ignition ASTON MARTIN V8 VANTAGE 2010 Owner's Manual
[x] Cancel search | Manufacturer: ASTON MARTIN, Model Year: 2010, Model line: V8 VANTAGE, Model: ASTON MARTIN V8 VANTAGE 2010Pages: 947, PDF Size: 43.21 MB
Page 508 of 947
Anti-lock Braking System (ABS) (06.09)
Brake system (06.00)
6-9-2 Workshop Manual Issue 4, November 2008
difference between the ideal and actual response within a
tolerance band. This directly influences the forces on the
tires to generate a corrective yaw moment to reduce the side
forces of the tires where appropriate
System Overview
The DSC system embraces capabilities far beyond that of
ABS, or ABS and traction control combined, while relying on
the components of these systems. It also incorporates these
additional sensors for measur ing the vehicle’s motion and
brake system pressure:
Ya w r a t e s e n s o r - located centrally on the transmission
tunnel.
Lateral acceleration sensor - integrated with the yaw rate
sensor.
Steering angle sensor - located on the upper steering
column.
Pressure transducer - located on master cylinder.
The ABS / DSC module supports data exchange with other
vehicle electronic systems via the CAN network; the module
also enables diagnostic interrogation using WDS.
The following components register driver demand and the
ABS / DSC module processes their signals as a basis for
defining an ideal response:
PCM - position of accelerator pedal.
Brake master cylinder pressure transducer - driver’s
braking effort.
Steering angle sensor - position of steering wheel.
There are many supplementary parameters also included in
the processing calculations these include the coefficient of
friction and vehicle speed. The ABS / DSC module monitors
these factors based on signals transmitted by the sensors for:
• Wheel speed
• Lateral acceleration
• Brake pressure
• Yaw rate
Using these parameters, the function of the ABS / DSC
module is to determine the current vehicle status based on
the yaw-rate signal and the slip as estimated by the ABS /
DSC module. It then maintains the vehicle response within
a tolerance of the ‘normal’ behaviour, which is easily
controlled by the driver.
In order to generate the desired yaw behaviour the ABS /
DSC module controls the selected wheels using the ABS
hydraulic system and engine control system. In the event of
engine intervention, the ABS / DSC module calculates the
torque which should be supplied by the engine to the
wheels, and relays this request signal to the PCM which
implements the torque request.
The PCM receives signals from the DSC system via the CAN
bus and reduces engine torque as follows:
• The throttle is positioned to provide the requested engine target torque. • During the transient phase of torque reduction caused by
mechanical and combustion delays, other alternative
torque reduction methods are used to provide a quicker
response.
• The ignition is retarded and / or the fuel is cut-off at the injectors at selected cylinders.
• Ignition and fuelling are reinstated when the engine torque reaches the requested value
Operation Summary
• DSC is switched ‘ON’ when the engine is started
• When the system is operating , the DSC light in the instrument cluster will flash, at the rate of twice a second
• DSC can be switched ‘OFF / ON’ by pressing the DSC switch
• The DSC light in the instru ment cluster will illuminate
continuously when the system is switched ‘Off’.
• ‘DSC OFF’ will be displayed in the message centre right to indicate the system has been switched ‘OFF’
• A malfunction in the traction control system will be indicated to the driver by the following:
• The DSC light in the instru ment cluster will illuminate
continuously
• The message ‘DSC NOT AVAILABLE’ will be displayed in the message centre right
• If vehicle speed control is engaged it will automatically disengage when traction control is operating .
Traction Control
Traction control is a function of DSC, and is operated in
association with DSC. Traction control prevents excessive
wheel-spin at standing starts, or during acceleration. Wheel-
spin is usually caused by ex cessive use of the accelerator
pedal, or slippery, loose or bumpy road surfaces. To prevent
excessive wheel-spin and mainta in vehicle stability such
situations are overcome by the intervention of the traction
control system by:
• Braking the driven-wheel when it starts to slip
• And / or adapting the engine torque to a level corresponding to the traction available on the road
surface.
Functional Description
Traction control uses the ABS electronic and mechanical /
hydraulic hardware with additional valves to control the
braking pressure at the calipe rs. An engine interface also
enables the engine to respond to torque reduction requests
from the traction control. As with ABS, the signals from the
wheel-speed sensors are supplied to the ABS module, where
they are used to calculate the wheel-slip of the individual
wheels. Traction control intervention is initiated if the slip at
one of the wheels is excessive.
Page 509 of 947
Anti-lock Braking System (ABS) (06.09)
Brake system (06.00)
Issue 4, November 2008 Workshop Manual 6-9-3
Engine Intervention
In the event of wheel-slip the ABS / DSC module calculates
the torque, which should be applied by the engine to reduce
the wheel-slip (this torque does not exceed driver demand).
Engine torque reduction is then requested from the PCM via
the CAN bus. The PCM, in response to these signals, reduces
engine torque by controlling the ignition and fuelling. A
traction control gearshift pattern is automatically selected
within the automatic transmission software whenever
traction control is active.
Brake Intervention
This function operates by increasing the pressure in the
brake caliper of the slipping wheel, by closing the separation
valve and the inlet valve of the non-slipping wheel and
running the modulator pump. This takes fluid from the fluid
reservoir via the non-actuated master cylinder and
pressurizes the brake caliper. The pressure is modulated at
the caliper via the inlet and outlet valves to achieve the
desired wheel-slip target to maximize traction.
ABS / DSC Circuit
Specifications
SR,05UR,05YR,0.5NR,0.5
WR,05NR,05
YG,05WG,05
YU,05WU,05
W,05N,05
W,0.5U,0.5R,0.5
P,0.5Y,0.5
B,0.5WG,0.5GB,0.5
B,0.5BG,0.5
GW,0.5
P,0.5
U,0.5
U,3.0
BK,1.0BK,1.0
P,0.35P,0.35P,0.35 U,3.0
WG,05YG,05
WU,05
SR,05UR,05YR,0.5NR,0.5
WG,05YG,05
WU,05
WG,05YG,05
WU,05YU,05YU,05YU,05Module-ABS
OBD2-Body (B)
Earth-Module ABSEarth-Module ABS
C1184-18C2410-6
Sensor-Brake Pressure
Sensor-Brake Pedal Travel
Sensor-Rear ABS-LH
C0746-7C0746-6
C0746-5
Switch-Brake Boost
Sensor-Yawrate / Acceleration
C2411-6C2411-5C2411-4
C2411-3
C0144-7C0144-3
C0144-2
Sensor-Front ABS-LH
Sensor-Front ABS-RH
C2410-10C2410-9
C2410-8
Sensor-Rear ABS-RH
C0746-4C0144-1C2410-7
C0877-7
K-LINESPL50-KL/FA
C0362-1C0434-1
C2444-2
SIGC2444-1
GND
C2444-3
SENSP
C2446-2
GNDC2446-1
SENSPT
C2446-3
SIG
C0501-47
GNDC0501-16
GND
C0501-2K-LINE
C0501-24
GND
C0501-31
PWM
C0501-30
NC
C0501-25
CAN HS-
C0501-28
SIGC0501-27
NO
C0501-29
CAN HS+C0501-6
CLUST_SP
C0501-17
PWR
C0501-5
GND
C0501-32BATT FEED
C0501-7
SENSPT
C0501-3 SIG
C0501-20 SIGC0501-19
GND
C0501-18 SENSP
C0501-4IGN FEED
C0501-46
F/L/GNDC0501-45
F/L/SIG
C0501-42
R/R/GNDC0501-43
R/R/SIG
C0501-36
R/L/SIG
C0501-34
F/R/SIGC0501-33
F/R/GND
C0501-1
BATT FEEDC0501-37
R/L/GND
C2448-5
C2448-3
C2448-2C2448-1
C2448-4
C1656-3 CLUS_SPC1656-2
CAN HS+C1656-1 CAN HS-
C1656-5
GND
C0516-2-C0516-1+
C0517-2
-C0517-1+
C0502-1
+
C0503-2 -C0503-1+
C0502-2 -
Sensor
Steering Angle
Sheet 61
F4
30.0 AmpsRelay 1
Underbonnet Fusebox
DIODE 1
F28
10.0 Amps
F20
30.0 Amps
F19
30.0 Amps
Earth
Steering Angle
Sensor
C0576-1
C0577-4C2608-1 VBATT
C0573-2
C0571-3
C0573-3
C0578-8SPL5-VIGN/FOR
C1672-5
VPWRC1672-8
GND
011-6-003
Oils/Greases
Brake FluidCastrol Response Super Dot 4
Torque Figures
DescriptionNm.lb. / ft.
Modulator to Bracket 5 4
Modulator / Bracket to body 9 7
Brake hose unions 17 1413
10.5
17 Nm. 17 Nm.
17 Nm.
14 Nm.
14 Nm. 14 Nm.
Page 530 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-14 Workshop Manual Issue 5, January 2010
6. Remove bolt, separate bracket clamp and remove reservoir (see Figure 3).
Install
1. Install reservoir and clamp to bracket.
2. Install reservoir hoses to valve unit and pump then install new clips (remove drain tray) (see Figure 1).
3. Install reservoir hoses to clips.
4. Top-up reservoir.
5. Connect vehicle battery.
6. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
7. Top-up reservoir.
8. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
9. Lower vehicle on ramp.
Pump Inlet/Valve Body Bleed/Reservoir
Ta n k H o s e s
-Renew-Roadster Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
4. Remove clips and release reservoir hoses from valve unit and pump (place drain tray to collect fluid) (see Figure
1).
Figure 3
Figure 1
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.
!
!
Repair Operation Time (ROT)
ItemCode
Pump Inlet/Valve Body Bleed/Reservoir
Tank Hoses-Renew 07.03.AF
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
Figure 1
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YO U HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
!
Page 531 of 947
Manual Transmission (07.03)
Transmission (07.00)
Issue 5, January 2010 Workshop Manual 7-3-15
5. Release reservoir hoses from transaxle mounting clips (x2) (see Figure 2).
6. Remove clips and release hoses from reservoir (see Figure 3).
Install
1. Install hoses to reservoir and fit new clips.
2. Install reservoir hoses to valve unit and pump. Fit new clips (remove drain tray).
3. Install reservoir hoses to clips.
4. Top-up reservoir.
5. Connect vehicle battery.
6. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
7. Top-up reservoir.
8. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
9. Lower vehicle on ramp.
Hydraulic Pump Assembly-Renew-
Sportshift Only
Removal
1. Raise vehicle on ramp.
2. Disconnect vehicle battery.
3. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
4. Disconnect pump multiplug (see Figure 1).
5. Remove ground eye from pump body (bolt x1) (see Figure 2).
6. Clamp reservoir hose.
Figure 2
Figure 3
WA R N I N G
ALWAYS CONNECT THE BATTERY EARTH (+VE)
TERMINAL FIRST.
!
!
Repair Operation Time (ROT)
!
!
Page 532 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-16 Workshop Manual Issue 5, January 2010
7. Remove clip and release from pump (place drain tray to collect fluid) (s ee Figure 3).
8. Remove HP hose from pump.
9. Remove and discard O-ring from hose.
10. Remove pump from transaxle (bolts x2).
Install
1. Install pump to transaxle.
2. Install new O-ring to HP hose. Install hose to pump.
3. Install reservoir hose to pump then install new clip (remove drain tray).
4. Connect pump multiplug.
5. Install ground eye to pump body.
6. Top-up reservoir.
7. Connect vehicle battery.
8. Lower vehicle, turn igniti on ON for 20 seconds to
activate gearbox pump. Turn ignition OFF and raise
vehicle.
9. Top-up reservoir.
10. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
11. Lower vehicle on ramp.
HP Hose Kit-Renew-Roadster Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp and secure with straps.
3. Remove road wheel(s).
4. Remove rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
5. Remove centre undertray (see Workshop Manual procedure 01.02.MB Undertray - Centre - Renew).
6. Remove bolts (x4) and subframe cross brace.
7. Remove centre exhaust mounting bolts (x4) (see Figure 1).
8. Loosen clamp nuts (x2), release centre pipe from both catalysts.
9. Remove centre pipe and rear exhaust pipes as an
assembly.
10. Remove bolts/washers (x4), tunnel heatshield to body, remove heatshield.
11. Remove bolts (x8), shear plate to body, remove shear plate.
12. Remove bolt securing earth lead to transaxle.
13. Mark drive shaft to differential flanges for assembly purposes.
14. Remove and discard Allen bolts (x12), collect plates (x6), drive shaft flanges to transaxle.
WAR NI NG
TRANSAXLE OIL CAN BE HARMFUL.
OBEY ALL TRANSAXLE OIL MANUFACTURER’S SAFETY INSTRUCTIONS WHEN YOU HANDLE COMPONENTS
THAT HAVE TOUCHED TRANSAXLE OIL.
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.
Repair Operation Time (ROT)
ItemCode
HP Hose Kit-Renew-Roadster Only 07.03.AH
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE
REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
Figure 1
!
Page 590 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-9
11. Remove nut fuel filter clamp to bracket (see Fig. 2).
1. Remove the fuel filter clamp and withdraw the filter.
Installation
1. Position filter in cl amp and install nut (x1).
2. Connect fuel filter hoses (x2).
3. Install fuel tank service cover (nuts x7).
4. Install fuel tank cover with new seal.
5. Install luggage compartment front floor carpet and retainers (x6)
6. install luggage compartment rear floor carpet.
7. Connect battery earth lead.
Fuel Pump and Reservoir Assembly-
Renew
Removal
1. Depressurise fuel system (see Workshop Manual procedure 10.01.EK Fuel System - Depressurise).
2. Disconnect battery earth lead.
3. Release and remove luggage compartment rear floor carpet.
4. Remove luggage compartment front floor carpet retainers (x6).
5. Remove luggage compartment front floor carpet.
6. Remove fuel tank cover, clean off the sealant around the aperture.
7. Remove nuts (x7) and release fuel tank service cover and clamp.
8. Install the fuel tank drainage adaptor (see Fig. 1).
9. Connect the external pipe to a fuel recovery unit.
Recover the fuel in accordance with the recovery unit
instructions.
Fig. 3
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination. Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
$ $
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Ensure there is adequate ventilation inside the vehicle
(i.e. place the vehicle in a well ventilated area, with the
windows open).
Warning
Disconnect the battery eart h lead before commencing
work on the fuel system.
Caution
The following procedure is completed inside the vehicle
cabin area. Extra care must be taken to ensure no fuel or
fuel vapours come into contac t with the vehicle interior.
Fig. 1
Warning
Several litres of fuel remain in the fuel tank sump after draining.
$
Page 591 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-10 Workshop Manual May 2007
10. Remove recovery unit and fuel tank drainage adaptor.
11. Release the fuel filter hose to pump (x1) quick release
unions (see Fig. 2).
12. Release vent hose from fuel pump assembly (see Fig. 3).
13. Release fuel hose and tank harness from fuel pump bracket clip.
14. Disconnect wiring harness plugs (x2). 15. Install fuel pump removal tool (310-140) (see Fig. 4).
16. Turn the fuel pump anti-clockwise, release and
withdraw pump from mounting.
17. Remove fuel pump.
Installation
1. Position fuel pump in its mounting . Using the service tool, turn clockwise to secure fuel pump.
2. Secure fuel hose and tank harness to bracket
3. Install vent hose to fuel pump.
4. Connect hose to pump assembly.
5. Connect wiring harness multiplugs (x2).
6. Connect fuel filter pipes.
7. Install fuel tank service cover and clamp.
8. Install fuel tank cover with new seal.
9. Install luggage compartment front floor carpet and retainers (x6).
10. Install luggage compartment rear floor carpet.
11. Connect battery earth lead.
Fig. 2
Fig. 3
$ %
$
Fig. 4
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
$
Page 594 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-13
22. Remove cable tie carbon canister to bracket (see Fig. 11).
23. Remove carbon canister from fuel tank (clips 4) (see Fig. 12)
24. Remove tank from support plate.
Installation
1. Position tank to support plate.
2. Install new cable tie behind carbon canister bracket.
3. Align and secure carbon canister to clips (x4).
4. Tighten cable tie around carbon canister.
5. Connect multiplug (x1) fuel tank harness.
6. Install nut (x1) fuel tank harness earth.
7. Secure fuel tank harness (clips x5).
8. Connect fuel vapour hose quick fit connection to tank.
9. With assistance position tank and secure with bolts (x14)
10. Install vacuum hose clip to tank bolts / studs (x4)
11. install vacuum hose clips to studs and secure vacuum
hose.
12. Install nuts (x5) oil cooler to body.
13. Install heatshield. 14. Connect vapour purge and fuel pipe to tank.
15. Position earth lead and secure with nut.
16. Connect fuel tank harness to main harness.
17. Connect evaporative emis
sion control assembly hose
and secure with jubilee clip.
18. install filler neck pipe and hose assembly to fuel tank.
19. Position filler neck pipe, hose assembly and sealing washer to body.
20. Install nut filler neck pipe and hose assembly to body.
21. Install bolt filler pipe brac ket to spring damper assembly.
22. install fuel filler cap
23. Install rear subframe (see Workshop Manual procedure
02.01.CA Subframe Assembly - Rear - Remove for
Access and Refit).
24. Connect vehicle battery.
Fuel Tank and Canister Assembly-
Remove for Access/Refit
Removal
1. Disconnect vehicle battery.
2. Remove rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear -
Remove for Access and Refit).
Fig. 11
Fig. 12
Warning
The fuel tank is heavy. Fuel tank removal / replacement
is a two person operation.
$ $
$ %
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the
vehicle battery.
Page 596 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-15
17. With assistance support tank, remove bolts (x14) tank to body and remove fuel tank (see Fig. 6).
Installation
1. With assistance position tank and secure with bolts (x14)
2. Install vacuum hose clip to tank bolts / studs (x4)
3. install vacuum hose clips to studs and secure vacuum hose.
4. Install nuts (x5) oil cooler to body.
5. Install heatshield.
6. Connect vapour purge and fuel pipe to tank.
7. Position earth lead and secure with nut.
8. Connect fuel tank harness to main harness.
9. Connect evaporative emission control assembly hose and secure with jubilee clip.
10. install filler neck pipe and hose assembly to fuel tank.
11. Position filler neck pipe, hose assembly and sealing washer to body.
12. Install nut filler neck pipe and hose assembly to body.
13. Install bolt filler pipe bracket to spring damper assembly.
14. install fuel filler cap
15. Install rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear - Remove for
Access and Refit). 16. Connect vehicle battery.
Fuel Tank Sender Assembly-Renew
Removal
1. Disconnect battery earth lead.
2. Release and remove luggage compartment rear floor
carpet.
3. Remove luggage compartment front floor carpet retainers (x6) and remove carpet.
4. Remove fuel tank cover, clean off the sealant around the aperture.
5. Remove nuts (x7) and release plate clamp and fuel tank service cover.
Fig. 6
Warning
The fuel tank is heavy. Fuel tank removal / replacement
is a two person operation.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination. Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
$
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.
Warning
Ensure there is adequate ventilation inside the vehicle
(i.e. place the vehicle in a well ventilated area, with the windows open).
Caution
The following procedure is completed inside the vehicle
cabin area. Extra care must be taken to ensure no fuel or
fuel vapours come into contac t with the vehicle interior.
Page 597 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-16 Workshop Manual May 2007
6. Install the fuel tank drainage adaptor (see Fig. 1).
7. Connect the external pipe to a fuel recovery unit.
Recover the fuel in accordance with the recovery unit
instructions.
8. Remove the recovery unit and fuel tank drainage adaptor.
9. Disconnect fuel tank sender unit multiplug (see Fig. 2).
10. Release fuel tank sender assembly from bracket. 11. Remove fuel tank sender unit (see Fig. 3).
Installation
1. Install sender unit, secure to bracket and connect
multiplug .
2. Install nuts (x7) securing plate clamp and fuel tank
service cover.
3. Install fuel tank cover with new seal.
4. Install luggage compartment front floor carpet and retainers (x6).
5. Install luggage compartment rear floor carpet
.
6. Connect battery earth lead.
Fuel Vapour Pipe Assembly-Renew
Removal
1. Battery isolation switch off.
Fig. 1
Fig. 2
$
$
Fig. 3
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
ItemCode
Fuel Vapour Pipe Assembly-Renew 10.01.KA
Warning
Read and follow all fuel handling instructions (at the beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and disp ose of fuel contaminated
materials safely.
$