
A
B
C
D
A
B

666-1. Basic operation
3Adjust to the desired position.
Select the icon to adjust vocal
image control.
Select to set the virtual stage
enhancer function.
This function adjusts the sounds
to the high realistic surround
sound by enhancing the vocals.
When this setting is on, the front
and rear setting of “Vocal Image
Control” cannot be set.
Select to reset the vocal image
control settings.
1 Press this switch to operate the
voice recognition system.
 The voice recognition system
and its list of commands can be
operated. ( P. 9 0 )
Voice recognition system
A
B
C

67
6
6-2. Radio operation
Audio
6-2.Radio operation
The FM/AM radio operation screen
can be accessed by selecting “FM”
or “AM” on the radio control screen.
( P. 6 4 )
Select to change radio modes.
Select to displa y the sound cus-
tomisation screen. ( P.65)
Select to display the radio text.*
Select to display the radio set-
ting screen. ( P. 3 7 )
Select to change the preset sta-
tion list.
Select to step up/down frequen-
cies.
Select and hold to seek frequen-
cies.
Select to change the radio fre-
quency and begin scanning for
receivable radio stations. The
scanning operation will be per-
formed every 10 seconds con-
tinuously.
Select again to stop at a
received radio station.
Select to automatically register
radio stations with high recep-
tion quality to the preset stations
list.
Select to display a list of receiv-
able stations. ( P. 6 8 )
Select to display the PTY select
screen. ( P. 6 8 )*
Select to tune to preset stations.
*: FM Radio only
Turn to adjust the volume.
Press to mute the audio/visual
system.
Press and hold to turn the
audio/visual system off, and
press and hold to turn it on
again.
Turn to step up/down frequen-
cies.
Press and hold to display the
sound customisation screen.
( P. 6 5 )
Press to seek up/down available
AM radio/FM radio
Overview
Control screen
A
B
C
D
E
F
G
Control panel
H
I
J
K
A
B
C

686-2. Radio operation
stations.
●The radio automatically changes to
stereo reception when a stereo broad-
cast is received.
Stations can be registered as pre-
sets.
1 Tune to the desired station.
2 Select and hold one of the
desired preset station buttons.
 To change the preset station to a
different one, follow the same
procedure.
A station list can be displayed.
1 Select “Station List”.
 “Update”: Select to update the
station list.
FM only
2 Select the desired list.
 “All”: Select to display all sta-
tions.
 “Genres”: Select to display cate-
gories.
3 Select the desired station.
The station of a selected PTY (Pro-
gramme Type) can be seeked.
1 Select “PTY Select”.
2 Select the desired PTY.
3 Select “Seek”.
*: This function is not available in some
countries/areas.
This function allows your radio to
receive station and programme
information from radio stations
which broadcast this information.
Depending on the availability of
RDS infrastructure, this function
may not operate properly.
■TA (Traffic Announcement)
function
A pop-up screen is displayed on the
screen and a traffic announcement
is played when, a traffic announce-
ment is received.
●This function can be turned on/off.
( P. 3 7 )
■AF (Alternative Frequency)
function
A station providing good reception
is automatically se lected if current
reception worsens.
●This function can be turned on/off. ( P. 3 7 )
■Emergency announcement
A pop-up screen is displayed on the
screen and an emergency
announcement is played when an
emergency alarm is received.
Registering a station as a
preset
Selecting a station from the
list
PTY select function
Radio data system*