display TOYOTA LAND CRUISER 2007 J200 Navigation Manual

lvii
(c) Search condition
You can designate the route conditions
of the route to the destination.
1. Touch the
“Route” switch.v
2. Touch the “Search Condition”switch. The “Search Condition” screen
appears.
3. Touch the “Quick”, “Quick1”,“Quick2” or “Short” switch and
touch the “OK” switch.
The entire route from the starting point to the
destination is displayed.
“Guide”: To start guidance.
“Route”: To add or change a route. (For de-
tails, see pages liii and lv.)
(d) Detour setting
While the route guidance is operating,
you can change the route to detour
around a section of the route where a
delay is caused by road repairs, an acci-
dent, etc.
1. Touch the
“Route” switch.
2. Touch the “Detour” switch.

lix
3. You can turn the indicator on or off by
touching the switch.
When searching for a route, the system
avoids routes where the indicator is dimmed
as much as possible.
After choosing the conditions, touch the
“OK” switch.
(f) Starting route from adjacent
road
You can start the route guidance from the
adjacent road.
(ex. When the route guidance guides the
route on the freeway, but you drive on the
parallel way along a freeway.)
1. Touch the
“Route” switch.
2. Touch the “Start from Adjacent
Road” switch.
When there is no adjacent road, this switch
will not appear.
Show POI icons
Points of Interest such as gas stations
and restaurants can be displayed on the
map screen. You can also set their loca-
tion as a destination and use them for
route guidance.
1. Touch the “Map View” switch.

lx
2. Touch the “Show POI Icon” switch
to display a particular type of Point of In-
terest on the screen.
A screen with a limited choice of Points of In-
terest will be displayed. (To change the dis-
played POI, see page ci.) When you touch
the desired Point of Interest category, sym-
bols will appear on the map screen indicat-
ing where the POI addresses are located.
To turn off the symbols of the Points of In-
terest on the map screen, touch the
“POI Off” switch.
“More”: If you cannot find your desired
Point of Interest on the limited choice
screen, touch this switch. The screen then
displays the complete POI listing screen.
You can display up to 5 categories of icons
on the screen.
When you select a Point of Interest type from
either the limited list or the complete list, the
screen will display symbols at those loca-
tions on the map screen.
Touching the
“Delete” switch will delete
the last selected icon.
“Local POI List”: If you want to search for
the nearest Point of Interest, touch this
switch. Then choose one of the categories.
The system will list the points within 20 miles
(30 km).

lxi
Touch the switch of your desired Point of In-
terest. Selected Points of Interest are dis-
played on the map screen.
“Dist.”: To sort in the order of distance from
your current location.
“Icon”: To sort in the order of the POI icons.
“Name”: To sort in alphabetical order by
name.
“On Route”: When the indicator is illumi-
nated by touching this switch, the list of the
items searched along the route is displayed.
To set a POI as a destination
You can select one of the Points of Interest
icons on the map screen as a destination
and use it as route guidance.
Directly touch the Point of Interest icon
that you wish to set as a destination.
The map will shift so that the icon is centered
on the screen and overlaps with the cursor
. At this time, the distance from your cur-
rent position can be displayed on the screen.
The distance shown is measured as a
straight line from the current vehicle position
to the POI.
When your desired Point of Interest over-
laps with the cursor, touch the
“Enter
” switch. The screen changes and dis-
plays the map location of the selected
destination and route preference. (See “
— Entering destination” on page xlviii.)
Route overview
1. Touch the “Map View” switch.
2. Touch the “Route Overview”switch.

lxii
The entire route from the current position to
the destination is displayed.
“Guide”: To start guidance.
“Route”: To change the route. (For details,
see pages liii and lv.)
“Turn List”: The following screen displays
the list of the roads up to your destination.You can scroll through the list of roads by
touching
or . However, not all road
names in the route may appear on the list.
If a road changes its name without requiring
a turn (such as on a street that runs through
two or more cities), the name change will not
appear on the list. The street name closest
to the starting point will be displayed with a
mileage to the next turn.
These marks indicate the
direction in which you should turn
at an intersection.
Touch the “Map” switch of your desired
point. The point which you choose is dis-
played on the map screen.

lxiii
Route preview
1. Touch the “Map View” switch.
2. Touch the “Route Preview”switch.
:To indicate the next destination.
:To preview the route to the next des-
tination.
:To preview the route to the next des-
tination in fast−forward mode.
:To stop the preview.
:To review the route to the previous
destination or starting point.
:To review the route to the previous
destination or starting point in fast−
forward mode.
:To indicate the previous destination
or starting point.
Screen configuration
You can choose any one of the screen
configurations.
1. Touch this switch to display the fol-
lowing screen.
2. To select the desired screen configu-
ration, touch one of the following
switches.

lxiv Depending on the conditions, it may not be
possible to select certain screen configura-
tion switches.
:To display single map screen. (See
page lxiv.)
:To display dual map screen. (See
page lxiv.)
:To display compass mode screen.
(See page lxv.)
:To display turn list screen. (See
page lxv.)
:To display arrow screen. (See page
lxvi.)
:To display freeway information
screen. (See page lxvi.)
:To display intersection guidance
screen or guidance screen on free-
way. (See page lxvii.)
(a) Single map
The screen shows the single map.
(b) Dual map
The screen shows the dual map. The map
on the left is the main map.
You can edit the right side map by touching
any specific point on the right side map.

lxv
This screen can perform the following
procedures.
Changing the map scale
Displaying the POI icon
Changing the orientation of the map
Touch the
“OK” switch when you complete
editing. The screen returns to the dual map
screen.
(c) Compass mode
Information about the destination and cur-
rent position, as well as a compass, is dis-
played on the screen.
The destination mark is displayed in the di-
rection of the destination. When driving, re-
fer to the longitude and latitude coordinates
and the compass, to make sure that your ve-
hicle is headed in the direction of the des-
tination.
INFORMATION
When the vehicle goes out of the disc
area, the guidance screen changes into
compass mode.
(d) Turn list screen
The screen shows the turn list. You cannot
scroll through the list of roads.

lxvi
(e) Arrow screen
The screen shows the current road name
and the distance to the next corner.
(f) Freeway information screen
This screen displays the distance to the next
junction and exit, or POIs in the vicinity of the
freeway exit.
“Map”: To display the selected map of the
exit vicinity.
On the left side of the
“Map” switch, up to
five POIs around the selected exit are dis-
played.
:To scroll for farther junctions or exits.
:To scroll for closer junctions or exits.
:To scroll for the closest three junc-
tions or exits.
INFORMATION
When you drive on a freeway, the
screen is automatically divided into
two parts, with freeway information
screen on the right side.

lxvii
(g) Intersection guidance screen/
guidance screen on freeway
Intersection guidance screen
This screen automatically appears when the
vehicle approaches an intersection on the
road.
The distance to the intersection is shown at
the bottom of the screen.
“OFF”: The intersection guidance screen
disappears and the map screen appears.
When touching the
switch or pushing
the
“MAP/VOICE” button, the intersec-
tion guidance screen reappears.
INFORMATION
Intersection guidance can be turned on
or off. (See page xcvii.)
Guidance screen on freeway
This screen automatically appears when the
vehicle approaches a junction or exit on a
freeway.
The distance to the junction or exit is shown
at the bottom of the screen.
“OFF”: The guidance screen on freeway
disappears and the map screen appears.
When touching the
switch or pushing
the
“MAP/VOICE” button, the guidance
screen on freeway reappears.
INFORMATION
Guidance screen on freeway can be
turned on or off. (See page xcviii.)
Distance and time to
destination
When the vehicle is on the guidance
route, the distance and the estimated
travel time to the destination are dis-
played. When the vehicle is not on the
guidance route, the distance to and the
direction of the destination are dis-
played.
When driving on the guidance route and
more than one destination is set, the dis-
tance and the estimated travel time from cur-
rent position to each destination are dis-
played.
1. Touch this switch to display the fol-
lowing screen.