dry oil ASTON MARTIN V8 VANTAGE 2010 Owner's Guide
[x] Cancel search | Manufacturer: ASTON MARTIN, Model Year: 2010, Model line: V8 VANTAGE, Model: ASTON MARTIN V8 VANTAGE 2010Pages: 947, PDF Size: 43.21 MB
Page 410 of 947
Power Conversion (03.11)
Engine (03.00)3-11-38 Workshop Manual May 2007
3. Position new oil seal (fitted dry). Install oil seal in timing
cover using tool (303-750) (see Figure 3).
Figure 3
4. Remove crankshaft oil seal protector.
5. Install crankshaft pulle y (see Workshop Manual
procedure 03.11.DP Pulley Assembly - Crankshaft
Damper - Renew With Engine Removed).
Crankshaft Rear Oil Seal-Renew (with
Engine Removed
)
Removal
1. Remove engine assembly (see Workshop Manual
procedure 03.00.AA Engi ne Assembly - Renew).
2. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
3. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
4. Remove bolts (x6), clutch cover to flywheel.
5. Release clutch cover from dowels (x3), remove clutch cover, collect drive plate.
6. Remove and discard bolts (x8), flywheel to crankshaft flange.
7. Remove bolts (x2), collect tool (303-1185).
8. Release flywheel from dowel, remove flywheel.
9. Position tool (303-1189) to crankshaft flange, screw in
alignment bolts (x2) 1.5 turns (only).
10. Use tool and pierce holes (x3) in oil seal through holes in special tool for self-tapping screws
11. Install and tighten self-tapping screws (x3) into oil seal.
12. Tighten centre bolt of tool (303-1189) and withdraw crankshaft oil seal.
13. Remove oil seal from special tool, discard oil seal.
Installation
1. Clean oil seal aperture in cylinder block.
2. Ensure that oil seal protector is positioned correctly and install oil seal onto crankshaft flange.
3. Install tool (303-1189) to crankshaft, position nuts on
tool against oil seal.
4. Ensure that oil seal and special are parallel to rear of engine.
5. To install oil seal, tighten nuts alternately on tool (303- 1189) until oil seal correctly seated.
6. Remove special tool from crankshaft.
7. Check that the oil seal is located correctly.
8. Clean flywheel and mating face on crankshaft.
9. Install flywheel, align to dowel on crankshaft flange.
10. Install new bolts (x8), install tool (303-1185) to restrain flywheel. Torque tighten bolts (x8) in the correct
sequence.
11. Clean clutch cover and drive plate.
12. Install clutch assembly on flywheel, align to dowels (x3).
13. Install bolts (x6), install clutch alignment tool, evenly torque tighten bolts (x6) in a diagonal sequence.
Remove clutch alignment tool.
14. Remove bolts (x2), collect tool (303-1185).
15. Install inspection cover, install and torque tighten bolts (x2).
16. Install engine assembly (see Workshop Manual procedure 03.00.AA Engine Assembly - Renew).
Repair Operation Time (ROT)
A0311247
Caution
Do not use any lubricant on cr ankshaft oil seals or seal
protectors. Make sure all co mponents are clean and dry
Caution
Alternate nut tightening to correctly seat the crankshaft rear oil seal.
Page 513 of 947
May 2007 Workshop Manual 7-2-1
Transmission (07.00)
Contents
Transmission Cooling (07.02) ............................... 7-2-2Specifications.......................................................... 2-2
Maintenance ........................................................... 2-2Oil Cooler Matrix-Renew ....................................... 2-2
Manual Transmission Oil Ou tlet Hose-Renew ........ 2-3
Manual Transmission Oil Inlet Hose-Renew ........... 2-3
Manual Transmission (07.03) ................................ 7-3-1 Description ............................................................. 3-1Cooling .................................................................. 3-1
Specifications.......................................................... 3-2
Maintenance ........................................................... 3-2 Transaxle Assembly-Remove for Access/Refit .......... 3-2
Complete Sportshift Hydraulic Kit-Renew .............. 3-6
Complete Shifter Assembly-Renew-Roadster Only.. 3-9
Reservoir Tank Assembly-Renew-Roadster Only ... 3-10
Pump Inlet/Valve Body Bleed/Reservoir
Tank Hoses-Renew-Roadster Only ....................... 3-11
Hydraulic Pump Assembly-Renew
-Sportshift Only.................................................... 3-12
HP Hose Kit-Renew-Roadster Only ...................... 3-13
Dry Break Connector-Renew-Roadster Only ........ 3-15
Clutch Position Sensor-Renew
-Roadster/Sportshift Only ..................................... 3-17
Transmission Sensor Assembly
-Renew-Sportshift Only ........................................ 3-18
Transmission Valve Block-Renew ......................... 3-20
Shifter Assembly Gasket-Renew ........................... 3-23
Transaxle Assembly-Remove for Access & Refit
-Sportshift Only.................................................... 3-23
Transmission Axle Assembly-D rain/Refill............... 3-26
Transaxle Assembly-Renew .................................. 3-26
Automatic Control System (07.05) ........................ 7-5-1 Maintenance ........................................................... 5-1Paddle Shift Switch Assembly - Renew
- (Sportshift Only)................................................... 5-1
Sportshift Drive Switch-Ren ew-Sportshift Only ....... 5-1
Sportshift Neutral Switch-Renew-Sportshift Only .... 5-2
Sportshift Reverse Switch-Renew-Sportshift Only ... 5-2
Sportshift Comfort Switch-Renew-Sportshift Only ... 5-3
Sportshift Interface Box-Re new-Sportshift Only ...... 5-3
Manual Control System (07.06) ............................. 7-6-1 Maintenance ........................................................... 6-1Gearshift Assembly Mechan ism-Renew .................. 6-1
Transmission Gearshift Cable Assembly-Renew ...... 6-1
Automatic Shifting Subsystem (07.11)................. 7-11-1 Maintenance ......................................................... 11-1Transmission Control Module
-Renew-Sportshift Only ........................................ 11-1
Page 527 of 947
Manual Transmission (07.03)
Transmission (07.00)
Issue 5, January 2010 Workshop Manual 7-3-11
36. Mark and disconnect valve-block connectors positions. Disconnect multiplugs (x5) (see Figure 10).
37. Remove bolt valve block to transaxle (see Figure 11).
38. Remove nuts (x3) securing valve block to transaxle and remove Sportshift hydrau lic kit (see Figure 12).
Install
1. Install Sportshift hydraulic ki t valve block to stud and fit
nuts.
2. Install bolt valve block to transaxle. 3. Connect multiplugs (x5) to valve block.
4. Connect dry break quick-fit connector to torque tube
pipe.
5. Install pump to transaxle.
6. Install ground eye to pump body.
7. Connect pump multiplug.
8. Clean mating faces and install new shifter unit gasket to dowels.
9. Ensure alignment of selector mechanism with shifter unit
and install shifter unit.
10. Install harness clip into shifter casing.
11. Secure hoses to support clip.
12. Connect gear position sensor to multiplug.
13. Install gear position sensor (screws x4).
14. Raise transaxle, install harness clip to subframe.
15. Connect transaxle breather pipe.
16. Raise transaxle to fitted position. Install transaxle mounting brackets and hydramounts, install and torque
tighten new bolts (x8).
17. Align hydramounts to subframe, lower lifter, install and torque nuts. Remove lifter.
18. Position reservoir to bracket and fit clamp (bolt x1).
19. Position reservoir hose and secure clips.
20. Remove plugs, connect and torque oil cooler unions.
21. Apply thread lock to new Allen bolts.
22. Align drive shafts to transaxle flanges, clean and install plates (x6), install and torque tighten Allen bolts (x12).
23. Position earth lead to transaxle, install and torque tighten bolt.
24. Install shear plate, install bolts (x8), tighten bolts to correct torque.
25. Install tunnel heatshield, install bolts/washers (x4),
tighten bolts to correct torque.
26. Install centre and rear exha ust pipe assembly, align to
both catalysts. tighten clamp nuts to correct torque.
27. Install bolts (x4) into centre mounting.
28. Install subframe cross brace, install bolts (x4) and torque.
29. Install rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Re move for Access & Refit).
30. Roadster Only - Install centre undertray (see Workshop
Manual procedure 01.02.MB Undertray - Centre -
Renew).
31. Install road wheel(s).
32. Lower vehicle on ramp, remove securing straps.
Figure 10
Figure 11
Figure 12
!
!
!
WA R N I N G
OBSERVE ALL TRANSAXLE OIL MANUFACTURERS
SAFETY INSTRUCTIONS WHEN HANDLING
COMPONENTS THAT HAVE BEEN IN CONTACT WITH
TRANSAXLE OIL.
New Allen bolts should have a thread lock coating.
Page 535 of 947
Manual Transmission (07.03)
Transmission (07.00)
Issue 5, January 2010 Workshop Manual 7-3-19
Dry Break Connector-Renew-Roadster
Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp and secure with straps.
3. Remove road wheel(s).
4. Remove rear exhaust silencer assembly (see Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
5. Remove centre undertra y (see Workshop Manual
procedure 01.02.MB Undertray - Centre - Renew).
6. Remove bolts (x4), subframe cross brace.
7. Remove centre exhaust mounti ng bolts (x4) (see Figure
1).
8. Loosen clamp nuts (x2), rele ase centre pipe from both
catalysts.
9. Remove centre pipe and rear exhaust pipes as an assembly.
10. Remove bolts/washers (x4), tunnel heatshield to body, remove heatshield.
11. Remove bolts (x8), shear plate to body, remove shear plate.
12. Remove bolt securing earth lead to transaxle.
13. Mark drive shaft to differential flanges for assembly purposes. 14. Remove and discard Allen bolts (x12), collect plates (x6),
drive shaft flanges to transaxle.
15. Position drain container to collect oil spillage.
16. Loosen unions and disconnect oil cooler pipes (x2) from
transaxle interconnecting pipes and plug pipe
connections (x4).
17. Remove drain container.
18. Disconnect transaxle breather pipe.
19. Release reservoir hose from mounting bracket (Clips x2)
(see Figure 2).
20. Remove bolt from reservoir bracket, release and remove clamp, tie reservoir aside (see Figure 3).
21. Remove nuts (x2), hydramounts to subframe mountings.
22. Position hydraulic lifter to support transaxle.
Repair Operation Time (ROT)
!
WA R N I N G
OBSERVE ALL OIL/FLUID MANUFACTURERS SAFETY INSTRUCTIONS WHEN HANDLING COMPONENTS
THAT HAVE BEEN IN CONTACT WITH TRANSAXLE OIL.
Caution
Plug oil cooler connections to prevent ingress of dirt or moisture into the system.
Figure 2
Figure 3
!
!
Page 536 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-20 Workshop Manual Issue 5, January 2010
23. Remove and discard bolts (x8, 4 each side), mounting brackets to transaxle. Remove mounting brackets with
hydramounts.
24. Release drive shafts from transaxle and position aside.
25. Lower transaxle sufficiently to access harness to subframe clip, release harness to subframe clip (see
Figure 4).
26. Lower transaxle to approx . 420mm from fitted position
and retain on hydraulic lifter (see Figure 5). 27. Disconnect dry break quick-
fit connector from torque
tube pipe (see Figure 6).
28. Remove retaining clip from valve unit and disconnect hose.
29. Remove hose from under valve unit (see Figure 7).
Install
1. Install hose under valve unit.
2. Connect hose to valve unit and install retaining clip.
3. Connect dry break quick-fit connector to torque tube pipe.
4. Raise transaxle, install harness clip to subframe.
5. Connect transaxle breather pipe.
6. Raise transaxle to fitted position.
7. Install transaxle mounting brackets and hydramounts, install and torque tighten new bolts (x8).
8. Align hydramounts to subfra me, lower lifter, install and
torque nuts and remove lifter.
9. Position reservoir to bracket and fit clamp (bolt x1).
10. Position reservoir hose and secure clips.
11. Remove plugs, connect and torque oil cooler unions.
12. Apply thread lock to new Allen bolts.
13. Align drive shafts to transaxle flanges, clean and install plates (x6), install and torque tighten Allen bolts (x12).
Figure 4
WAR NI NG
THE TRANSAXLE ASSEMBLY IS VERY HEAVY. GET THE
AID OF ONE MORE PERSON WHEN YOU MOVE THE
TRANSAXLE. IF YOU DO NOT, PERSONAL INJURY CAN OCCUR.
Figure 5
!
!
Figure 6
Figure 7
!
!
Page 542 of 947
Manual Transmission (07.03)
Transmission (07.00)7-3-26 Workshop Manual Issue 5, January 2010
33. Remove bolt valve block to transaxle (see Figure 8).
34. Remove nuts (x3) securing valve block to transaxle and remove valve block from studs (see Figure 12).
Install
1. Install valve block to stud and fit nuts.
2. Install bolt valve block to transaxle.
3. Install hoses (x3) to valve block and install new clips.
4. Install pipe into valve bl ock and bolts (x2) pump to
transaxle (renew O-ring on hose).
5. Install clip pump hose to valve block.
6. Install reservoir hose to valve block and install new clip.
7. Connect multiplugs (x5) to valve block.
8. Connect dry break quick-fit connector to torque tube pipe.
9. Raise transaxle, install harness clip to subframe.
10. Connect transaxle breather pipe.
11. Raise transaxle to fitted position.
12. Install transaxle mounting brackets and hydramounts, install and torque tighten new bolts (x8).
13. Align hydramounts to subfra me, lower lifter, install and
torque nuts. Remove lifter.
14. Position reservoir to bracket and fit clamp (bolt x1).
15. Position reservoir hose and secure clips.
16. Remove plugs, connect and torque oil cooler unions.
17. Apply thread lock to new Allen bolts.
18. Align drive shafts to transaxle flanges, clean and install plates (x6), install and torque tighten Allen bolts (x12).
19. Position earth lead to transaxle, install and torque tighten bolt.
20. Install shear plate, install bolts (x8), tighten bolts to correct torque.
21. Install tunnel heatshield, install bolts/washers (x4), tighten bolts to correct torque.
22. Install centre and rear exhaust pipe assembly, align to both catalysts then tighten clamp nuts to correct torque.
23. Install bolts (x4) into centre mounting.
24. Install subframe cross brace, install bolts (x4) and torque. 25. Install rear exhaust silencer assembly (see Workshop
Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
26. Roadster Only - Install centre undertray (see Workshop
Manual procedure 01.02.MB Undertray - Centre -
Renew).
27. Install road wheel(s).
28. Lower vehicle on ramp, remove securing straps.
29. Connect vehicle battery.
30. Test drive vehicle.
Shifter Assembly Gasket-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp and secure with straps.
3. Remove gear position sens or (see Workshop Manual
procedure 07.03.AL Sensor - Transmission Assembly -
Sportshift - Renew).
4. Remove shifter unit fixings (bolts x6, nut x1), release from dowels (x2) and tie shifter aside (see Figure 1).
Figure 8
!
WAR NI NG
ALWAYS CONNECT THE BATTERY EARTH (+VE) TERMINAL FIRST.
Repair Operation Time (ROT)
ItemCode
Shifter Assembly Gasket-Renew 07.03.AN
WAR NI NG
ALWAYS DISCONNECT THE BATTERY EARTH (- VE) TERMINAL FIRST.
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
Figure 1
!
Page 584 of 947
Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-3
Fuel Tank
The fuel tank incorporates a single filler neck and check valve, internal fuel pump, internal fuel filter, a sender unit and an
‘on board refuelling vapour recovery’ system.
Fuel Pumps
) X H O 3 X P S
The modular fuel pump is immersed in the base of the fuel
tank. The pump can deliver up to 150 litres/hour. The in-
tank fuel line connects to the external line using a quick-fit
connector in the base of the fuel tank. During normal running, pressu
rised fuel from each fuel
pump passes from the tank, through an 3 micron in-tank fuel
filter to one of the two fuel rails on the engine.
Fuel temperature is measured on the primary fuel rail. If fuel
temperature becomes excessive, the fuel pressure is
increased to prevent fuel vaporisation (boiling).
Fuel pressure is measured by sensors on each fuel rail. The
fuel pressure to each rail is regulated as required by
continuously changing the run speed of the associated fuel
pump. Maximum pressure in the system is limited to 5.3 bar
by in-tank pressure regulators.
A constant head of fuel is maintained in the fuel pump
modules to ensure that the pumps cannot run dry in a ‘low
fuel’ situation.
) X H O 3 X P S
) X H O / L P L W 9 H Q W 9 D O Y H 5 R O O 2 Y H U 9 D O Y H
+ L J K 3 U H V V X U H ) H H G I U R P 5 + 6 3 X P S ) L O O H U 1 H F N
& K H F N 9 D O Y H - H W 3 X P S / R Z 3 U H V V X U H
) H H G W R W K H 6 Z L U O 3 R W
Page 615 of 947
Power Steering (11.02)
Steering (11.00)11-2-12 Workshop Manual Issue 5, January 2010
Removal
1. Remove PAS fluid from reservoir (syringe).
2. Remove throttle body duct for access. (clips x3).
3. Remove top bolts (x2) from engine oil tank and loosen
bottom bolts (x2) (allows ta nk to move to access pipe
support fixings).
4. Remove bolts (x2) securing pipe to body.
5. Disconnect sensor multiplug.
6. Remove hose from pump union.
7. Remove pipes from steering rack (bolt x1).
8. Remove pipe from vehicle.
Installation
1. Renew o-rings on PAS pipes and pump pipe.
2. Install hose to vehicle.
3. Install bolts brackets to body.
4. Install PAS pipes to rack (bolt x1).
5. Connect sensor multiplug.
6. Install pipe to pump union.
7. Install bolts and tighten oil tank fixings (torque).
8. Install throttle body duct. (clips x3).
9. Bleed PAS system (see Workshop Manual procedure 11.01.AA Power Assisted Steering System - Bleed).
Power Steering Rack to Cooler Hose-
Renew
Removal
1. Remove radiator grille (see Workshop Manual
procedure 01.08.AA Grille - Radiator - Renew).
2. Remove PAS fluid from reservoir (syringe). 3. Remove hose from cooler (clip x1) and support clips
(x2).
4. Remove undertray (see Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
5. Remove bolt, bracket to lower radiator crossmember.
6. Lower ramp.
7. Remove throttle body duct for access. (clips x3).
8. Remove pipes from st eering rack (bolt x1).
9. Remove hose from vehicle (support clips x2).
Installation
1. Renew the O-rings on the PAS pipes.
2. Install hose to vehicle (support clips).
3. Install PAS pipes to rack (bolt x1).
4. Install throttle body duct. (clips x3).
5. Raise ramp.
6. Install support clip bolt to radiator crossmember.
7. Install hose to cooler and support clips (x2).
8. Install undertray (see Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
9. Install radiator grille (see Workshop Manual procedure 01.08.AA Grille - Ra diator - Renew).
10. Top up PAS fluid.
WAR NI NG
AVOID EXCESSIVE SKIN CONTACT WITH MINERAL
OIL. MINERAL OILS REMOVE THE NATURAL FATS
FROM THE SKIN, LEADING TO DRYNESS, IRRITATION AND DERMATITIS.
Caution
Always plug pipes and hoses to prevent ingress of dirt or
moisture into the system.
Repair Operation Time (ROT)
Caution
Always plug pipes and hoses to prevent ingress of dirt or moisture into the system.
Page 939 of 947
Service Bulletin SB-17-0298
February 2009 Page 2 of 5
Figure 2
1
SB0298-03
Figure 3
6. Attach an airline that has dry air, without oil to
the battery vent tube (refer to Figure 4)
CAUTION: MAKE SURE THAT THE
AIRLINE PRESSURE IS 2 BAR
OR LESS. IF YOU DO NOT,
DAMAGE TO THE HEADLAMP
CAN OCCUR.
Figure 4
7. Make sure that the opposite end of the vent tube has
not moved inside the headlamp. If necessary, adjust its
position.
8. Blow air through the headlamp until you can see no condensation remaining on the lens.
9. Let the air flow for 20 minutes more.
10. Remove the vent tube from the headlamp then do st eps 11 to 13 that follow quickly before more moisture
can get into the headlamp.
11. Remove the cover for the main-beam bulb.
12. Install two silica gel bags into the headlamp at
the positions shown in Figure 5.
Figure 5
13. Install the two bulb covers. Make sure that the covers are fully installed correctly.
Page 941 of 947
Service Bulletin SB-17-0298
February 2009 Page 4 of 5
7. Attach an airline that has dry air, without oil to
the battery vent tube (refer to Figure 9)
CAUTION: MAKE SURE THAT THE
AIRLINE PRESSURE IS 2 BAR
OR LESS. IF YOU DO NOT,
DAMAGE TO THE HEADLAMP
CAN OCCUR.
Figure 9
8. Blow air through the headlamp until you can see no condensation on the lens.
9. Let the air flow for 20 minutes more.
10. Remove the vent tube from the headlamp then do steps 11 and 12 that follow quickly before more
moisture can get into the headlamp.
11. Install two silica gel bags into the headlamp
(refer to Figure 10 – right headlamp shown).
Figure 10
12. Install the bulb cover.
13. Install and tighten the two screws that attach the bulb cover.
14. Install the headlamp access panel and turn the quarter turn fastener to attach it.
15. Lower the vehicle.
16. Adjust the steering to the centre.
Part Data
Description Part Number Quantity
25g Silica Gel Bag (2 each pa ck) 9G43-37-11095-PK 2 per headlamp
Battery Vent Tube 1R12-372635-AA 1